SECO-LARM ENFORCER SK-910RAV2Q Installation Manual

ENFORCER RF R
ECEIVERS
Specifications:
SK-910RAQ
Range Up to 500' range
Operating Voltage 11-24 V AC/DC (16~24 VAC/DC must cut LP4)
Memory Capacity 15 transmitter button codes per channel
Current Draw 5mA standby, 50mA LED
flashing @ 12VDC
Output mode Programmable 4-sec. momentary (default), 1-sec. momentary, toggle (ON/OFF), or validity
Output type
3A Form 'C' relay (NO/NC/C).
Dimensions 3 / " x 2 / " x / " (80 x 65 x 19 mm)
3 9 3
16 16 4
Frequency 315MHz. (Other frequencies available. Please contact SECO-LARM.)
Transmitter
Compatible with all SECO-LARM transmitters
Compatible Transmitters
Fixed-Code: 68 billion codes. CODEBUMP
TM
Pendant Remotes
# of # of
Model Number
Buttons Channels
SK-919TD1S-U
1 1
SK-919TD1S-UP
SK-919TD2A-U
SK-919TD2A-UP 2 3
SK-917T2A
SK-919TP3J-N
3
7
SK-917T3J
SK-919TP4J-N
4
15
SK-917TP4J-N
Hand-Held Remotes
# of # of
Model Number
Buttons Channels
SK-919TP1H-B 1 1
SK-919TP2H-N 2 3
SK-919TP4H-N 4 15
Accessories
SK-9HBC Belt clip holster for hand-held remotes
WARRANTY: These ENFORCER RF receivers are warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original customer. Our obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation pre-paid, to SECO-LARM.
Copyright © 2013 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
The SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without further notice.
SECO-LARM U.S.A., Inc. U.S.A., Inc. U.S.A., Inc. U.S.A., Inc. U.S.A., Inc.
®
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
SK-910RAVQ
SK-910RAV2Q
Up to 500' range
3-13.8 VDC
5mA standby, 15mA LED flashing @ 12VDC
Transistor GND x 1, 5A @ 12VDC Transistor GND x 2, 3A @ 12VDC
code-hopping: 18 quintillion (1.8 x 10 ) codes
19
Blank or
CODEBUMP
Coding
Pre-coded
With SECO-LARM's
Fixed Blank
CODEBUMP, so-called code-
Fixed Pre-coded
grabbers and scanners are
Fixed Blank
rendered obsolete because
Fixed Pre-coded
the RF code changes every
Code Hopping Pre-coded
time the transmitter button is
Fixed Pre-coded
pressed. In addition, with
Code Hopping Pre-coded
over 18 quintillion (1.8 x 10
Fixed Pre-coded
codes, the chances of ever
Code Hopping Pre-coded
repeating a code are virtually
non-existent.
Blank or
Coding
SECO-LARM's CODEBUMP
Pre-coded
transmitters and receivers
Fixed Pre-coded
are perfect for controlling
Pre-coded
Fixed
garage and gate openers,
Pre-coded
Fixed
car and home alarms,
plus much more.
FILE: D\DTP\Manual\MISK910RAV2Q_1304.pmd
Order Part #762-107-4%
Website: www.seco-larm.com
E-mail: sales@seco-larm.com
Installation Manual
ENFORCER
SK-910RA SK SK SK SK -910RA -910RA -910RA -910RAQ SERIES
Miniature RF Miniature RF Miniature RF Miniature RF Miniature RF
R R R R R eceivers eceivers eceivers eceivers eceivers
Up to 500 ft. range
Operate on 11-24VAC/DC
Code learning
FCC compliant
TM
Fixed code or CODEBUMP
Introduction
These mini RF receivers are compatible with both code hopping and fixed-code transmitters (see page 4 of this manual
for a list of compatible transmitters). They can be used for a variety of applications, such as allowing the same transmitter to
arm/disarm a vehicle alarm and open/close a garage door opener. The receivers come in one- or two-channel versions.
Each channel can learn the codes of up to 15 different transmitter buttons on a first-in, first-out basis.
Installation Notes
)
19
1. Mount out of sight in a location where it is not surrounded by metal, and where it is not exposed to the weather or
moisture. Metal will block the RF signal, resulting in a reduced range.
2. For best range, pull the antenna wire as straight and high as possible. If the receiver receives interference from local
RF activity (eg., airport or military base), the antenna wire can be folded. DO NOT CUT THE ANTENNA WIRE.
Models Available
SK-910RAQ .......... 1-channel mini-receiver, 3A Form "C" relay, 315MHz
SK-910RAVQ ........ 1-channel mini-receiver, 5A transistor ground output, 315MHz
SK-910RAV2Q ...... 2-channel mini-receiver, 3A transistor ground outputs, 315MHz
SK-910RA-4Q ....... 1-channel mini-receiver, 3A Form "C" relay, 433.92MHz
SK-910RAV-4Q ..... 1-channel mini-receiver, 5A transistor ground output, 433.92MHz
SK-910RAV2-4Q .. 2-channel mini-receiver, 3A transistor ground outputs, 433.92MHz
More RF receivers are available (1 to 4 channels). Contact SECO-LARM for details.
PITSW1
®
SECO-LARM SECO-LARM SECO-LARM SECO-LARM SECO-LARM
Page 4

Q SERIES Q SERIES Q SERIES Q SERIES
1
code-hopping
TM
All models work on 11-24VAC/DC, except for the low voltage versions.
1
® ® ® ® ®
ENFORCER RF R
ECEIVERS
SK-910RAQ Shown