Table of Contents
Advertisement
For models ZIFI240 and ZIBI240 with Custom Door Panels and Handles
THE INSTALLATION SPACE
NOTE: If installing between
frameless cabinets, a 1/2" wide
filler strip or side panel may
be needed on the hinge side.
The filler strip will act as a
spacer between the door case
and adjacent cabinet and will
prevent interference with the
cabinet door swing. The width
of the opening must include the
filler panels.
The product must be installed so that the custom panel front will
project 2-3/4" forward of adjacent cabinets. This position will allow
a full door swing and prevent interference with adjacent cabinetry.
The opening between cabinets must be 23-3/4" minimum. These
models can not be installed flush in 24"-deep cabinets.
• All models may be used freestanding.
Additional Specifications
• A 120 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall as shown. Electrical
must be located on rear wall as shown. NOTE: GFCI
(ground fault circuit interrupter) is not recommended.
Black or Stainless Steel Toekick Options
• These products are shipped with a stainless steel
toekick and a black toekick. For shipping purposes, one
of the toekicks will be secured to the back of the unit,
and the second will be installed on the unit. Keep the
unused toekick and any unused parts for future use.
CABINET
Dim. A
In a standard installation, the product
will project forward of adjacent
cabinets. See Dim. A.
Product
ZIFI240
ZIBI240
8
Design Guide
NOTE:
Water line location for
ZIBI240 model only
Standard
Installation
Front edge of
CABINET
product case
Front face
110°
120°
Dim. A
2-3/4"
2-5/8"
SIDE-BY-SIDE INSTALLATIONS
For a complete refreshment center, install a Fresh-
Food Refrigerator beside a Double-Drawer Refrigerator,
Beverage Center or Wine Chiller/Wine Reserve.
Or, install a Refrigerator with Icemaker beside a
Wine Chiller/Wine Reserve.
• A side-by-side installation requires at least a 47-1/2"-
wide opening. No trim kits required.
• Products must operate from separate, properly
grounded receptacles.
10-1/2"
34-1/2"-35"
15"
47-1/2" Min.
PRODUCT CLEARANCES
The Fresh-Food Refrigerator or Bar Refrigerator with
Icemaker is factory set for a 110° door swing.
When installed in a corner:
• Allow 16" minimum clearance on the hinge side for a
full 110° door swing.
• Allow 4-1/2" min. clearance on the hinge side for the
90° door swing and to allow racks to slide out.
16" Minimum to Wall
110 Door
Swing
110
NOTE: Custom handle clearances may vary.
NOTE: Right hand models illustrated. Allow the same
clearances on the opposite side for left hand fresh food
models ZIFI240 and ZIFS240 only. Models ZIBI240 and
ZIBS240 are not available with left hand door swing.
• Test the door swing. Carefully open and close the
door. The door should not rub or catch on adjacent
cabinetry. NOTE: When installing custom panel and
handle, use above clearances as a general guide but
adjust according to the installation.
Choose the location:
• These products may be closed in on the top and
three sides as long as the front is unobstructed for air
circulation and proper access to the door.
• Do not install these products where the temperature
will go below 55°F (13°C) or above 100°F (37°C).
• These products are not designed to be stacked one
over the other.
Locate
Outlet
10-1/2"
24"
14"
9"
9"
1-1/2"
90 Door
21-5/8"
Swing
23-5/8"
90
4-1/2" Minimum to Wall
31-51544-9
Advertisement
Table of Contents
