Page 1
Short Course Truck. Dieses 1/10 Scale Model ™ öffnet Ihnen die Welt des RC Car Sports. INSTRUCTION MANUAL Nous vous félicitons pour l’achat de l’ECX Ruckus Monster Truck ® ou Torment Short Course Truck ou. Ce modèle 1/10 vous initie à...
Page 2
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product. MEANING OF SPECIAL LANGUAGE The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
Output Torque 41.66 oz (3 kg-cm) Operating Speed 0.23sec/60 degrees of travel Size 55.6 x 18 x 30mm BOX CONTENTS 2.4GHZ DIGITAL RADIO SYSTEM • ECX Ruckus Monster Truck or Torment Short Course Truck ® ® ™ • Spektrum STX2 2-CH Transmitter (SPMSTX200) ™...
QUICK START Please read the entire manual to gain a full understanding of the vehicle, fine-tuning the setup and performing maintenance. 1. Read the safety precautions found in this manual. 5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to initialize.
TRANSMITTER CONTROLS 1. Steering Wheel Controls direction (left/right) of the model 2. Throttle Trigger Controls speed and direction (forward/brake/reverse) of the model 3. ON/OFF Switch Turns the power ON/OFF for the transmitter 4. Throttle Limiting Switch Adjusts the throttle limit from 50%, 75%, and 100% 5.
BINDING You must rebind when: • Different failsafe positions are desired e.g., when throttle or Binding is the process of programming the receiver to recognize the GUID steering reversing has been changed. (Globally Unique Identifier) code of a single specific transmitter. The • Binding the receiver to a different transmitter.
OPERATION • ALWAYS turn on your transmitter before you turn on the receiver • ALWAYS operate your vehicle in a wide open area. Operating the in the vehicle. Always power off the receiver before turning your vehicle in a small space or indoors can cause overheating at low transmitter off.
MAINTENANCE SETTING THE GEAR MESH The gear mesh has already been set at the factory. Setting the gear mesh is only necessary when changing motors or gears. You must remove the vehicle’s gear cover (A) to make this adjustment. Proper gear mesh (how the gear teeth meet) is important to the performance of the vehicle.
SHOCK CLEANING REAR FRONT SHOCK SHOCK Oil-filled shocks require regular maintenance because oil breaks down ECX1037 and/or gets dirty. Perform this maintenance every 3–5 hours of use, ECX1037 ECX1043 depending on useage conditions. ECX1043 ECX1057 ECX1057 • Remove the shock from the vehicle. ECX1037 • Remove the cap from the shock body and dispose of fluid.
TROUBLESHOOTING GUIDE Problem Possible Cause Solution Battery damaged/not charged Check/change battery Short run time Motor dirty Check/clean Motor dirty Check/clean Sluggish action Bind in drivetrain Clean/adjust Vehicle battery is not charged Replace/recharge Controls reversed ST. REV or TH. REV Change switch position Motor/ESC overheat Over-geared for the driving environment Install smaller pinion on the motor...
LIMITED WARRANTY What this Warranty Covers that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the call the toll free telephone number referenced in the Warranty and Service product purchased (the “Product”) will be free from defects in materials and Contact Information section to speak with a Product Support representative.
WARRANTY AND SERVICE CONTACT INFORMATION Country of Horizon Hobby Contact Information Address Purchase Horizon Service Center servicecenter.horizonhobby.com/ (Repairs and Repair Requests) RequestForm/ productsupport@horizonhobby.com United States Horizon Product Support 1608 Interstate Drive of America (Product Technical Assistance) Champaign, Illinois, 61822 USA 877-504-0233 websales@horizonhobby.com Sales...
RUCKUS PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI The slipper clutch can be adjusted using this locknut (ECX1060). Fully tighten the locknut, then loosen the nut two full turns. Die Rutschkupplung kann durch diese Stopmutter eingestellt werden (ECX1060).
TORMENT PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI M3X10 M3X10 M3X10 M3X12 M3X18 M3X12 M3X12 M3X12 M3X18 M3X25 M3X10 M3X12 M3X12 M3X10 M3X15 M3X12 M3X15 M3X10 M3X25 M3X15 M3X8 M3X12 M3X12 M3X10 RUCKUS | TORMENT ®...
Page 15
TORMENT PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI M3X3 The slipper clutch can be adjusted using this locknut (ECX1060). Fully tighten the M2.5X8 locknut, then loosen the nut two full M2.5X4 turns.
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio Part # Description Beschreibung Description Descrizione ECX2008 Main Chassis Chassis Châssis principal Telaio principale ECX1028 Servo Saver Set Servo Saver Set Sauve servo Set salvaservo Copertura e set di montaggio ECX2011 Cover and Rear Mount Set Abdeckung und hinterer Halter Set...
Startup Tool Set Werkzeug Set Set d’outils de démarrage Set attrezzi start up ECX1061 Screw Set (64) ECX Blechschraubenset (64 Stk) Set de vis (64) Set viti (64) ECX1095 Aluminum Shock Set Front: ECX Aluminium-Dämpferset vorne Set d’amortisseurs avant en aluminium Set ammortizzatore ant.