Specifications; Specific Safety Rules; Functional Description - Makita FS6300 Instruction Manual

ENGLISH
1. Lock ring
2. Locator
3. Switch trigger
4. Lock button
5. Lamp

SPECIFICATIONS

Capacities
No load speed (min
Overall length
Safety class
• Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
• Note: Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to
screwdriver safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious
personal injury.
1. Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring or its own cord.
Fasteners contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
2. Always be sure you have a firm footing.Be sure no
one is below when using the tool in high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immediately
after operation; they may be extremely hot and
could burn your skin.
SAVE THESE INSTRUCTIONS.
Explanation of general view
6. Reversing switch lever
7. Hook
8. Gear housing
9. Bit
10. Magnetic bit holder
Model
Self drilling screw
Drywall screw
-1
)
Net weight
FS4000
6 mm
5 mm
0 - 4,000
269 mm
1.3 kg
WARNING:
ENE033-1
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
ENF002-1

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Depth adjustment (Fig. 1)
GEB017-2
The depth can be adjusted by turning the lock ring. Turn it
in "B" direction for less depth and in "A" direction for more
depth. One full turn of the lock ring equals 1.5 mm change
in depth.
Adjust the lock ring so that the distance between the tip of
the locator and the screw head is approximately 1 mm as
shown in the figures. Drive a trial screw into your material
or a piece of duplicate material. If the depth is still not
suitable for the screw, continue adjusting until you obtain
the proper depth setting. (Fig. 2 & 3)
Switch action (Fig. 4)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
11. Swells
12. Trapezoidal holes
13. Locator holder
FS4300 /
FS4200
FS4300A
6 mm 6 mm
5 mm 5 mm
0 - 4,000 0 - 4,000
269 mm 279 mm
1.4 kg 1.4 kg
/II
FS6300 /
FS6300R
FS6300A
- -
4 mm 4 mm
0 - 6,000 0 - 6,000
279 mm 279 mm
1.4 kg 1.4 kg
5