Page 1
Truck. Ce modèle 1/10 vous initie à la conduite RC. Congratulazioni per l’acquisto di questo Ruckus Monster Truck o ® Torment Short Course Truck o K&N Torment Short Course Truck ™ ™ ECX. Questa vettura in scala 1/10 vi introdurrà nel mondo dei modelli RC.
Page 2
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product. MEANING OF SPECIAL LANGUAGE The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
0.23sec/60 degrees of travel Size 37.5 x 37.0 x 18.0mm Size 55.6 x 18 x 30mm Weight 1.41 oz (40 g) COMPONENTS • ECX ® Ruckus ® Monster Truck or Torment ™ Short Course Truck or K&N Torment Short Course Truck ™...
QUICK START Please read the entire manual to gain a full understanding of the vehicle, fine-tuning the setup and performing maintenance. 1. Read the safety precautions found in this manual. 5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to initialize.
INSTALLING THE BATTERY 1. Turn the battery clips (A) clockwise to remove the battery strap (B). 2. Install a fully charged battery. 3. Install the battery strap. 4. Turn the battery clips counterclockwise to secure the battery strap. Place foam blocks (ECX2015) in front of the battery so the weight of the battery increases rear traction or in back of the battery to increase steering response.
BINDING You must rebind when: • Different failsafe positions are desired e.g., when throttle or Binding is the process of programming the receiver to recognize the GUID steering reversing has been changed. (Globally Unique Identifier) code of a single specific transmitter. The • Binding the receiver to a different transmitter.
OPERATION • ALWAYS turn on your transmitter before you turn on the receiver • ALWAYS operate your vehicle in a wide open area. Operating the in the vehicle. Always power off the receiver before turning your vehicle in a small space or indoors can cause overheating at low transmitter off.
MAINTENANCE SETTING THE GEAR MESH The gear mesh has already been set at the factory. Setting the gear mesh is only necessary when changing motors or gears. You must remove the vehicle’s gear cover (A) to make this adjustment. Proper gear mesh (how the gear teeth meet) is important to the performance of the vehicle.
SHOCK CLEANING REAR FRONT SHOCK SHOCK Oil-filled shocks will require regular maintenance due to the oil breaking ECX1037 down or getting dirty. This maintenance should be performed after about ECX1037 ECX1043 every 3 to 5 hours of use, depending on the conditions that the vehicle is ECX1043 used in.
TROUBLESHOOTING GUIDE Problem Possible Cause Solution Battery damaged/not charged Check/change battery Short run time Motor dirty Check/clean Motor dirty Check/clean Sluggish action Bind in drivetrain Clean/adjust Vehicle battery is not charged Replace/recharge Controls reversed ST. REV or TH. REV Change switch position Motor/ESC overheat Over-geared for the driving environment Install smaller pinion on the motor...
LIMITED WARRANTY What this Warranty Covers that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the call the toll free telephone number referenced in the Warranty and Service product purchased (the “Product”) will be free from defects in materials and Contact Information section to speak with a Product Support representative.
WARRANTY AND SERVICE CONTACT INFORMATION Country of Horizon Hobby Contact Information Address Purchase Horizon Service Center servicecenter.horizonhobby.com/ (Repairs and Repair Requests) RequestForm/ productsupport@horizonhobby.com United States Horizon Product Support 4105 Fieldstone Rd of America (Product Technical Assistance) Champaign, Illinois, 61822 USA 877-504-0233 websales@horizonhobby.com Sales...
RUCKUS PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI RECOMMENDED ITEMS M3X12 EMPFOHLENE WERKZEUGE OUTILS RECOMMANDÉS ATTREZZI CONSIGLIATI M3X10 M3X10 M3X10 M3X12 2 mm 1.5 mm M3X12 M3X12 M3X12 M3X25 M3X12 M3X10 M3X10 M3X15 M3X12...
Page 14
RUCKUS PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI The slipper clutch can be adjusted using this locknut (ECX1060). Fully tighten the locknut, then loosen the nut two full turns. Die Rutschkupplung kann durch diese Stopmutter eingestellt werden (ECX1060).
TORMENT PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI M3X10 M3X10 M3X10 M3X12 M3X18 M3X12 M3X12 M3X12 M3X18 M3X25 M3X10 M3X12 M3X12 M3X10 M3X15 M3X12 M3X15 M3X10 M3X25 M3X15 M3X8 M3X12 M3X12 M3X10 RUCKUS | TORMENT | K&N TORMENT ®...
Page 16
TORMENT PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI M3X3 The slipper clutch can be adjusted using this locknut (ECX1060). Fully tighten the M2.5X8 locknut, then loosen the nut two full M2.5X4 turns.
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio Part # Description Beschreibung Description Descrizione ECX2008 Main Chassis Chassis Châssis principal Telaio principale ECX1028 Servo Saver Set Servo Saver Set Sauve servo Set salvaservo ECX2011 Cover and Rear Mount Set Abdeckung und hinterer Halter Set Capot et fixations arrières Copertura e set di montaggio posteriore...