Advertisement
Pr.
Name
Home position return
1284
creep speed
Home position shift
1285
amount lower 4 digits
Home position shift
1286
amount upper 4 digits
Travel distance after
1287
proximity dog ON lower
4 digits
Travel distance after
1288
proximity dog ON
upper 4 digits
Home position return
1289
stopper torque
Home position return
1290
stopper waiting time
Position control
1292
terminal input selection
Roll feeding mode
1293
selection
Position detection lower
1294
4 digits
Position detection
1295
upper 4 digits
Position detection
1296
selection
Position detection
1297
hysteresis width
Second position control
1298
gain
Second pre-excitation
1299
selection
1300 to
Communication option parameters
1343
P/PI control switchover
1348
frequency
Emergency stop
1349
operation selection
1350 to
Communication option parameters
1359
Starting times lower 4
1410
digits
Starting times upper 4
1411
digits
Motor induced voltage
1412
constant (phi f)
exponent
Second motor induced
1413
voltage constant (phi f)
exponent
1442
IP filter address 1
(Ethernet)
1443
IP filter address 2
(Ethernet)
1444
IP filter address 3
(Ethernet)
1445
IP filter address 4
(Ethernet)
1446
IP filter address 2 range
specification (Ethernet) 0 to 255, 9999
1447
IP filter address 3 range
specification (Ethernet) 0 to 255, 9999
1448
IP filter address 4 range
specification (Ethernet) 0 to 255, 9999
1459
Clock source selection 0 to 2
Load characteristics
1480
measurement mode
Load characteristics
1481
load reference 1
Load characteristics
1482
load reference 2
Load characteristics
1483
load reference 3
Load characteristics
1484
load reference 4
Load characteristics
1485
load reference 5
Load characteristics
1486
maximum frequency
Load characteristics
1487
minimum frequency
Upper limit warning
1488
detection width
Lower limit warning
1489
detection width
Upper limit fault
1490
detection width
Lower limit fault
1491
detection width
Load status detection
signal delay time / load
1492
reference measurement
waiting time
1499
Parameter for manufacturer setting. Do not set.
Pr.CLR Parameter clear
ALL.CL All parameter clear
Downloaded from
ManualsNet.com
Setting
Initial
Pr.
range
value
Err.CL Fault history clear
0 to 10Hz
0.5Hz
Pr.CPY Parameter copy
Pr.CHG Initial value change list ―
0 to 9999
0
IPM
0 to 9999
0
AUTO Automatic parameter
Pr.Md Group parameter setting (0, )1, 2
0 to 9999
2048
Differs according to capacities.
• 6%: FR-A820-00046(0.4K), 00077(0.75K) and FR-
0 to 9999
0
• 4%: FR-A820-00105(1.5K) to 00250(3.7K) and FR-
0 to 200%
40%
• 3%: FR-A820-00340(5.5K), 00490(7.5K) and FR-
• 2%: FR-A820-00630(11K) to 03160(55K) and FR-
0 to 10s
0.5s
• 1%: FR-A820-03800(75K) or higher and FR-A840-
0, 1
0
For FR-A820-03160(55K) or lower and FR-A840-
01800(55K) or lower
0, 1
0
For FR-A820-03800(75K) or higher and FR-A840-
02160(75K) or higher
0 to 9999
0
For FR-A820-00490(7.5K) or lower and FR-A840-
00250(7.5K) or lower
0 to 9999
0
For FR-A820-00630(11K) or higher and FR-A840-
00310(11K) or higher
Differs according to capacities.
0 to 2
0
• 4%: FR-A820-00490(7.5K) or lower and FR-A840-
0 to 32767
0
• 2%: FR-A820-00630(11K) to 03160 (55K) and FR-
• 1%: FR-A820-03800(75K) or higher and FR-A840-
-1
-1
0 to 150s
25s
Differs according to the voltage class. (200 V class/400
0, 1
0
V class)
The setting is available only when a Vector control
compatible option is installed. To check the availability
of the parameter for each option refer to the Instruction
Manual (Detailed).
0 to 400Hz
0Hz
The parameter number in parentheses is the one for
use with the LCD operation panel and parameter unit.
0, 1, 10, 11
0
Differs according to types. (FM type/CA type)
The setting is available only with the CA type.
The setting value "60" is only available for Pr.178, and
"61" is only for Pr.179.
The setting values "92, 93, 192, and 193" are only
0 to 9999
0
available for Pr.190 to Pr.194.
Simple mode parameters. (Initially set to the extended
mode.)
0 to 9999
0
Parameters for CC-Link IE TSN communication.
When Pr.160="9999", only the simple mode
0 to 2, 9999
9999
parameters and the parameters for CC-Link IE TSN
communication are displayed.
The setting is available when the PLC function is
enabled.
0 to 2, 9999
9999
The initial value after All parameter clear.
0 to 255
0
0 to 255
0
0 to 255
0
0 to 255
0
9999
9999
9999
0
0, 1, (2, 3, 4, 5,
81, 82, 83, 84,
0
85)
0 to 400%,
9999
8888, 9999
0 to 400%,
9999
8888, 9999
0 to 400%,
9999
8888, 9999
0 to 400%,
9999
8888, 9999
0 to 400%,
9999
8888, 9999
60/50Hz
0 to 590Hz
0 to 590Hz
6Hz
0 to 400%, 9999 20%
0 to 400%, 9999 20%
0 to 400%, 9999 9999
0 to 400%, 9999 9999
0 to 60s
1s
(0, )1
0
(0, )1
0
search engine
Setting
Name
range
(0, )1
0
(0, )1 to 3
0
―
IPM initialization
0, 3003
0
―
―
setting
0
A840-00023(0.4K), 00038(0.75K)
A840-00052(1.5K) to 00126(3.7K)
A840-00170(5.5K), 00250(7.5K)
A840-00310(11K) to 01800(55K)
02160(75K) or higher
00250(7.5K) or lower
A840-00310(11K) to 01800 (55K)
02160(75K) or higher
Initial
value
PARAMETER LIST
19
Advertisement
