Subscribe to Our Youtube Channel
Related Manuals for Merax MS198969
Summary of Contents for Merax MS198969
- Page 1 USER’S MANUAL MS198969 Note: Following the principles of sustainable development, we may modify machines when necessary and will not notify again. It all depends on the actual product.
-
Page 2: Table Of Contents
Contents ..………………………………………… 1 1.Product Brief ……………………………………… 2 2.Security Precautions and Warnings ……………………………………… 4 3.Installation Instructions ………………………………………7 4.Using Instructions …………………………………………9 5.Routine Maintenance... -
Page 3: Product Brief
1. Product Brief Single function home use treadmill: Main parameters and parts list Main technical parameters Parameters Names Description Input power voltage AC 220-240V(50/60Hz) Motor power 1.5HP Speed 1.0-12 Km/h Running surface 350*1000 mm Max user weight 100KG Expand dimensions 1260*600*1180mm Packing list units... -
Page 4: Security Precautions And Warnings
2. Security Precautions and Warnings Tips: Before folding the treadmill, make sure that the gradient is "zero". Notice: Please read the instructions carefully before use. Indoor using and storing the treadmill, avoid dampness, and cannot be spilled by water. ... - Page 5 ----Otherwise, may cause the leakage and burst into flames. Don't use when the power cord is damaged or power plug pin is loose. ----Otherwise, will lead to an electric shock, short circuit or fire. Don't damage or bent by force or reverse the power cord. Don’t place heavy objects on machine, don't clamp the power line.
-
Page 6: Installation Instructions
Ground protection system! This product must be grounded. If the machine is dysfunctional, grounding will provide a good channel for electric current, in order to reduce the electric shock risk. This product is equipped with power plug with grounding conductor and plug. Completely insert the plug to standard socket. - Page 7 2. Remove the pre-installed screws M8*22. Use 5# hexagon wrench and screw M6*12 to lock and fix the base with the hole sites. Then install screw M8*22 back. M8*22 M6*12 3. Hold left & right columns, use 5# hexagon wrench and screw M8*55 to lock the console frame on the columns (Tighten all screws in above steps, and please notice not to clamp the cable by column).
- Page 8 6.Use plum knob to lock the upright column and the base. Plum knob 7.Put the safety key on the picture showing yellow area, then press the start button to start the treadmill. (Notice: The treadmill can only start when the safety key is put on the yellow area on the console.) Please find the red color safety key in the accessory bag.
-
Page 9: Using Instructions
picture：1 picture：2 picture：3 4. Using Instructions Using treadmill 1. Insert the power plug properly and turn on the switch (in red color) (1). When the light is on, there will be a beep sound, and then the screen will light up. 2. - Page 10 In standby mode, press this key can cycle the options of 3 different countdown running mode: time countdown running mode, distance countdown running mode and calorie countdown running mode. 4. Speed ± Use these keys to adjust the speed of the treadmill, press “+” to increase the speed and “-” to decrease the speed.
-
Page 11: Routine Maintenance
Translation of Error Codes Error code Description Solution Communication Abnormal: Possible Cause: the communication between the lower controller when the power is on, the and console is blocked, check each joint between the controller and connection between lower console, make sure that each core is fully plugged in. Check the connection line, replace it if it’s damaged. - Page 12 Heavyweight use (use more than 7 hours a week) once every half month. 1.In order to better safeguard your electric treadmill and extend the life of the machine, it is recommended that after your continued use of two hours, turn off the machine and let it rest for 10 minutes before using again.
- Page 13 flip the multi-wedge belt by 100%; if it is too tight, the degree for you to flip the belt is very limited. It is appropriate to flip the multi-wedge belt by 80% after adjustment. Please adjust the tightness of the multi-wedge belt into the state that it could be flipped by 80%. Step 3: Finally lock the motor base, and install the front cover.
Need help?
Do you have a question about the MS198969 and is the answer not in the manual?
Questions and answers