Sharp DM-FX1 Service Manual page 16

DM-FX1
66 04
06 Confidential
communication
password print
07 Image memory content
output
08 Voice message send
<Not used>
10 Image memory clear
G The following signals are sent to the line and the main body speaker.
Display/Key operation
<Signal send level> <Send signals>
0db: Signals are 01: No signal (CMLON)
sent in 0db. 02: 33600bps (V34)
Soft SW: Signals 03: 31200bps (V34)
are sent in the 04: 28800bps (V34)
level set with the 05: 26400bps (V34)
soft SW. 06: 24000bps (V34)
07: 21600bps (V34)
08: 19200bps (V34)
09: 16800bps (V34)
10: 14400bps (V34)
11: 12000bps (V34)
12: 9600bps (V34)
13: 7200bps (V34)
14: 4800bps (V34)
15: 2400bps (V33)
16: 14400bos (V33)
17: 12000bps (V33)
G The send signals are as follows:
01: No signal is sent.
26: 7eH flag signal
27, 28, 30: Tone signal
31: Pseudo ringer sound (With the On-hook key pressed)
32: Voice message silent <Not used>
33: Ring back tone silent <Not used>
34: Dial pulse make
Under the state where dial pulses can be sent to the line, the make state is
kept.
35: Dial pulse break
Under the state where dial pulses can be sent to the line, the break state is
kept.
Other than the above: FFH
G The signal send level is selectable between 0db or the soft SW set value.
Since, however this setup is not required for pseudo ringer sound, voice
message (silent), ring back tone (silent), and dial pulse make/break., the
selection menu does not appear. (For 01, 31 to 35, selection between 0db and
the soft SW set value cannot be made.)
G Signal send is continued until an interruption command is outputted.
G The signal send level is returned to the soft SW set value before execution of
this mode when this mode is terminated.
Used to print the currently set confidential communication password.
Used to print all image data stored in the image memory. The following
image data are also outputted.
G Image data received in a confidential communication remote send image data
read in the memory
Note: Image data are cleared after being outputted.
Used to send the voice reply message.
<Sound volume setup>
LARGE: Signals are sent
in the LARGE sound
volume level.
Soft SW: Signals are sent
in the level set with the
soft switch 70-1.
Used to clear all data stored in the image memory.
The following data are also cleared.
• Image data received in confidential communication
• The management table is also initialized.
5 – 4
18: 14400bps (V17)
19: 12000bps (V17)
20: 9600bps (V17)
21: 7200bps (V17)
22: 9600bps (V29)
23: 7200bps (V29)
24: 4800bps (V27ter)
25: 2400bps (V27ter)
26: 300bps (FLAG)
27: 2100Hz (CED)
28: 1100Hz (CNG)
29: 300bps (V21)
30: 2100Hz (ANSam)
31: Pseudo ring sound
32: Voice message silent
33: Ring back tone silent
34: Dial pulse make
35: Dial pulse break
<Message>
1: "Wait for a moment."
2: "No one is around the phone. For
FAX send, please press the START button.
(FAX/TEL reply message)
3: Reserved sound