Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Runva T-2000
Summary of Contents for Runva T-2000
- Page 1 ELECTRICAL WINCH T-2000 T-X2000 T-X3000 Assembly & Operating Instructions...
-
Page 2: Table Of Contents
WINCH WORKING DEMONSTRATION ..........7 REPLACING THE WIRE ROPE ............. 7 MAINTENANCE ..................8 TROUBLE SHOOTING ................8 WINCH ASSEMBLY DRAWING ............. 9 WINCH PARTS LIST ................1 0 SPECIFICATION(T-2000) ..............1 1 SPECIFICATION(T-X2000) ..............1 2 SPECIFICATION(T-X3000) ..............1 3... -
Page 3: Introduction
INTRODUCTION Congratulations on your purchase of a high quality winch. We design and build winches to strict specifications and with proper use and maintenance should bring you years of satisfying service. WARNING - Read, study and follow all instructions before operating this device. -
Page 4: Safety Precautions
7. Braking System: Braking action is automatically applied to the winch drum when the winch motor is stopped and there is a load on the wire rope. A separate mechanical brake applies the braking action. 8. Control System: Your winch was made to provide you the ability to use it in a medley of operations. -
Page 5: General Tips For Safe Operation
WARNING – Avoid “shock loads” by using the control switch intermittently to take up the slack in the wire rope. “Shock loads” can far exceed the rate capacity for the wire rope and drum. WARNING – Do not exceeds maximum line pull ratings shown on the tables. WARNING –... -
Page 6: Winching Techniques A-Z
sounds your winch makes under various loads, the way the cable spools on the drum, etc. • Inspect the wire rope and equipment before each use. A frayed or damaged rope must be replaced immediately. Use only the manufacturer’s replacement rope with the exact specifications. -
Page 7: Winch Assembly And Mounting
q. The winch is meant for intermittent use. Under full load with a single line rig do not power in for more than a minute without letting the motor cool down for a few minutes and then resume the winching operation. r. -
Page 8: Mounting Drawing
6. Always use the hand saver when free-spooling and re-spooling the wire rope. Using the hand saver keeps your hands and fingers away from the rotating drum. 7. Check for proper drum rotation. Pull and turn the clutch knob to the “CLUTCH OUT”... -
Page 9: Winch Working Demonstration
When pulling a heavy load, place a blanket or jacket over the wire rope five or six feet from the hook. In the event of a broken cable it will dampen the snap back. For additional protection open the Fig 3.3 hood of the vehicle as shown in Fig 3.3 For pulls over 70% rated line pull, we recommend the use of the snatch block/pulley block to double line the wire rope. -
Page 10: Maintenance
4. Ensure that the new cable wraps in the same rotation direction as the old one. The cable should leave the drum from the bottom, under the drum. 5. Turning clutch to the “CLUTCH IN” position. 6. Retract Cable Assembly onto drum, first five wraps being careful not to allow kinking, then winch cable must be wound onto the drum under a load of at least 10% rated line pull. -
Page 11: Winch Assembly Drawing
WINCH ASSEMBLY DRAWING... -
Page 12: Winch Parts List
X0300300 Planetary Gear Assembly Used in T-X3000 X0200300 Planetary Gear Assembly Used in T-X2000 K0200300 Planetary Gear Assembly Used in T-2000 X0300400 Output Gear Ring Assembly Used in T-X2000/T-X3000 K0200400 Output Gear Ring Assembly Used in T-2000 X0300002 Drum Holder Plate X0300003 Locking Washerø5... -
Page 13: Specification(T-2000)
SPECIFICATION(T-2000) Rated line pull 2000 lbs (907 kgs) 12V:Input: 1.7kW / 2.3hp; Output: 0.6kW /0.8hp Motor: permanent magnet 24V:Input: 1.9kW / 2.6hp; Output: 0.7kW /0.9hp Gear reduction ratio 153:1 Cable (Dia.× L) Ø5/32"×49'(Ø4mm×15m) Drum size(Dia.× L) Ø1.24"×2.87" (Ø31.5mm×73 mm) Mounting bolt pattern 3.13"... -
Page 14: Specification(T-X2000)
SPECIFICATION(T-X2000) Rated line pull 2000 lbs (907 kgs) 12V:Input: 1.7kW / 2.3hp; Output: 0.6kW / 0.8hp Motor: permanent magnet 24V:Input: 1.9kW / 2.6hp; Output: 0.7kW / 0.9hp Gear reduction ratio 153:1 Cable (Dia.× L) Ø5/32"×49'(Ø4mm×15m) Drum size(Dia.× L) Ø1.24"×2.87" (Ø31.5mm×73 mm) Mounting bolt pattern 3.13"... -
Page 15: Specification(T-X3000)
SPECIFICATION(T-X3000) Rated line pull 3000 lbs (1361 kg) 12V:Input: 2.2kW / 2.9hp; Output: 0.8kW / 1.1hp Motor: permanent magnet 24V:Input: 2.4kW / 3.2hp; Output: 0.9kW / 1.2hp Gear reduction ratio 153:1 Cable (Dia.× L) Ø3/16"×46'(Ø4.8mm×14m) Drum size(Dia.× L) Ø1.24"×2.87" (Ø31.5mm×73 mm) Mounting bolt pattern 3.13"...
Need help?
Do you have a question about the T-2000 and is the answer not in the manual?
Questions and answers