Table of Contents
Advertisement
applicaTions
warning
tric shock, check work area for hidden pipes
and wires before drilling or driving screws.
Drilling in Wood, Composition Materials and
Plastic
When drilling in wood, composition materials and
plastic, select the
Start the drill slowly, gradually increasing speed as
you drill. When drilling into wood, use wood augers
or twist drill bits. Always use sharp bits. When using
twist drill bits, pull the bit out of the hole frequently
to clear chips from the bit flutes. To reduce the
chance of splintering, back work with a piece of
scrap wood. Select low speeds for plastics with a
low melting point.
Drilling in Metal
When drilling in metal, select the
operating mode. Use high speed steel twist drills
or hole saws. Use a center punch to start the hole.
Lubricate drill bits with cutting oil when drilling in
iron or steel. Use a coolant when drilling in nonfer-
rous metals such as copper, brass or aluminum.
Back the material to prevent binding and distortion
on breakthrough.
Driving Screws and Nut Running
Drill a pilot hole when driving screws into thick or
hard materials. Select the
Set the torque selector collar to the proper position
and set the speed to low. Use the proper style and
size screwdriver bit for the type of screw you are
using. With the screwdriver bit in the screw, place
the tip of the screw on the workpiece and apply firm
pressure before pulling the trigger. Screws can be
removed by reversing the motor.
Overloading
Continuous overloading may cause permanent
damage to tool or battery pack.
mainTenance
warning
always unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disas-
semble the tool, battery pack or charger.
Contact a
MILWAUKEE
ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
After six months to one year, depending on use,
return the tool, battery pack and charger to a
MILWAUKEE
®
service facility for:
• Lubrication
To reduce the risk of elec-
drill-only operating mode.
driving screws mode.
To reduce the risk of injury,
®
service facility for
• Mechanical inspection and cleaning (gears,
spindles, bearings, housing, etc.)
• Electrical inspection (battery pack, charger,
motor)
• Testing to assure proper mechanical and
electrical operation
If the tool does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a
MILWAUKEE
warning
sonal injury and damage, never immerse your
tool, battery pack or charger in liquid or allow
a liquid to flow inside them.
Cleaning
Clean dust and debris from charger and tool
vents. Keep tool handles clean, dry and free of oil
drill-only
or grease. Use only mild soap and a damp cloth
to clean the tool, battery pack and charger since
certain cleaning agents and solvents are harmful to
plastics and other insulated parts. Some of these
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia
and household detergents containing ammonia.
Never use flammable or combustible solvents
around tools.
Repairs
For repairs, return the tool, battery pack and
charger to the nearest service center, please visit
www.milwaukeetools.com.au /
www.milwaukeetools.co.nz
or contact our customer service centre
(Australia Toll Free Telephone Number
1300 645 928)
(New Zealand Toll Free Telephone Number
0800 279 624).
warning
before changing or removing accessories.
Only use accessories specifically recommend-
ed for this tool. Others may be hazardous.
For a complete listing of accessories, refer to your
MILWAUKEE ®
online to www.milwaukeetools.com.au /
www.milwaukeetools.co.nz.
To obtain a catalogue, contact your local distribu-
tor or service center.
7
®
service facility for repairs.
To reduce the risk of per-
accessories
Always remove battery pack
electric tool catalogue or go
Advertisement
Table of Contents
