Specifications
The specifications of the projector are as follows.
Model No.
Power supply
Power consumption
Size
DLP chip
Display system
Number of pixels 786 432 pixels (1 024 x 768 dots)
Electric zoom
Lens
Electric focus
Light source
Light output
*3
Contrast ratio
*3
Projected image size
Screen aspect ratio
Projection method
Card slot
Outer case
Outer color
Weight
Noise level
*3
Temperature
Operating
*5
environment
Humidity
Power supply
Operating range
Remote
control
Weight
Dimensions
*1 When the [SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO], the network function (both wireless LAN and wired LAN)
cannot be used in standby mode.
*2 When the [SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [NETWORK], the network function while in standby mode is
restricted to the projector operations via wired LAN using the Wake on LAN function.
*3 Measurement, measuring conditions and method of notation all comply with ISO/IEC 21118:2012 international standards.
*4 Operations of the Panasonic SD memory card up to capacity of 2 GB and Panasonic SDHC memory card up to capacity of 32 GB are confirmed.
*5 The operating environment temperature should be between 0 °C (32 °F) and 35 °C (95 °F) when using the projector at elevations between 1 000 m
(3 281') and 2 700 m (8 858') above sea level.
When using the projector at elevations lower than 1 000 m (3 281') above sea level, and the operating environment temperature becomes 35 °C
(95 °F) or higher, the light output may be reduced to protect the projector. When using the projector at elevations between 1 000 m (3 281') and 2
700 m (8 858') above sea level, and the operating environment temperature becomes 30 °C (86 °F) or higher, the light output may be reduced to
protect the projector.
140 - ENGLISH
Chapter 7 Appendix — Specifications
120 V ~ (120 V alternating current), 50 Hz/60 Hz
240 W (2.3 A)
In standby mode (when [STANDBY MODE] is set to [ECO]): 0.4 W
In standby mode (when [STANDBY MODE] is set to [NETWORK]): 0.5 W
In standby mode (when [STANDBY MODE] is set to [NORMAL] and the fans are stopping): 12 W
14.0 mm (0.55") (aspect ratio 4:3)
1-unit DLP chip, DLP type
1.3 to 2.9:1
F = 2.0 to 2.7
f = 15.2 mm to 32.7 mm
Laser diode (Maximum output: 36 W x 2, Wavelength: 452 - 458 nm)
2 000 lm (ANSI)
1 000:1
0.76 m (30") to 5.08 m (200")
4:3
[FRONT]/[REAR]
(On/off of vertical flip can be set with [VERTICAL FLIP])
SD card slot
x 1 (supports SDHC memory card)
*4
Molded plastic
PT-JX200FBU: Black, PT-JX200FWU: White
4.6 k] (10.14 lbs.)
When [LIGHT POWER] is set to [NORMAL]: 33 dB
When [LIGHT POWER] is set to [ECO]: 30 dB
0 °C (32 °F) to 40 °C (104 °F)
10 % to 80 % (no condensation)
DC 3 V (AAA/R03 or AAA/LR03 battery x 2)
Within approx. 7 m (22'11") (when operated directly in front of signal receiver)
63 ] (2.2 ozs.) (including batteries)
Width: 44 mm (1-23/32"), Height: 105 mm (4-1/8"), Depth: 20.5 mm (13/16")
PT-JX200FBU/PT-JX200FWU
*1
*2