Table of Contents
Advertisement
Quick Links
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit di-
fferent from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician
for help.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2)this device must accept any interference received,
including interference that may cause undesired
operation.
This equipment complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment. To
maintain compliance with FCC RF exposure compliance
requirements, please avoid direct contact to the
transmitting antenna during transmitting.
RF Exposure Warning!
This device contains transmitters and receivers which
emit Radio Frequency (RF) energy. The device is
designed to comply with the limits for exposure to RF
energy set by the Federal Communications Commission
(FCC) of the United States, Industry Canada (IC) of Canada,
and the regulating entities of other countries.
If you are still concerned about exposure to RF energy,
you can further limit your exposure by limiting the
amount of time you use the equipment or by placing
more distance between your body and the device,
since exposure level drops o dramatically with distance.
Mobility Sound PTT-600-VZ
Wireless Speaker Microphone
-----------------------------------------------
For Use with Zello on Android
Smart phone
Model No.: PTT-600-VZ
Made in Taiwan
Mobility Sound is trademark owned by Mobility Sound
Products, Taiwan. All other product or service names are
the property of their respective owners.
© 2015 Mobility Sound Products, Taiwan. All Rights
Reserved
Advertisement
Table of Contents
Related Manuals for Mobility Sound PTT-600-VZ
Summary of Contents for Mobility Sound PTT-600-VZ
- Page 1 RF energy set by the Federal Communications Commission Mobility Sound is trademark owned by Mobility Sound (FCC) of the United States, Industry Canada (IC) of Canada, Products, Taiwan. All other product or service names are and the regulating entities of other countries.
- Page 2 Controls and Connection Microphone: Front Firing Speaker This microphone picks up Received calls are heard over this the user’s voice audio speaker. The volume level is controlled using the volume keys on the phone. Clothing Clip The alligator-type clip secures the speaker, microphone to the user’s clothing during use.
- Page 3 Charging the Speaker Microphone The PTT-600-VZ speaker microphone has an internal Lithium Ion rechargeable battery pack which must be charged prior to operation, and must be recharged regularly. A fully charged battery will provide approximately 5 hours (or more) of continuous operation before needing to be recharged.
- Page 4 Pairing with a Smartphone The PTT-600-VZ speaker microphone is designed to work with smart phones running the Android operating system. Prior to normal operation, the phone and speaker microphone must be paired together using the following process: 1. Activate the pairing mode on the speaker microphone by holding down the multifunction button until the status LED ashes BLUE-RED-BLUE-RED continuously in sequence.
- Page 5 Setting Up the Zello App To get the Zello app on your phone and set it up to work with the PTT-600-VZ speaker microphone, do the following: 1. Install Zello from your Zello@Work network, or download the app from the Google Play store.
- Page 6 To activate Zello’s push-to-talk feature, press and hold the PTT button on the speaker microphone. When Zello is transmitting a call, audio will be picked up by the PTT-600-VZ’s built-in microphone. Incoming calls received by Zello will be heard over the PTT-600-VZ’s built-in speaker or through the optional earphone if you are using one.
- Page 7 OPTIONAL EAPRHONES Although the PTT-600-VZ has a built-in speaker for listening to received calls, some users may prefer to use a listen only earphone for enhanced privacy. The accessory jack on the speaker microphone will accept any mono earphone with a 3.5 mm audio plug.
- Page 8 Acts of God, abuse, misuse, improper or abnormal usage, faulty installation, improper maintenance, lightning, or other incidences of excessive voltage, or any tampering or repairs by other than a Mobility Sound authorized repair facility. It does not cover replacement of consumable parts, transportation costs, or damage in transit.
Need help?
Do you have a question about the PTT-600-VZ and is the answer not in the manual?
Questions and answers