Wall Control Installation - Genie GPS-IC Owner's Manual

4

WALL CONTROL INSTALLATION

...
Power cord must be unplugged before attaching
wires. Be sure wire ends do not touch each other
or other terminals.
20
• Use of any other wall control will cause the
light not to work and could cause door to
operate by surprise.
• Cut or pinched wires can cause door operator
to malfunction. Drive staples just tight enough
to hold wire.
1. Run wire from power head to wall control.
• Place the wall control:
– In sight of door.
– At least 5 feet from floor, so small children can
not reach it.
– Away from moving parts of door and
door hardware.
• Use staples to fasten wire to ceiling and wall.
2. Remove 1/2" insulation from each wire
(Fig. 3-6)(pg. 19).
3. Attach wires to terminals (Stealth Fig. 4-1a)
(MAX Fig. 4-1b).
• Loosen, but Do Not remove screw from terminal.
For Stealth.
– Connect striped wires to terminal "2" on power
head and "B" on wall control.
– Connect white wire to terminal "1" on power
head and "W" on wall control.
For MAX.
– Connect striped wires to terminal "1" on power
head and "B" on wall control.
– Connect white wire to terminal "2" on power
head and "W" on wall control.
4. Mount wall control (Fig. 4-2).
• Use two pan head screws.
5. Mount entrapment warning label.
• Remove protective backing and stick near
wall control.
• Use tacks or staples to permanently mount Label.
• Make sure everyone reads and follows WARNINGS.
Vacation Locking Switch
– LOCK disables controls after door is completely closed
– UNLOCK allows controls to work normally
Independent Light Control
– Controls door operator lights from inside garage
– Energy-Saver shut-off turns off light 5 minutes after
door activation
NOTE: Additional wall controls are available from your
dealer. ONLY ONE OF YOUR WALL CONTROLS MAY BE THE
LIGHTED TYPE. If you have a lighted wall control, all your
additional controls must be un-lighted. More than one
lighted wall control per operator will cause a malfunction.
WARNING
CAUTION
FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM
Power head
1
terminals
2
3
W1
4
B2
Y3
G4
MORE
1
PUSH
TO SET
OPEN
LIMITS
TMENT
2
Power
head
3
Rear view of
ferminals
power head
4
Fig. 4-1a
C SS
Power head
terminals
NEC
CLASS 2
PUSH
1
BUTTON
2
COM
NOTE:
SAFETY 3
USE ONLY WITH
BEAM
SERIES II CONTROLS
4
DO NOT
PUSH
LIMIT SET
5
UNLESS
DOOR IS
ATTACHED
6
LIMIT
SET
C SS
OPEN
CLOSE OPEN
FORCE
MORE MORE
MORE
CLOSE
FORCE FORCE
RADIO
SIGNAL
OSE OPEN
LEARN
CODE
LIMIT ADJUSTMENT
U.S. Patent No. 5,243,784
5,221,869
Front view of
power head
power head
terminals
Fig. 4-1b
Wall button
OR
#6 x 1"
pan head screws
Fig. 4-2
Lighted Button
1
– Shows system is powered
– Lights when Security Lock
2
– Goes out when Security Lock
4
Door Control Button
– Open and closes door from
3
Fig. 4-3
White
Striped
Wall
W
button
B
terminals
Back view
OR
White
Wall
B W
Striped
console
terminals
Back view
Striped
1
Wall
W
White
button
2
B
terminals
3
Back view
EITHER
Striped
1
Wall
White
console
B W
2
terminals
3
Back view
Wall console
Switch is in UNLOCK position
Switch is in LOCK position
inside garage