HunterDouglas PowerView Installation Operation Care
Ac automation for standard, fascia, pocket, & coupled
Hide thumbs
Also See for PowerView:
- Manual (24 pages) ,
- Quick start manual (14 pages) ,
- User manual (6 pages)
Related Manuals for HunterDouglas PowerView
Summary of Contents for HunterDouglas PowerView
- Page 1 Installation Operation Care • • Designer Roller & Designer Screen Shades with PowerView AC Automation for ® Standard, Fascia, Pocket, & Coupled...
-
Page 2: Table Of Contents
STEP 1 — Install the Brackets ..........6 STEP 2 — Install the Shade ..........15 STEP 3 — Connect the Power Source ........18 OPERATION Testing the Shade ..............18 Using the PowerView Remote ..........19 ® Resetting Shade Programming ..........21 Adjust Shade Limits (If Necessary) ........21 Install the Fascia Panel ............22... -
Page 3: Standard Shade
PRODUCT VIEW Standard Shade Motor Bracket Bracket Covers (Optional) Bracket Idle Covers Bracket Motor (Optional) Assembly Installation Screws Idler Assembly Bottom Rail... -
Page 4: Coupled Shade
PRODUCT VIEW Coupled Shade Bracket Motor Covers Bracket Bracket Motor Covers Assembly Intermediate Bracket Bracket Covers Idler Assembly Idle Bracket Bottom Rail... -
Page 5: Fascia Shade
PRODUCT VIEW Fascia Shade End Cap Fascia Tape Motor Bracket Fascia Fascia Clutch Idle Bracket Motor Assembly End Cap (Optional) Idler Assembly Bottom Bar End Cap... -
Page 6: Pocket Shade
PRODUCT VIEW Pocket Shade Pocket End Cap Pocket Pocket End Cap Idle-Side Installation Motor Bracket Assembly Pocket Bottom Idler Assembly Bottom Rail... -
Page 7: Tools And Fasteners Needed
GETTING STARTED Thank you for purchasing Hunter Douglas Roller and Screen Shades with PowerView ® Automation. With proper installation, operation, and care, your new shades will provide years of beauty and performance. Please thoroughly review this instruction booklet and the enclosed packing list before beginning the installation. -
Page 8: Installation
INSTALLATION Installation Overview To install your shade, you will need to perform the following three steps: STEP 1: Install the brackets and attach additional components STEP 2: Install the shade STEP 3: Connect the power source STEP 1 — Install the Brackets Mounting Types and Window Terminology If the installation brackets are mounted correctly, the rest of the installation process follows easily. - Page 9 INSTALLATION Inside/End Mount — Standard Shades If you ordered bracket covers. Mark ⁄ " in from each window jamb for the outside ■ edge of each bracket. Shades without bracket covers. Mark ⁄ " in from each window jamb for the outside ■...
- Page 10 INSTALLATION Outside Mount — Standard Shades Determine the bracket locations. ■ Center the ordered width over the window at the desired height and mark its location. ➤ Place the outside edge of each bracket ⁄ " in from the previously made marks, then mark ■...
- Page 11 INSTALLATION Inside Mount — Coupled Shades If you ordered bracket covers. Mark ⁄ " in from each window jamb for both the motor ■ and idle brackets. Shades without bracket covers. Mark ⁄ " in from each window jamb for both the ■...
- Page 12 INSTALLATION Install the Bracket Covers (If Ordered) If you ordered bracket covers. Install the bracket covers by ■ Bracket aligning the bracket cover channels with the bracket and sliding Cover it onto the bracket. Bracket Cover Proceed to “STEP 2 — Install the Shade” on page 15.
- Page 13 INSTALLATION Outside Mount — Coupled Shades Center the total coupled ordered width over the window casement and mark each end. ■ To mark the location for your intermediate brackets, measure from the end mark near the ■ motor the motor panel ordered width and make a mark. For three or more coupled shades, the remaining intermediate brackets will be marked ■...
- Page 14 INSTALLATION Fascia Shades Assemble the two end brackets and Fascia ■ Panel the fascia panel. Place the top of the fascia panel into the top ➤ indention of the brackets. Rotate the panel down and snap it into place. IMPORTANT: Check that the outer surfaces of the brackets are flush with the ends of the panel.
- Page 15 INSTALLATION Inside/End Mount. Use your marks to position each bracket and mark each of the ■ screw holes. The minimum mounting depth required and fully recessed depth is 4 ⁄ ". ➤ Drill the screw holes using a ⁄ " drill bit. ■...
- Page 16 INSTALLATION Pocket Shades CAUTION: Hunter Douglas strongly recommends that shades in a pocket be mounted through wood or metal studs by a professional installer. The number of #10 x 1 ⁄ " Phillips hex washer head screws (not provided) required will vary depending on the width of the shade, as shown in the table below.
-
Page 17: Step 2 - Install The Shade
INSTALLATION STEP 2 — Install the Shade CAUTION: The antenna attached to the motor is fragile. Be careful unwrapping and handling the shade so antenna does not get damaged. Your shade may be standard roll or reverse roll based on your order. Be sure to orient the shade correctly before installing. - Page 18 INSTALLATION Slide the shade into the motor bracket until it clicks into place. Refer to the images below ■ for how to orient your shade. Gently pull back on the shade to ensure it is secure. CAUTION: Be sure the power cable and antenna are not pinched or caught in the brackets.
- Page 19 INSTALLATION Coupled Shades NOTE: Follow the steps on “STEP 2 — Install the Shade” on page 15, the remaining coupled shades follow these steps. Insert the coupled aligner from the second shade ■ into the idle end of the installed shade. Insert Coupled Aligner...
-
Page 20: Step 3 - Connect The Power Source
OPERATION STEP 3 — Connect the Power Source The PowerView AC motor comes with a blunt end 3 wire power connection, refer to your ■ ® local electrical codes for wiring to 120V power. Testing the Shade Testing the shade with the programming button will allow you to ensure the motor and power source are working correctly. -
Page 21: Using The Powerview ® Remote
First, activate the remote by pulling both plastic tabs from the back battery compartment. IMPORTANT: If you have more than one remote see “Adding Additional Remote(s) to the PowerView Shade Network” in the PowerView Automation Remote Control Guide. ® OPEN... - Page 22 PowerView Scene Controller Guide or to the online PowerView Step-by-Step Guide at hunterdouglas.com/operating-systems/motorized/powerview-motorization/manuals. PowerView App Operation The PowerView App is the primary method of operation for a PowerView Plus system. The PowerView Hub is required for PowerView App operation. For information regarding setup ®...
-
Page 23: Resetting Shade Programming
OPERATION Resetting Shade Programming The programming reset erases shade programming from memory, including group assignments, preventing input devices from operating the shade. The primary use is to correct group and network assignments during installation. The reset does not affect travel limits or the favorite position. -
Page 24: Install The Fascia Panel
OPERATION Adjusting the Bottom Limit Use the remote to lower the shade to the fully closed position. ■ Deselect all group numbers on the remote. ■ Press and hold the programming button on the shade and press and release ▼ CLOSE on ■... -
Page 25: Install Pocket Bottom Panel
OPERATION Install Pocket Bottom Panel Attach the bottom of the pocket. ■ Place the bottom into the pocket at an angle. ➤ Hook the bottom to the ledge inside the pocket. ➤ Rotate it down to secure it into place. ➤... - Page 26 OPERATION Problem The shade is not responding to the PowerView remote. ® Solution IMPORTANT: A shade will not operate until it is joined to a group. See “Joining a Shade to a Group” on page 19. Check that the correct group number is selected.
-
Page 27: Removing The Shade
CARE Removing the Shade CAUTION: Before removing the shade, the shade should be fully raised. Pocket Shades Only. Remove the bottom cover. Lift up the edge of ■ the bottom cover. Disengage it from the ledge of the pocket. Fascia Shades Only. Remove the ■... -
Page 28: Cleaning Procedures
CARE Cleaning Procedures Hunter Douglas roller shades are made from dust-resistant materials which repel dirt and dust. The following options are available if your shade needs cleaning. Dusting Regular light dusting with a feather duster is all the cleaning needed in most ■... -
Page 29: Declarations
DECLARATIONS U.S. Radio Frequency FCC Compliance FCC ID information is located behind the motor-side end cap. The end cap may be removed to view this information. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. - Page 30 Piekstraat 2, 3071 EL Rotterdam, The Netherlands certify and declare under our sole responsibility that assemblies PV4 conform with the essential requirements of the EMC directive 2004/108/EC and R&TTE directive 1999/5/EC. A copy of the original declaration of conformity may be found at: www.hunterdouglas.com/RFcertifications.
- Page 32 If you are not thoroughly satisfied, simply contact Hunter Douglas at (888) 501-8364 or visit hunterdouglas.com. In support of this policy of consumer satisfaction, we offer our Lifetime Limited Warranty as described below.
Need help?
Do you have a question about the PowerView and is the answer not in the manual?
Questions and answers