JVC GY-HM660E Instructions Manual page 125

No. of Frames for
WFrame & Bit Resolution
Rate
60p, 60i, 30p 1920x1080 60i (12.0 M),
1280x720
720x480
640x360
50p, 50i, 25p 1920x1080 50i (12.0 M),
1280x720
720x576
640x360
*1 Default value for U model
*2 Default value for E model
Memo :
The settings cannot be changed during live
0
streaming.
An encoding bit rate exceeding 5.0 Mbps cannot
0
be selected when [Type] is set to "MPEG2-
TS/RTP" or "RTSP/RTP".
An encoding bit rate exceeding 5.0 Mbps cannot
0
be selected when [Type] is set to "ZIXI" and
[Latency] is set to other than "Low".
An encoding bit rate exceeding 3.0 Mbps cannot
0
be selected when [Type] is set to "ZIXI" and
[Latency] is set to "Low", or when [Type] is set to
"RTMP".
Setting values
(R: default value)
R 60i (8.0 M) (*1),
60i (5.0 M),
60i (3.0 M)
30p (8.0 M),
30p (5.0 M),
30p (3.0 M),
30p (1.5 M)
60i (8.0 M),
60i (5.0 M),
60i (3.0 M),
60i (1.5 M),
60i (0.8 M),
60i (0.3 M)
30p (3.0 M),
30p (1.5 M),
30p (0.8 M),
30p (0.3 M)
R 50i (8.0 M) (*2),
50i (5.0 M),
50i (3.0 M)
25p (8.0 M),
25p (5.0 M),
25p (3.0 M),
25p (1.5 M)
50i (8.0 M),
50i (5.0 M),
50i (3.0 M),
50i (1.5 M),
50i (0.8 M),
50i (0.3 M)
25p (3.0 M),
25p (1.5 M),
25p (0.8 M),
25p (0.3 M)
Connection Setup
For specifying the settings for connecting to the
network.
A [Wizard] screen will appear according to the
adapter connected to the rear [HOST] terminal.
Follow the instructions to perform the setting.
You can Load, Store, and Delete the settings
specified on the [Wizard] screen.
9 Wizard
A [Wizard] screen appears according to the type of
adapter that is connected to the rear [HOST]
terminal.
Follow the instructions.
9 Load
Loads the settings on the [Wizard] screen.
(A P174 [Reading the Connection Settings
File] )
9 Store
Saves the settings on the [Wizard] screen.
(A P173 [Saving the Connection Settings File] )
9 Delete
Deletes the saved settings.
(A P174 [Deleting Connection Settings] )
9 APN
For specifying APN (Access Point Name).
* This item is grayed out and cannot be selected if
APN cannot be set for the adapter attached.
Caution :
The APN setting is written into the cellular
0
adapter, not this camera recorder.
Setting a wrong APN may result in
communication failure or expensive bills from
the telecommunications company. Set the APN
correctly.
(A P152 [Connecting via Cellular Adapter] )
Metadata Server
For registering the FTP server for importing the
metadata and the path of the file to be imported.
Up to 4 settings can be registered.
125