Related Manuals for Diginet LEDsmart+ MMDM RT
Summary of Contents for Diginet LEDsmart+ MMDM RT
- Page 1 Setup Functions Guide MMDM/RT Rotary Dimmer with built in on / off switch and multi-way control DIGINET.NET.AU...
-
Page 2: Dimmer Setup
Setup Functions - Rotary Dimmer/Switch Dimmer Setup The LEDsmart rotary dimmer has a number of useful functions which can easily be set up by entering setup mode and following four easy steps. It is recommended that the MINIMUM BRIGHTNESS is always set up. The other settings are optional, depending on the dimmer application. - Page 3 Setup Functions - Rotary Dimmer/Switch A1: Dimmer has been powered up via mains 240Vac for LESS THAN 15 MINUTES Step 1 Press and hold the dimmer rotary shaft for 10 seconds Note: Connected lights will dim up or down, this is normal Step 2 The white LED Indicators will blink ON/OFF twice per second.
- Page 4 Setup Functions - Rotary Dimmer/Switch B: Setting Minimum Brightness The minimum brightness level provided by the dimmer can be set to suit specific lamps and/or customer requirements. For the majority of lamps a minimum level as low as 0% can be set if required. However, some lamps can become unstable at low dimming levels, in particular CFL’s.
- Page 5 Setup Functions - Rotary Dimmer/Switch C: Setting Maximum Brightness The maximum brightness level provided by the dimmer can be set to suit customer requirements. Note that when lamps are dimmed near to full brightness, it is difficult to see changes in dimming level. Therefore, when setting up maximum brightness, it is recommended that the lamp is slowly dimmed up to a point where no further changes in brightness can be seen, and the maximum level set at this point.
- Page 6 Setup Functions - Rotary Dimmer/Switch D: Setting the Kick Start Feature The ‘kick-start’ feature is only required to be enabled when dimming loads such as compact fluorescent lamps. These lamps require the dimmer output to be set to 50% for 0.2 of a second when the lamp is turned on. This ensures the lamp strikes successfully.
- Page 7 Setup Functions - Rotary Dimmer/Switch E: Setting Off State Indication When the dimmer is switched off, the white LED indicators in the dimmer can be set to glow on or turn off. By Default, the white LED indicators are set to glow on when the dimmer is turned off. To set the LED indicators to turn off when the dimmer is off, follow the steps below.
- Page 8 Setup Functions - Rotary Dimmer/Switch F: Setting Separate Switch Mode The dimmer is designed to operate as a combined switch and dimmer, taking up only one gang in a wall plate. However, some lamps (for example, non-dimmable CFL’s) can flicker when switched OFF by pressing the rotary dial. In these cases it is recommended that the dimmer is used in ‘Separate Switch Mode’...
- Page 9 Setup Functions - Rotary Dimmer/Switch G: Setting Toggle / Memory Step 1 Enter into the dimmer Setup Mode - See PART A Step 2 Click the dimmer rotary shaft 7 times Step 3 LED will blink 7 times If the memory dimmer function is currently Disabled, lamp(s) connected to the dimmer will now turn OFF b.
- Page 10 Setup Functions - Rotary Dimmer/Switch H: Setting Multimate™ Dimmer Mode Step 1 Enter into the dimmer Setup Mode - See PART A Step 2 Click the dimmer rotary shaft 8 times Step 3 LED will blink 8 times If the MultiMate™ function is currently Disabled, lamp(s) connected to the dimmer will now turn OFF b.
- Page 11 Setup Functions - Rotary Dimmer/Switch I: Resetting to Factory Defaults Step 1 Enter into the dimmer Setup Mode - See PART A Step 2 Click the dimmer rotary shaft ten times Step 3 The dimmer will automatically exit Setup Mode once reset...
- Page 12 96-112 Gow Street Padstow NSW 2211 Contact General Enquiries: 1300 95 DALI (3254) or sales@diginet.net.au Technical Services: 1300 95 3244 or support@diginet.net.au Fax: 1300 95 3257 Diginet is a brand of the Gerard Lighting Group Version: Issue 1 July 2016...