IMPORTANT – Please Read and Follow! • Make sure that incoming voltage is the same as unit rating. An electric Your safety and the safety of others is very rating plate specifying voltage, frequency, wattage, amperage, and important. phase is attached to the product. •...
Page 4
• The required use of a GFI is normally related to the location of a receptacle with respect to any signifi cant sources of water or moisture. • Viking Range, LLC will warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
Specifi cations (VRI/FRI/MVRI) Integrated All Refrigerator Description MVRI 24" 24" Overall width 24" (61.0 cm) 24" (61.0 cm) Overall height (from bottom) 83-15/16" (213.2 cm) min to 84-3/4" (215.7 cm) max Overall depth from rear To front edge kickplate: 22-1/16” (56.0 cm) To front of door panel : 24-3/4”...
Page 7
Specifi cations (VFI/FFI/MVFI) Integrated All Freezer Description MVFI 18" 24" 18" 24" Overall width 18" (45.7 cm) 24" (61.0 cm) 18" (45.7 cm) 24" (61.0 cm) Overall height (from bottom) 83-15/16" (213.2 cm) min to 84-3/4" (215.7 cm) max Overall depth from rear To front edge kickplate: 22-1/16”...
Page 8
Specifi cations (VRI/FRI/MVRI) Integrated All Refrigerator Description MVRI 30" 36" 30" 36" Overall width 30" (76.2 cm) 36" (91.4 cm) 30" (76.2 cm) 36" (91.4 cm) Overall height (from bottom) 83-15/16" (213.2 cm) min to 84-3/4" (215.7 cm) max Overall depth from rear To front edge kickplate: 22-1/16”...
Page 9
Specifi cations (VRI/FRI/MVRI) Integrated All Freezer Description MVFI 30" 36" 30" 36" Overall width 30" (76.2 cm) 30" (76.2 cm) 30" (76.2 cm) 36" (91.4 cm) Overall height (from bottom) 83-15/16" (213.2 cm) min to 84-3/4" (215.7 cm) max Overall depth from rear To front edge kickplate: 22-1/16”...
Anti-Tip Dimensions WARNING TIP OVER HAZARD Appliance is top heavy and tips easily when not completely installed. To avoid a hazard due to instability of the appliance, it must be installed according to the instructions including the anti-tip bracket Anti-tip Bracket The anti-tip bracket has holes set up on a grid in order to better locate a wall stud.
DO NOT particles in the water line. use an extension cord or ungrounded (two-prong) adapter. Viking Range, LLC is not responsible for property • damage due to improper installation or water If codes permit a separate grounding wire connection.
Use two or more people • The installation of Viking Range, LLC units with a reverse to move and install appliance. Failure to do so can result in death or...
Moving Unit Remove shipping brackets from skid by removing four Slip appliance dolly between unit and skid. bolts (two on each side) with a 1/2” (1.3 cm) deep-well Remove unit from skid. Note: Use excess packaging socket wrench and a pair of pliers. Note: Tilting unit is not to protect decorative trim;...
Optional Custom Front Panels - Dimensions Note: Overlay panel must be dry, solid, straight one-piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended. Maximum panel weight: 18" door panel - 28 lbs (12.6 kg) Custom Panel - hole locations 24"...
Optional Custom Front Panels - Install In order to access the mounting holes, unsnap panel trim on both sides of door. Panel trim Mounting Screw locations...
Water Line Installation WARNING TIP OVER HAZARD Appliance is top heavy and tips easily when not completely installed. To avoid a hazard due to instability of the appliance, it must be installed according to the instructions including the anti-tip bracket Ensure you have approximately 6 ft.
Page 19
Water Line Installation With the refrigerator in line with the cutout, but outside of the cabinetry, insert the copper tubing through the indicated hole. Push the copper tubing through the machine compartment until it comes out the front side of the refrigerator.
Leveling Unit Once the unit is in position, height adjustment can be made from the front. Remove access panel just below the water fi lter. Using a 5/16" hex drive, turn clockwise to raise the unit or counterclockwise to lower. Use the lowest torque setting when using a power drill. Do not turn the leveling legs by hand.
Flush Mount Side Trim After the unit has been placed in the cutout, leveled and all connections completed, the unit will need to be fastened to the cabinetry. Open the door. Using the fl at wood screws, fasten the unit to the cabinetry on both sides. NOTE: Only use the screws provided and use caution when installing the fastening screws to prevent scratching the frame.
Door Stop Adjustment Your refrigerator is factory set at a 90 degree opening. The 90 degree door stop opening is shown in the illustration below with the long end of the door stop facing away from the door. To change to 105 door stop, locate the door stop on top of the door hinge.
Water Filter System Specifi cation and Performance Data Sheet This system has been tested according to NSF/ANSI 42/53 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration of less than or equal to the permissible limit for water leaving the system, as specifi ed in NSF/ANSI 42/53.* (100% safety factors built-in for unmetered usage for health claims only.) NSF Specifi ed Chal- Average...
Performance Checklist —Verify cabinet size. —Align/square door(s). — Verify electrical supply and water supply (if applicable). — Verify drain pan is properly installed and there are no leaks on — Install anti-tip device(s) and verify unit is secure. water connection. —...
Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency, or if you continue to have service problems, contact Viking Range, LLC at 1-888-(845-4641), or write to: VIKING RANGE, LLC...
Page 28
Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-(845-4641) or visit our web site at vikingrange.com 062223-000A EN (050119)