Hitachi SJ700-4000HFU2 Instruction Manual page 224

Chapter 4
Register No. Function name
1401h Terminal [1] function
1402h Terminal [2] function
1403h Terminal [3] function
1404h Terminal [4] function
1405h Terminal [5] function
1406h Terminal [6] function
1407h Terminal [7] function
1408h Terminal [8] function
1409h (Reserved)
140Ah (Reserved)
140Bh Terminal [1] active state
140Ch Terminal [2] active state
140Dh Terminal [3] active state
140Eh Terminal [4] active state
140Fh Terminal [5] active state
1410h Terminal [6] active state
1411h Terminal [7] active state
1412h Terminal [8] active state
1413h Terminal [FW] active state
1414h (Reserved)
Function
R/W Monitoring and setting items Data resolution
code
1 (RV: Reverse RUN), 2 (CF1: Multispeed 1 setting), 3 (CF2:
Multispeed 2 setting), 4 (CF3: Multispeed 3 setting), 5 (CF4:
C001 R/W
Multispeed 4 setting), 6 (JG: Jogging), 7 (DB: external DC
braking), 8 (SET: Set 2nd motor data), 9 (2CH: 2-stage
acceleration/deceleration), 11 (FRS: free-run stop), 12 (EXT:
external trip), 13 (USP: unattended start protection), 14: (CS:
commercial power source enable), 15 (SFT: software lock), 16
C002 R/W
(AT: analog input voltage/current select), 17 (SET3: 3rd motor
control), 18 (RS: reset), 20 (STA: starting by 3-wire input), 21
(STP: stopping by 3-wire input), 22 (F/R: forward/reverse
switching by 3-wire input), 23 (PID: PID disable), 24 (PIDC: PID
reset), 26 (CAS: control gain setting), 27 (UP: remote control
C003 R/W
UP function), 28 (DWN: remote control DOWN function), 29
(DWN: remote control data clearing), 31 (OPE: forcible
operation), 32 (SF1: multispeed bit 1), 33 (SF2: multispeed bit
2), 34 (SF3: multispeed bit 3), 35 (SF4: multispeed bit 4), 36
(SF5: multispeed bit 5), 37 (SF6: multispeed bit 6), 38 (SF7:
C004 R/W
multispeed bit 7), 39 (OLR: overload restriction selection), 40
(TL: torque limit enable), 41 (TRQ1: torque limit selection bit
1), 42 (TRQ2: torque limit selection bit 2), 43 (PPI: P/PI mode
selection), 44 (BOK: braking confirmation), 45 (ORT:
orientation), 46 (LAC: LAD cancellation), 47 (PCLR: clearance
of position deviation), 48 (STAT: pulse train position command
C005 R/W
input enable), 50 (ADD: trigger for frequency addition
[A145]), 51 (F-TM: forcible-terminal operation), 52 (ATR:
permission of torque command input), 53 (KHC: cumulative
power clearance), 54 (SON: servo-on), 55 (FOC: forcing), 56
(MI1: general-purpose input 1), 57 (MI2: general-purpose
C006 R/W
input 2), 58 (MI3: general-purpose input 3), 59 (MI4:
general-purpose input 4), 60 (MI5: general-purpose input 5),
61 (MI6: general-purpose input 6), 62 (MI7: general-purpose
input 7), 63 (MI8: general-purpose input 8), 65 (AHD: analog
command holding), 66 (CP1: multistage position settings
C007 R/W
selection 1 ), 67 (CP2: multistage position settings selection
2), 68 (CP3: multistage position settings selection 3), 69 (ORL:
Zero-return limit function), 70 (ORG: Zero-return trigger
function), 71 (FOT: forward drive stop), 72 (ROT: reverse drive
stop), 73 (SPD: speed / position switching), 74 (PCNT: pulse
C008 R/W
counter), 75 (PCC: pulse counter clear)
255 (no: no assignment)
- - Inaccessible
- - Inaccessible
C011 R/W 0 (NO), 1 (NC)
C012 R/W 0 (NO), 1 (NC)
C013 R/W 0 (NO), 1 (NC)
C014 R/W 0 (NO), 1 (NC)
C015 R/W 0 (NO), 1 (NC)
C016 R/W 0 (NO), 1 (NC)
C017 R/W 0 (NO), 1 (NC)
C018 R/W 0 (NO), 1 (NC)
C019 R/W 0 (NO), 1 (NC)
- - Inaccessible
4-153
Explanation of Functions
Data
resolution
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-