Related Manuals for KT&C Omni IP Series
Summary of Contents for KT&C Omni IP Series
- Page 1 KNC-p3LR3IR KNC-p3LR4IR KNC-p3LR6IR 3 Megapixel Plug & Play Capable IP66 IR IP Low Profile Cameras Quick Operation Guide...
- Page 2 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Thank you for selecting this KT&C Omni IP Series product. For additional information please refer to the complete User Guide for this cameras series. End users should contact their KT&C Certified Dealer for service. Certified Dealers can obtain support directly from KT&C.
- Page 3 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 4 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
- Page 5 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Safety Instructions These instructions are intended to ensure that the camera is installed in a manner that avoids danger to persons or property loss. These precautionary measures are divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
- Page 6 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide according to the IEC60950-1 standard; or 802.3af PoE. Please refer to technical specifications for detailed information. ● If connecting several devices to one power supply, to avoid any overload that may cause over-heating or a fire hazard insure that the power supply is adequate for the power load.
- Page 7 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide (which is not a malfunction), and could compromise the performance of the sensor. ● The sensor may be damaged if exposed to laser energy, so when any laser equipment is in use, make sure that the sensor will not be exposed to the laser beam.
-
Page 8: Table Of Contents
KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Table of Contents 1 Appearance and Description ............8 2 Installation ..................10 2.1 Ceiling/Wall Mounting ..........11 2.2 Wall/Ceiling Mounting with a Gang Box ......15 2.3 Wall Bracket Mounting ..........17 2.4 Install the Micro SD Card .......... -
Page 9: Appearance And Description
KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide 1 Appearance and Description Figure 1-1 Cover, Base and Cables Figure 1-2 Lock Screw & Reset Button... - Page 10 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Table 1-1 Physical Description Description Cover and Bubble Camera/IR Module Micro SD Card Slot Network Cable Lens IR LED Power Cable Position Lock Hex Screw RESET [WPS] Button Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
-
Page 11: Installation
KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide 2 Installation Before you start: Make sure the camera is in good condition and all the accessory parts are included. Make sure all related equipment is powered-off during the installation. Check to insure that the specifications of the camera are correct for the installation environment. -
Page 12: Ceiling/Wall Mounting
KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing haze, distortion or improper scene exposure. ●... - Page 13 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide The drill template matches the adapter plate included with the camera; pairs of hole on the temple can be uses for mounting the camera directly without the plate. The adapter plate also fits single gang and round electrical boxes.
- Page 14 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide 3. Fix the adapter plate to the ceiling with the supplied screws, and expansion anchors if needed. Figure 2-4 Fix the Adapter Plate 4. Attach the dome base to the plate with the supplied screws. Figure 2-5 Fix the Dome Drive 5.
- Page 15 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Use a plier to remove the break-away part and route the cables via side outlet (as shown in Figure 2-4) if no cable hole is drilled in step 1, and connect the corresponding cables. Figure 2-6 Remove a Section of the Edge 6.
-
Page 16: Wall/Ceiling Mounting With A Gang Box
KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide 9. Tighten the hex screw to fix the camera in the desired direction. 10. Align the front cover to the dome base and tighten the front cover screws. Figure 2-8 Install the Front Cover 11. - Page 17 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Figure 2-9 Attach the Adapter Plate 2. Attach the dome base to the adapter plate with the supplied PM4X8 screws. Figure 2-10 Fix the Dome Drive 3. Connect the power cable if used, and the network cable.
-
Page 18: Wall Bracket Mounting
KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide 4. Align the front cover to the dome base and tighten the front cover screws. Figure 2-11 Install the Front Cover 1. Carefully remove any protection film to complete installation. Do not tear off the protection film until the installation is ... - Page 19 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide You need to purchase the matching wall bracket separately. Figure 2-12 Wall Bracket 2. Attach the dome base to the wall bracket with the supplied screws. Figure 2-13 Install the Camera...
-
Page 20: Install The Micro Sd Card
KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide 3. Align the front cover to the dome base and tighten the set screws on the front cover to complete the installation. Figure 2-14 Install the Front Cover 4. Carefully remove any protection film to complete installation. Do not tear off the protection film until the installation is ... - Page 21 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Figure 2-15 Remove the Front Cover 2. Insert the micro SD card to the card slot until you hear a click. 3. To remove the SD card, push in slightly on the inserted micro SD card to uninstall it from the camera.
-
Page 22: Setting The Camera Parameters Over The Lan
KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide 3 Setting the Camera Parameters over the LAN Purpose: To view and configure the camera via a LAN, you need to connect the network camera in the same subnet with your computer, and install the OMNI Finder or OMNI CMS software to search and change the IP of the network camera. - Page 23 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Use OMNI CMS software and to list the online devices. Please refer to the user manual for the OMNI CMS software for detailed information. 2. Change the IP address and subnet mask to the same subnet as that of your computer, or change your computer to match the address/subnet of the camera.
- Page 24 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Figure 3-2 Search Online Devices Devices can be discovered and displayed in the list in 15 seconds after they go online; devices will be removed from the list in 45 seconds after going offline. Search online devices manually:...
- Page 25 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide You can also click to refresh the online device list manually. The newly searched devices will be added to the list. You can click on each column heading to order the information; you can click to show the device table and hide the network parameter panel on the right side, or click...
- Page 26 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Figure 3-3 Select a Device Figure 3-4 Modify Network Parameters 4) Enter the IP address of network camera in the address field of the web browser to view the live video.
-
Page 27: Accessing Via A Web Browser
KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide The default value of the IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”. For accessing the network camera from different subnets, please set the gateway for the network camera after you log in. 4 Accessing via a Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version /... - Page 28 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug- It is recommended to close the web browser before finishing the installation of the plug-in.
- Page 29 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in (1)
- Page 30 KNC-p3LR_IR Low Profile IP Camera·Quick Operation Guide Figure 4-4 Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2-4 to login. For more detailed instructions about further configuration, please refer to the user manual for this series of network cameras.