Additional Specific Safety Rules; Additional Safety Information; Residual Risks - Stanley SJ60 Original Instructions Manual

ENGLISH
(Original instructions)
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
remove the battery pack, if detachable from the power
tool before making any adjustments, changing
accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.

ADDITIONAL SPECIFIC SAFETY RULES

Safety instructions for jigsaw
a. Hold power tools by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the opertator an electric shock.
b. Use clamps or another practical way to secure and
support the work piece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
c. Keep hands away from cutting area. Never reach
6
underneath the material for any reason. Hold front of saw
by grasping the contoured gripping area. Do not insert
fingers or thumb into the vicinity of the reciprocating blade
and blade clamp. Do not stabilize the saw by gripping the
shoe.
d. Keep blades sharp. Dull blades may cause the saw to
swerve or stall under pressure.
e. When cutting pipe or conduit ensure that they are free
from water, electrical wiring, etc.
f. Allow the motor to come to a complete stop before
withdrawing the blade from the kerf (the slot created
by cutting). A moving blade may impact the workpiece
causing a broken blade, workpiece damage or loss of
control and possible personal injury.
g. Do not touch the workpiece or the blade immediately
after operating the tool. They can become very hot.
h. Keep handles dry, clean, free from oil and grease. This
will enable better control of the tool.
i. Clean out your tool often, especially after heavy use.
Dust and grit containing metal particles often accumulate
on interior surfaces and could create an electric shock
hazard.
j. Do not operate this tool for long periods of time.
Vibration caused by the operating action of this tool may
cause permanent injury to fingers, hands, and arms. Use
gloves to provide extra cushion, take frequent rest periods,
and limit daily time of use.
k. Avoid prolonged contact with dust from sawing
activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals.
l. Avoid cutting nails. Inspect workpiece for any nails
and remove them before operation.
m. Don not cut oversize workpiece.
n. Make sure the blade is not contacting the workpiece
before the switch in turned on.
o. Do not leave the tool running. Operate the tool only
when hand held.
p. Some material contains chemicals witch may be toxic.
Take caution to prevent dust inhalation and skin contact.
Follow material supplier safety data.
q. Always switch off and wait for the blade to come to
complete stop before removing the blade from the
workpiece.

Additional safety information

WARNING: We recommend the use of a residual
current device with a residual current rating of
30mA or less.

RESIDUAL RISKS

In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are: