Page 1
INSTRUCTION MANUAL 17”/19” LCD VIDEO MONITOR LCM-171 / LCM-191 Model OAM00045REV.00 IMU171191 Please read this manual thoroughly before use and keep for future reference.
1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Page 3
those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore normal operation. E. If the product has been dropped or the cabinet has been damaged. If the product exhibits a distinct change in performance, indicating a need for service.
CAUTION The power supply cord is used as the main disconnect device, ensure that the socket-outlet is Located / installed near the equipment and is easily accessible. ATTENTION Le cordon d`alimentation est utillsé comme interrupteur général. La prise de courant doit être située ou installée à...
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Remove the package cover and place the product on a flat and secure surface or in the installation location. Check whether all the flowing device and accessories are included with the main system. TFT-LCD MONITOR USER MANUAL AC POWER ADAPTOR PSU is built in the back of monitor POWER CORD VGA CABLE...
REAR PANEL CONTROL 1. DC 12V Power IN 2. RGB IN RGB signal input 3. VIDEO 1(AV1) IN Composite signal input for AV1 4. VIDEO 1(AV1) OUT Composite looping output for AV1 5. VIDEO 2(AV2) IN Composite signal input for AV2 6.
REMOTE CONTROLLER 1. POWER Turn the power ON or OFF. There will be a few second time delay before the display appears. 2. MUTE Mute the sound. 3. VIDEO1 Select Video1 source. 4. VIDEO2 Select Video2 source. 5. S-VIDEO Select S-Video source. 6.
KEY FUNCTIONS 1. MENU/EXIT Activate and exit the OSD. 2. ▼ Move the OSD menu. 3. AUTO / ▲ Move the OSD menu and auto adjustment of PC source. 4. ◀ (VOL-) Decrease the level of volume and move the previous menu. 5.
Page 11
OSD MENU DESCRIPTION MENU SELECTION 1. Press the MENU button to access the Main menu. 2. Use the arrow buttons to highlight a selection. 3. Press the OK or button to select an item. 4. Use the arrow buttons to highlight a selection. 5.
Page 12
1. Press the MENU/EXIT button and then ▲/▼ button to select the PICTURE menu. 2. Press the OK or ▶ button and then ▲/▼ button to select the adjustment item you need. 3. Press the OK or ▶ button to active the item. ex) If you select the BRIGHTNESS, then the below picture appears on the bottom of screen.
Page 13
■ D. RGB SETUP MENU 1. Press the MENU button and then ▲/▼ button to select the RGB SETUP menu. 2. Press the ▶ button and then ▲/▼ button to select the adjustment item you need. 3. Press the ▶ button to active the item. 4.
Page 14
1. Press the MENU button and then ▲/▼ button to select the FUNCTION menu. 2. Press the ▶ button and then ▲/▼ button to select the adjustment item you need. 3. Press the ▶ button to active the item. 4. Press the MENU button to move to the previous menu. LANGUAGE: Select the language: English, French, German, Italian, Spanish.
D-SUB CONNECTOR PIN ASSIGMENTS PIN ASSIGNMEN Pin No. Pin Name Pin No. Pin Name RED VIDEO GREEN VIDEO SIGNAL CABLE DETECT BLUE VIDEO GROUND GROUND SDA (for DDC) GROUND H-SYNC RED GROUND V-SYNC GREEN GROUND SCL (for DDC) BLUE GROUND TROUBLESHOOTING GUIDE Troubleshooting Troubleshooting Tip...