Maintenance; Optional Accessories - Makita UH201DSAX Instruction Manual

CAUTION:
Overreaching with a hedge trim-
mer, particularly from a ladder, is extremely
dangerous. Do not work while standing on anything
wobbly or infirm.
NOTICE:
Do not attempt to cut branches thicker
than 10 mm in diameter with the tool. Cut branches
to 10 cm lower than the cutting height using branch
cutters before using the tool.
► Fig.45: (1) Cutting height (2) 10 cm
NOTICE:
Do not cut down dead trees or similar
hard objects. Doing so may damage the tool.
NOTICE:
Do not trim the grass or weeds while
using the shear blades. The blades may become
tangled in the grass or weeds.
Hold the tool with one hand, pull the switch trigger while
pressing the lock-off button, and then move it forward.
► Fig.46
For basic operation, tilt the blades toward the trimming
direction and move it calmly and slowly at the speed
rate of 3 to 4 seconds per meter.
► Fig.47
To tie a string at the desired height and to trim along it
help you to cut a hedge top evenly.
► Fig.48
If the chip receiver is attached to the blades, it gathers
discarded leaves and makes clean-up afterward much
easier.
To cut a hedge side evenly, cut from the bottom to top.
► Fig.49
When trimming to make a round shape (trimming box-
wood or rhododendron, etc.), trim from the root to the
top for a beautiful finish.
► Fig.50

MAINTENANCE

CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning the tool
Clean the tool by wiping off dust with a dry cloth or one
dipped in soapy water and wrung out.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Blade maintenance
Before the operation or once per hour during operation,
apply low-viscosity oil (machine oil, or spray-type lubri-
cating oil) to the blades.
► Fig.51
► Fig.52
After operation, remove dust from both sides of the
blades with a wired brush, wipe it off with a cloth and
then apply low-viscosity oil (machine oil, or spray-type
lubricating oil) to the blades.
► Fig.53
► Fig.54
NOTICE:
Do not wash the blades in water. Doing
so may cause rust or damage to the tool.
NOTICE:
Dirt and corrosion cause excessive
blade friction and shorten the operating time per
battery charge.
Storage
The hook hole in the tool bottom is convenient for hang-
ing the tool from a nail or screw on the wall.
Attach the blade cover to the shear blades so that the
blades are not exposed. Store the tool out of the reach
of children. Store the tool in a place not exposed to
moisture or rain.
► Fig.55: 1. Hole
► Fig.56: 1. Hole
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Shear blade assembly (for grass shear use)
• Shear blade cover (for grass shear use)
• Grass receiver (for grass shear use)
• Long handle attachment (for grass shear use)
• Shear blade assembly (for hedge trimmer use)
• Shear blade cover (for hedge trimmer use)
• Chip receiver (for hedge trimmer use)
• Storage case
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
19 ENGLISH