Subscribe to Our Youtube Channel
Related Manuals for Barco R9040014
Summary of Contents for Barco R9040014
- Page 1 BARCO PROJECTION SYSTEMS REALITY R9040014 INSTALLATION MANUAL Date : Rev. : Art. No. : 16032001 R5976257...
- Page 2 Produced by BARCO NV, March 2001. All rights reserved. Trademarks are the rights of their respective owners. BARCO n.v./Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visite Barco at the web : http://www.barco.com Printed in Belgium...
-
Page 3: Table Of Contents
Table of contents TABLE OF CONTENTS SAFETY INSTRUCTIONS..................... 1-1 Safety Instructions .............................. 1-1 Notice on Safety ....................................1-1 installation INSTRUCTIONS ................................1-1 OWNER’S RECORD ................................... 1-1 Safety indication on the product ..............................1-1 Safety Warning ....................................1-2 FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) ....................... 1-2 On Safety ...................................... - Page 4 Raster centering ....................................7-5 CRT Projection Angle Adjustment ..............................7-6 Scheimpflug Adjustment (Diagonal image focusing) ........................7-7 MESSAGES, WARNINGS AND FAILURES ................ 8-1 BARCO CEILING MOUNT SUPPORT ................. A-1 Introduction ....................................... A-1 Contents of the installation guidelines ............................. A-1 GAMMA CORRECTIONS....................B-1 Gamma corrections ............................
-
Page 5: Safety Instructions
Safety Instructions SAFETY INSTRUCTIONS Safety Instructions Notice on Safety INSTALLATION INSTRUCTIONS OWNER’S RECORD PART NUMBER : DEALER : Safety indication on the product... -
Page 6: Safety Warning
Safety Instructions Safety Warning FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) On Safety WARNING FOR THE CUSTOMERS A. Mains lead (Power cord) with CEE 7 plug B. Power cord with ANSI 73.11 plug... -
Page 7: Caution On Fire Hazard
Safety Instructions Caution on Fire Hazard On installation On servicing Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: Replacement parts Safety check On cleaning... -
Page 8: On Repacking
Safety Instructions On repacking On illumination... -
Page 9: Packing And Dimensions
Packing and dimensions PACKING AND DIMENSIONS Unpacking Unpacking To open the banding around the carton, pull out the clip as shown below : Take the projector out of its shipping carton. Be aware of the weight of the projector : 85 kg (188 lbs). To carry the projector, 2 persons are needed. -
Page 10: Projector Dimensions (In Mm)
Packing and dimensions Projector dimensions (in mm) 5976257 BARCOREALITY 909 16032001... -
Page 11: Installation Guidelines
Installation guidelines INSTALLATION GUIDELINES Installation Guidelines Ambient Temperature Conditions Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. Operation temperature : Max. -
Page 12: Which Screen Type
The BARCOREALITY 909 is designed for projecting an image width from 1.4m (4.6') to 6m (20') with an aspect ratio of 4 to 3. It leaves the BARCO factory, adjusted as a ceiling/front projector for a screen width of 2.4m (7.8'). Changing the image size from the factory preset size requires a realignment of the projector. -
Page 13: Projector Configuration
Installation guidelines Projector Configuration Which configuration can be used. The projector can be installed to project images in four different configurations (image 1): rear/ceiling, rear/table, front/ceiling or front/table. Rear/Ceiling Rear/Table Front/Ceiling Front/Table image 1 Positioning the Projector The projector should be installed perpendicular with the screen on a distance PD and water leveled in both directions. The mounting positions shown in following images are shown for a nominal lens position. -
Page 14: Lens Formulas
Installation guidelines Lens formulas Following lens formulas should be used to calculate the ideal projection distance: In metric: PD[m] = 1.311 x SW[m] + 0.33 A[cm] = 11.3 x SW[m] - 28.188 In inch: PD[inch] = 1.311 x SW[inch] + 13.029 A[inch] = 0.113 x SW[inch] - 11.098 Battery installation in the RCU. -
Page 15: Installation Setup
Warning Risk of electric shock ! The installation should only be done by BARCO authorized service personnel Opening the top cover During the projector setup and installation it is necessary to open the top cover. Follow the procedure described below : Turn the locking screw with a screwdriver counter clockwise (Image 1). -
Page 16: Removing The Top Cover
Installation setup Removing the top cover During some installations, it will be convenient to remove the top cover from the projector totally. Proceed as follows : Disengage the left axis A (Image 1) by pulling it out of the hinge. Image 1 Proceed the same way for the right axis. -
Page 17: Scan Adaptation
Installation setup Scan Adaptation Scan Connectors The scan connectors must be placed in the correct position which corresponds to the desired scanning configuration. To change the scanning, it is necessary to remove the projector top cover and to open the protection plate. For opening the projector's top cover, see 'Access to controls'. -
Page 18: Horizontal Scan Connectors
Installation setup Horizontal Scan connectors When changing the horizontal scan, insure that all three connectors are set in the same position. The configuration of each connector is depending on its orientation i.e. on the position of the strap (grey wire). Vertical Scan connectors When changing the vertical scan, insure that all three connectors are set in the same position. - Page 19 Installation setup Scan position check To check the scan position i.e. the orientation of the scan connectors proceed as follows: This procedure can only be done after power (mains) connection. So, first continue with the projector setup and the connections and then return to this procedure.
- Page 20 Installation setup 5976257 BARCOREALITY909 16032001...
-
Page 21: Ac Power Connections
AC Power Connections AC POWER CONNECTIONS AC Power cord AC Power Cord Connection Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the rear side of the projector. U uv†... -
Page 22: Ac Power
AC Power Connections Power cord with an ANSI 73.11 plug The wires of the delivered mains lead (power cord) are colored in accordance with the following code : Yellow and Green Ground (Earth). White Neutral. Black Live. AC Power The power voltage The power input voltage is autoranging between 100V (-10%) and 240V (+6%) Fuses Fuses... -
Page 23: Switching On The Projector
AC Power Connections Switching on the projector Switching on The projector is switched ON and OFF using the power (mains)switch. Pressed : ON Not pressed : OFF W ‚€ à !!"ÃW ,QRP &$Ã6 €ƒ 2 )) )UHT $%ÃC“ P O W E R / M A IN S power switch Stand by indication lamp : No light up : projector switched off... -
Page 24: Start Up In Stand By Mode
AC Power Connections Start up in Stand by Mode The projector starts up in stand by. Press a digit key corresponding to the desired source or press STBY key. The projector displays the selected source or the warm up cycle message. When this warm up message appears on the screen, handle as described in 'Start up in Operational Mode'. -
Page 25: Source Connections
Source Connections SOURCE CONNECTIONS Input Sources Input facilities The following source types can be connected to the inputs : Composite Video S-Video RGBS or RGsB RGB3S or RG3sB (R-Y)Y(B-Y)S or (R-Y)Ys(B-Y) [component input] (R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) [component input] Only available when the optional decoder is installed. This dev ice complies with part 15 of the FCC rule s. -
Page 26: Connecting A Composite Video Source To Port 1
Source Connections Connecting a Composite Video source to Port 1 Composite video signals coming from a VCR, OFF air signal decoder and so on can be connected to Port 1. 75 W Termination Switch for Video Terminate the video input of the projector using the 75 Ω switch next to the video input, when the projector operates alone or when the projector is the last unit in a loop-through configuration. - Page 27 Source Connections Pin assignment for the 4 pin connector '(6&5,37,21 &+$5$&$&7(5,67,& QDIÃ @6SUCÃBSPVI9ÃGVHDI6I8@ Ã Ã Ã QDIÃ!Ã @6SUCÃBSPVI9Ã8CSPHDI6I8@ Ã QDIÃ" GVHDI6I8@ÃTDBI6GÃ` "q7 QQÃ QDIÃ# 8CSPHDI6I8@ÃTDBI6GÃ8 "€W "q7 QQÃ How to select S-Video (or composite Video) source: Select the S-Video input by pressing the numeric button 2 on the RCU or the local keypad. 5976257 BARCOREALITY 909 16032001...
-
Page 28: Connecting A Rgb Analog Source To Port 3
Source Connections Connecting a RGB Analog source to Port 3 Connect a RGB Analog signal via an interface (e.g. RGB 120MHz interface, part number 98 26570) to Port 3: RGB analog input with automatic sync detection (Separate H and V sync inputs, with composite sync input or with sync signals on green). T h is d ev ice c omplies with par t 1 5 of See installation instructions before connecting to the supply. - Page 29 Source Connections Location of the second RGB Module The second RGB Module is inserted in the 4th slot of the main frame (Image 1). image 1 How to remove the second RGB Module. 1. Press the module lock (Image 2) 2.
-
Page 30: Connecting A Component Video Source To Port 4/5
Select the RGB analog sourcet by pressing the numeric button 4 or 5 on the RCU or the local keypad. Interfaces to be used: An interface is recommended when connecting a computer and local monitor to the projector. BARCO provides the following interfaces : 1. Universal Analog Interface. 2. RGB 120 MHz Analog Interface. -
Page 31: Connecting A Rgb Analog Source With Tri-Level Sync To Port 4/5 (Option)
Source Connections Connecting a RGB Analog source with Tri-level sync to Port 4/5 (option) RGB analog input terminals with Tri-level sync input or with Tri-level sync on green can be connected to the projector via Port 4/5. The projector detects automatically where the sync signal is located. This feature requires an optional Tri-Level Sync Module - Order Number R9828040. -
Page 32: Communication Connections
Source Connections Communication connections Communication facilities : 1. RS232 in / RS232 out. 2. Comm port for communication with peripheral (switchable between PPM and RC5) 3. RC for remote cable connection with the RCU. 4. MOUSE to control a PC with the projector remote control. 5. -
Page 33: Installation Adjustment Mode
Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks to enter your password. (Password protection is only available when the password strap on the contoller module is ON. (Contact a BARCO authorized technician when no password is requested during the adjustment procedure and password protection is desired.) -
Page 34: Overview Flowchart Of The Installation Adjustment Mode
Installation Adjustment Mode Overview flowchart of the installation Adjustment mode Following flowchart gives the different submenus within the 'Installation' menu. ADJUSTMENT MODE INSTALLATION PROJECTOR DISTANCE OPTICAL LENS FOCUSING RASTER CENTERING CRT PROJECTION ANGLE ADJUSTMENT SCHEIMPFLUG ADJUSTMENTS Flowchart 1 Access to adjustments The top cover of the projector should be removed in order to gain access to the adjustments. -
Page 35: Projector Distance
Installation Adjustment Mode Projector Distance On the screen, a drawing (Projection distance 1 Menu) will be displayed together with parameters indicating a correct position. ceiling PROJECTOR DISTANCE projector PROJECTOR DISTANCE 1 screen A = C o r r e c t io n v a lu e P D = P e r p e n d ic u la r d is ta n c e b e t w e e n s c r e e n a n d p r o je c t o r S W = S c r e e n w i d t h... -
Page 36: Optical Lens Focusing
Installation Adjustment Mode Optical Lens Focusing The optical focusing procedure is performed separately for each lens. The appropriate CRT will be switched on as the user proceeds through the optical focusing adjustment sequence. Following screen will be projected for each lens : OPTICAL LENS FOCUSING 1.LOOSEN THE NUT ON THE REAR OF THE GREEN LENS,... -
Page 37: Raster Centering
Installation Adjustment Mode Raster centering The raster must be centered on the CRT faceplate of each tube, therefore, it is necessary to look into the lenses. Contrast and brightness settings during Raster centering To avoid eye discomfort while performing these adjustments, reduce the contrast and gradually increase the brightness level until the raster becomes visible behind the image. -
Page 38: Crt Projection Angle Adjustment
Installation Adjustment Mode CRT Projection Angle Adjustment The projection angle of the red and blue CRT's is dependent on the desired size of the projected image. If the centers of green, blue and red do not coincide, the CRT projection angle must be adjusted. Note Never try to correct this misalignment with the shift correction or the static convergence controls. -
Page 39: Scheimpflug Adjustment (Diagonal Image Focusing)
Installation Adjustment Mode Scheimpflug Adjustment (Diagonal image focusing) Why? With the diagonal image focusing corrections, it is possible to obtain uniform focus for the total projected image. These corrections must be repeated for each color. The Diagonal image focusing is repeated 3 times, first for green, then for red and then for blue. - Page 40 Installation Adjustment Mode 5976257 BARCOREALITY 909 16032001...
-
Page 41: Messages, Warnings And Failures
Messages, warnings and failures MESSAGES, WARNINGS AND FAILURES When selecting a new source, INPUT 01 information about this source will RGB2 WRONG Message when the entered pass- be displayed on the screen. Source Fh= 15.6 kHz PASSWORD word is wrong. number, horizontal and vertical fre- Fv= 050 Hz quencies of the displayed source. - Page 42 Messages, warnings and failures FAILURE Serial communication error be- RCVDS com- tween the RCVDS and the munication projector. error FAILURE input not valid invalid input FAILURE error in the communication between the projector and the PC. PC communica- tion error FAN FAILED projector switched off due to a fan fail.
-
Page 43: Barco Ceiling Mount Support
This appendix gives only an overview of the contents of the installation guidelines and some overview drawings. The installation guidelines for the BARCO ceiling mounting support can be ordered from BARCO. The order number: R5975693. Contents of the installation guidelines... - Page 44 Barco ceiling mount support 5976257 BARCOREALITY 909 16032001...
-
Page 45: Gamma Corrections
Gamma corrections GAMMA CORRECTIONS Gamma corrections Gamma warning ENTER Procedure for Gamma corrections To carry out the Blue Gamma Correction :ç or è é ê é ê ENTER EXIT Service ENTER é ê ç è ENTER WARNING GAMMA CORRECTION RISK OF INCORRECT BLUE GAMMA CORRECTION ADJUSTMENT OF THE PROJECTOR. - Page 46 é ê ç è Gamma corrections To carry out the Red and Blue Midlights Correction: é ê ENTER EXIT Service é ê ç è ENTER GAMMA CORRECTIONS BLUE GAMMA CORRECTION Adjust slope with é or ê Breakpoint with ç or è R&B MIDLIGHTS HTS Adjust red with é...
- Page 47 Form Approved MATERIAL SAFETY DATA SHEET Bureau Budget No. 45-R0338 MANUFACTURER'S NAME AND FSCM (Federal Supply Code for Manufacturer's) EMERGENCY PHONE NO. BARCO N.V. 32-56-368211 ADDRESS (Number, Street, City, State, and ZIP Code) Noordlaan 5 B-8520 KUURNE CHEMICAL NAME AND SYNONYMS TRADE NAME AND SYNONYMS Ethylenglycol &...
- Page 48 TRESHOLD LIMIT VALUE 100ppm EFFECTS OF OVEREXPOSURE EMERGENCY AND FIRST AID PROCEDURES CONDITIONS TO AVOID STABILITY UNSTABLE STABLE INCOMPATABILITY (Materials to avoid) HAZARDOUS DECOMPOSITION PRODUCTS CONDITIONS TO AVOID OCCUR HAZARDOUS POLYMERIZATION WILL NOT OCCUR STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED Rinse with water WASTE DISPOSAL METHOD RESPIRATORY PROTECTION (Specific type)
Need help?
Do you have a question about the R9040014 and is the answer not in the manual?
Questions and answers