SECO-LARM SLI ENFORCER SK-910RAVQ Installation Manual

SECO-LARM SLI ENFORCER SK-910RAVQ Installation Manual

Miniature rf receivers

Advertisement

Quick Links

Installation Manual
ENFORCER
SK
SK
-910RA
-910RA
SK
SK -910RA
SK
-910RA
-910RA Q SERIES
Miniature RF
Miniature RF
Miniature RF
Miniature RF
Miniature RF
R R R R R eceivers
eceivers
eceivers
eceivers
eceivers
Up to 500 ft. range
Operate on 11-24VAC/DC
Code learning
FCC compliant
Fixed code or CODEBUMP

Introduction

These mini RF receivers are compatible with both code hopping and fixed-code transmitters (see page 4 of this manual
for a list of compatible transmitters). They can be used for a variety of applications, such as allowing the same transmitter to
arm/disarm a vehicle alarm and open/close a garage door opener. The receivers come in one- or two-channel versions.
Each channel can learn the codes of up to 15 different transmitter buttons on a first-in, first-out basis.

Installation Notes

1. Mount out of sight in a location where it is not surrounded by metal, and where it is not exposed to the weather or
moisture. Metal will block the RF signal, resulting in a reduced range.
2. For best range, pull the antenna wire as straight and high as possible. If the receiver receives interference from local
RF activity (eg., airport or military base), the antenna wire can be folded. DO NOT CUT THE ANTENNA WIRE.

Models Available

SK-910RAQ .......... 1-channel mini-receiver, 3A Form "C" relay, 315MHz
SK-910RAVQ ........ 1-channel mini-receiver, 5A transistor ground output, 315MHz
SK-910RAV2Q ...... 2-channel mini-receiver, 3A transistor ground outputs, 315MHz
SK-910RA-4Q ....... 1-channel mini-receiver, 3A Form "C" relay, 433.92MHz
SK-910RAV-4Q ..... 1-channel mini-receiver, 5A transistor ground output, 433.92MHz
SK-910RAV2-4Q .. 2-channel mini-receiver, 3A transistor ground outputs, 433.92MHz
More RF receivers are available (1 to 4 channels). Contact SECO-LARM for details.
All manuals and user guides at all-guides.com
Q SERIES
Q SERIES
Q SERIES
Q SERIES
1
TM
All models work on 11-24VAC/DC, except for the low voltage versions.
1
®
®
SK-910RAQ Shown
code-hopping

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SLI ENFORCER SK-910RAVQ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SECO-LARM SLI ENFORCER SK-910RAVQ

  • Page 1 SK-910RAV-4Q ..1-channel mini-receiver, 5A transistor ground output, 433.92MHz SK-910RAV2-4Q .. 2-channel mini-receiver, 3A transistor ground outputs, 433.92MHz More RF receivers are available (1 to 4 channels). Contact SECO-LARM for details. All models work on 11-24VAC/DC, except for the low voltage versions.
  • Page 2 All manuals and user guides at all-guides.com ENFORCER RF R ECEIVERS Learning a New Button Code (channel 1) 1. Press the mode switch which is located at the top of the receiver case for three seconds. The green LED will start to flash quickly.
  • Page 3 All manuals and user guides at all-guides.com ENFORCER RF R ECEIVERS SK-910RAQ SK-910RAVQ/RAV2Q Mode switch #2 Loop 3 (SK-910RAV2Q only) Mode switch #1 Ext. range antenna connector Mode switch #1 Loop 2 Loop 1 Loop 4 Channel 1 Status LED Channel 2 Status LED (SK-910RAV2Q only)
  • Page 4 SECO-LARM. Copyright © 2016 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

This manual is also suitable for:

Sli enforcer sk-910raq seriesSli enforcer sk-910rav2qSli enforcer sk-910ra-4qSli enforcer sk-910rav-4qSli enforcer sk-910rav2-4q

Table of Contents