Rear Terminals; Vcr/Dvd Switching - Sharp DV-NC200S Operation Manual

Vcr/dvd combination
Table of Contents

Advertisement

Display During Operation

Rear Terminals

21. MAIN (AC power cord)
Connect to a standard AC plug.
22. COMPONENT VIDEO OUT Jacks (DVD only)
Connect optional component video cable here through the
component video input jacks of a TV.
23. COAXIAL DIGITAL AUDIO OUT Jack (DVD only)
Connect to a compatible Dolby Digital receiver.
Use to connect to a Dolby Digital, DTS, or MPEG decoder.
24. AUDIO OUT Jacks (Analog Left/Right) (DVD only)
Connect to the audio input jacks of A/V-compatible TV.
25. S-VIDEO OUT Jack (DVD only)
Use the S-video cable to connect this jack to the S-video input
jack on your A/V-compatible TV or wide screen TV for a higher
quality picture.
Because this product is a combination of a VCR and a DVD player,
you must select first which component you wish to operate with
OUTPUT.
VCR MODE
Press VCR on the remote control.
(Verify that the VCR OUTPUT indicator is lit.)
DVD MODE
Press DVD on the remote control.
(Verify that the DVD OUTPUT indicator is lit.)
Hint
• Pressing only OUTPUT on the front panel DOES NOT switch the
mode of the remote control. You MUST select the correct mode
on the remote control.
In the wrong mode, the VCR/DVD does not respond to your com-
mands correctly. Before starting your desired operation, select
the correct mode by following the instruction (
) under the subject heading.
VCR
DVD
press
first.
1
2
3
4
5
6
7
8
9
0
+10
PLAY
STOP
VCR/DVD COMBINATION
NA527AD
Downloaded from:
http://www.usersmanualguide.com/
No disc inserted / cannot read disc
Appears when the disc tray is opening.
Appears when the disc tray is closing.
21
22
23
24
25
VCR/DVD S
VCR
DVD
press
1
2
3
4
5
6
7
8
9
0
+10
PLAY
STOP
VCR/DVD COMBINATION
NA527AD
26
27
26. EURO AV1 (TV) Terminal
Use the scart cable to connect this terminal to the 21-pin scart
terminal on your A/V-compatible TV or wide screen TV for a best
quality picture.
27. EURO AV2 (DECODER) Terminal (VCR only)
Use the scart cable to connect this terminal to the 21-pin scart
terminal on your decoder.
28. RF OUT Jack
Use the supplied Round Coaxial cable to connect this jack to the
AERIAL jack on your TV.
29. AERIAL Jack
Connect your antenna, cable box or direct broadcast system.
WITCHING
D V - N C 2 0 0
OPERATE
ST OP/
PULL OPEN
REW
FF
EJECT
PLA Y
REC
TIMER
OUTPUT
VCR
or
first.
– 7 –
Appears when a disc is loaded on the
disc tray.
Appears when a disc or tape is being
played back.
Appears when the PBC function is acti-
vated. (Video CD playback only. Refer
to page 5.)
A E R I A L
R F O U T
28 29
OPEN/CLOSE
OUTPUT
C H
V C R
D V D
ST OP
PLA Y
(TRACKING)
VCR button
DVD button
DVD
DVD OUTPUT
indicator
OUTPUT button
VCR OUTPUT
indicator
OPERATE
OPEN/CLOSE
SETUP
DISPLAY
EJECT
SUBTITLE
ANGLE
AUDIO
MARKER
VCR
DVD
MODE
ZOOM
TITLE
MENU
ENTER
RETURN
REPEAT
1
2
3
A-B REPEAT
6
4
5
7
8
9
SKIP
CLEAR/C-RESET
0
+10
REV
FWD
PLAY
REC/OTR
STILL/PAUSE
STOP
DIRECT SKIP
TAPE SPEED
TIMER
QUICK-FIND
/SYSTEM
ON/OFF
SLOW
GAMMA
SEARCH MODE
CH
VCR/DVD COMBINATION
NA545FD
EN

Advertisement

Table of Contents
loading

This manual is also suitable for:

Dv-nc200sb

Table of Contents