Summary of Contents for Emerson ACC/ARTM-7221/SCSI
Page 1
ACC/ARTM-7221/SCSI Installation Guide 6806800F01A March 2008...
Page 2
Emerson reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of Emerson to notify any person of such revision or changes.
IPMI Intelligent Platform Management Interface Linear Feet per Minute Logical Unit Number Mezzanine Management Controller NEBS Network Equipment Building System Out-Of-Service Peripheral Component Interconnect PICMG PCI Industrial Computer Manufacturers Group PCI Mezzanine Card Rear Transition Module ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Page 10
Repeated item for example node 1, node 2, ..., node 12 Omission of information from example/command that is not necessary at the time being Ranges, for example: 0..4 means one of the integers 0,1,2,3, and 4 (used in registers) Logical OR ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Page 11
Updated front panel description; editorial changes; included 3D graphics; included IPMI information; updated connector description;:renamed RTM to new official name: ACC/ARTM- 7221/SCSI; added power requirements and critical temperature limits; renamed RTM to ACC/ARTM-7221/SCSI (new official product name) 224618 April 2006 Update for final release...
Page 12
About this Manual In "Area of Interest" select "Technical Documentation". Be sure to include the title, part number, and revision of the manual and tell us how you used it. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
The RTM has been tested in a standard Emerson system and found to comply with the limits for a Class A digital device in this system, pursuant to part 15 of the FCC Rules, EN 55022 Class A respectively.
Page 14
LED is permanently ON. RTM Damage Installing the RTM with other blades than the PENT/ATCA-7221 damages the RTM. Only install the RTM with the Emerson PENT/ATCA-7221 blade. Operation RTM damage High humidity and condensation on the RTM surface causes short circuits.
Page 15
Therefore, only connect E1/T1 networks to RJ-45 connectors labeled as E1/T1 ports and only connect serial devices to RJ-45 connectors labeled as COM. Environment Always dispose of used RTMs according to your country's legislation, if possible in an environmentally acceptable way. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Die in diesem Handbuch enthaltenen Informationen dienen ausschließlich dazu, das Wissen von Fachpersonal zu ergänzen, können es aber in keinem Fall ersetzen. Das RTM wurde in einem Emerson Standardsystem getestet. Es erfüllt die für digitale Geräte der Klasse A gültigen Grenzwerte in einem solchen System gemäß den FCC- Richtlinien Abschnitt 15 bzw.
Page 18
Beschädigung des RTMs Wenn Sie das RTM nicht zusammen mit dem PENT/ATCA-7221 Front Blade installieren, wird das RTM beschädigt. Installieren Sie das RTM deshalb nur zusammen mit dem Emerson PENT/ATCA-7221 Front Blade. Datenverlust Wenn Sie das RTM aus einem eingeschaltetem System herausziehen während die blaue LED auf dem Front Blade noch blinkt, gehen Daten verloren.
Page 19
Schließen Sie deshalb nur E1/T1 Netze an die mit E1/T1 gekennzeichneten Stecker an und schließen Sie nur serielle Geräte an die mit COM gekennzeichneten Stecker an. Umweltschutz Entsorgen Sie alte RTMs stets gemäß der in Ihrem Land gültigen Gesetzgebung, wenn möglich immer umweltfreundlich. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
We welcome and appreciate your comments on our documentation. We want to know what you think about our manuals and how we can make them better. Mail comments to: Emerson Network Power - Embedded Computing GmbH Lilienthalstraße 15 85579 Neubiberg Germany Email: reader-comments@mcg.mot.com...
Features Features The ACC/ARTM-7221/SCSI is a rear transition module (RTM) which provides easy access to I/O signals of the Emerson PENT/ATCA-7221 front blade. The I/O signals are available via the zone 3 connectors. The RTM provides the following: Interfaces on face plate: –...
GR-63 4.3.2. The test consisted of dropping the RTM from 100mm height. As a result of the test, some locating pins were damaged which fix the two alignment blocks that are required by the PICMG 3.0 specification. Due to the damage, the alignment blocks were allowed to rotate slightly. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Page 24
Introduction Standard Compliances Note: The product has been designed to meet the directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS) Directive ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Page 25
Standard Compliances Introduction 2002/95/EC. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
When ordering RTM variants, use the order numbers given below. 1.5.1 Product Nomenclature As of the time of writing this guide, the following RTM variant was available. Consult your local Emerson sales representative for a more up-to-date list. Order Number Variant name Description...
Action Plan - Part 1 Start Installation Inspect delivered package items Make sure requirements are met Hard disk to be connected or to be installed? Connect/install hard disk IPMB1 device to be connected? Connect IPMB1 device ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Is slot powered? Switch on system power Switch off slot power Install RTM Install RTM Install RTM Cables to face plate connectors necessary? Connect cables to face plate connectors Switch on slot power Installation finished ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Electrostatic discharge and incorrect RTM installation and removal can damage circuits or shorten their life. Before touching the RTM or electronic components, make sure that you are working in an ESD-safe environment. The ACC/ARTM-7221/SCSI comes delivered as accessory kit consisting of this Installation Guide and the RTM. 2.2.2 Requirements Before installing the RTM, make sure the requirements described in this section are met.
0.5 mm amplitude 1g 1 mm amplitude 2.0 g 5-20 Hz 20-250 Hz Shock 5 g/11 ms halfsine according to 15 g/11 ms half sine according to Emerson- Emerson-internal environmental internal environmental requirements requirements Free Fall 1,200 mm/all edges and corners In order to ensure proper RTM operation, you have to make sure that the temperatures at the following locations are not exceeded.
For installing the RTM, you need a system without a zone 3 midplane. On-Board Connectors The RTM provides the following on-board connectors: IPMB1 Before installing the RTM, you may want to connect devices to these connectors. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
The Serial Attached SCSI (SAS) connector allows to install an on-board 2.5" SAS hard disk which is available as accessory kit called ACC/ATCA-7221/HDD/SAS for the RTM. For further information refer to the ACC/ATCA-7221/HDD/SAS Installation Guide which can be downloaded from the Emerson literature catalog. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
The following connector pinout gives information on which signal is assigned to which pin. Table 2-2 SAS Connector Pinout Segment Name Primary Signal GROUND Primary Signal Primary Signal Primary Signal GROUND Primary Signal Primary Signal Primary Signal GROUND Secondary Signal GROUND Secondary Signal Secondary Signal Secondary Signal GROUND ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
The ARTM can be installed into a powered or nonpowered system and must be installed into a AdvancedTCA system without a zone 3 midplane. RTM Damage Installing the RTM with other blades than the PENT/ATCA-7221 damages the RTM. Only install the RTM with the Emerson PENT/ATCA-7221 blade. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
7. Tighten the two face plate screws 8. Plug interface cables into the face plate connectors, if applicable 9. Turn on system power ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
The blue LED on the front blade starts to flash. This indicates that the front blade is informing the shelf manager about its desire to power down its payload. 3. Wait until the blue LED on the front blade is ON ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Page 39
2. Insert the ARTM into the shelf by placing the top and the bottom edges in the card guides of the slot 3. Slide the ARTM into the slot 4. Hook the lower and the upper handle into the shelf rail recesses ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Page 40
Removing the RTM with the system power on and the blue LED on the front blade still flashing causes data loss. Before removing the RTM from a powered system, power down the slot by opening the lower handle of the front blade and wait until the blue LED is permanently ON. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Page 41
Incorrect RTM installation and removal can result in RTM malfunctioning. When plugging the RTM in or removing it, do not press on the face plate but use the handles. 6. Remove the ARTM from the slot ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Figure 2-7 Face Plate ETH 1 COM 2 COM 3 ETH 2 E1/T1 P2 E1/T1 P1 E1/T1 P4 E1/T1 P3 2.5.1 Connectors The face plate of the RTM provides the following connectors: One USB 2.0 Keyboard/mouse ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Page 43
Connectors Installation Two Ethernet interfaces Two serial (RJ-45) Four E1/T1 ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Installation Connectors One SAS interface Two SCSI interfaces Figure 2-8 Face Plate Connectors ETH 1 COM 2 COM 3 ETH 2 E1/T1 P2 E1/T1 P1 E1/T1 P4 E1/T1 P3 ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
One PS/2 keyboard or one PS/2 mouse can directly be connected to the RTM. If you use a splitter cable, you can connect a PS/2 keyboard and mouse simultaneously. The following connector pinout gives information on which signal is assigned to which pin. Figure 2-10 Keyboard/Mouse Connector Pinout KBD_DATA MSE_DATA VP5_KBD KBD_CLK MSE_CLK ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
COM or connecting a serial device to a RJ-45 connector labeled as E1/T1 may damage the telephone or the RTM. Therefore, only connect E1/T1 networks to RJ-45 connectors labeled as E1/T1 ports and only connect serial devices to RJ-45 connectors labeled as COM. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
The RTM face plate provides four E1/T1 interface connectors at its face plate. The respective signals derive from a PMC-8260/DS1 installed on the front blade. Depending on the PMC- 8260/DS1 variant, up to four E1/T1 interfaces are available at the RTM's face plate. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
The following connector pinout gives information on which signal is assigned to which pin. The "x" stands for the number of the interface. Figure 2-13 E1/T1 Connector Pinout RX-_x RX+_x n.c. TX-_x TX+_x n.c. n.c. n.c. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
The following connector pinout gives information on which signal is assigned to which pin. Figure 2-14 SAS Connector Pinout Rx 2- Rx 2+ Rx 3- Rx 3+ n.c. n.c. n.c. n.c. n.c. n.c. n.c. n.c. Tx 3+ Tx 3- Tx 2+ Tx 2- ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Yellow: Ethernet link is established Right LEDs Indicates whether there is Ethernet activity or not OFF: No Ethernet activity Green: Ethernet activity Indicates whether there is SAS hard disk activity or not OFF: No SAS activity Green: SAS activity ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
By pressing on the reset key, you reset the RTM and the front blade. The following figure shows the location of the reset key. The RTM's MMC and the front blade's IPMC are not reset via this key. Figure 2-17 Face Plate Reset Key ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
The RTM provides two zone 3 connectors: P30 and P31. They provide interfaces to: Serial (RS-232) PCI Express Keyboard/Mouse IPMI Power PMC user I/O The following figure shows the location of P30 and P31. Figure 2-18 Location of Zone 3 Connectors P30 and P31 ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Management Controller The RTM provides the a Mezzanine Management Controller (MMC) based on the Atmega64L controller which is fully compliant to the IPMI V 1.5 standard. The MMC is connected to the front blade's IPMC via IPMB1. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
RTM FW Revision Firmware revision Application firmware revision Discrete Always RTM-7221 MMC Reset type Status and type of the last reset of Discrete Always the IPMC BOOT FW Revision Firmware revision Boot loader firmware revision Discrete Always ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Figure 2-23 Location of Temperature Sensor ARTM-7221 Temp. For further details about these sensors as well as further IPMI-relared information, refer to the ACC/RTM-7221/SCSI: Control via IPMI Programmer's Guide which can be downloaded from the Emerson literature catalog. ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
> Resource Center > Technical Documentation Search. This site provides the most up-to-date copies of Emerson Network Power - Embedded Computing product documentation. Note: Check the Emerson literature catalog for any erratas that may be applicable to the RTM. Company/ Organisation www.
Page 60
Related Documentation Emerson Network Power - Embedded Computing Documents ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)
Ethernet connector Keyboard/mouse connector LEDs Reset key Requirements SAS connector Power requirements SCSI connector Serial connector USB connector Standard compliances Installation Temperatures Into nonpowered systems Non-operating Into powered systems Operating IPMI sensors Zone 3 connectors Main features ACC/ARTM-7221/SCSI Installation Guide (6806800F01A)