Page 1
Safety and Reference Please read this manual carefully before operating your TV and retain it for future reference. OLED77W8PSA OLED65W8PSA OLED77W8PDA OLED65W8PDA *MFL70370802* www.lg.com Copyright ⓒ 2018 LG Electronics Inc. All Rights Reserved. (1803-REV01)
Important Safety Instruction • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. •...
Page 3
Warning! Safety • Ventilation - Install your TV where there is proper ventilation. Do not install in Instructions a confined space such as a bookcase. - Do not install the product on a carpet or cushion. - Do not block or cover the product with cloth or other materials while unit is plugged in.
Page 4
• Grounding (Except for devices which are not grounded.) • Batteries - TV with a three-prong grounded AC plug must be connected to - Store the accessories (battery, etc.) in a safe location out of the a three-prong grounded AC outlet. Ensure that you connect the reach of children.
Optional Extras Preparing Optional extras can be changed or modified for quality improvement • When the TV is turned on for the first time after being shipped without any notification. Contact your dealer for buying these items. from the factory, initialization of the TV may take approximately These devices work only with certain models.
Lifting and moving the TV • Avoid touching the screen at all times, as this may result in damage to the screen. • Do not place the product on the floor with its front facing When moving or lifting the TV, read the following to prevent the TV down without padding.
Page 7
Provided item Wall mount Punching Guide Wall • When installing the wall mount, check the positions of the wooden studs using a stud finder. Then, fasten the screws on at least two Wall mounting screw separate studs before proceeding. Wall mounting anchor Ø5 x L65 Stud Wall mounting screw for wood...
Tools you will need • When mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables • Phillips head + driver (manual or motorized) / on the back of the TV. Ø...
Using the kensington security Other connections system (optional) Connect your TV to external devices. For the best picture and audio quality, connect the external device and the TV with the HDMI cable. (For OLED65W8*) The Kensington security system connector is located at the rear of HDMI the Companion Box (AV Box).
Using Button • In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to You can simply operate the TV functions, using the button. another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
Page 11
Using Magic Remote * To use the button, press and hold for more than 3 seconds. Control (POWER) Turns the TV on or off. You can turn your set-top box on or off by adding the set- top box to the universal remote control for your TV. (Depending upon model) Number buttons Enters numbers.
Troubleshooting Registering Magic Remote Control How to register the Magic Remote Control Cannot control the TV with the remote control. • Check if anything such as tape has been placed over the receiver. To use the Magic Remote, first pair it with your TV. •...
Page 13
Generated Sound • Cracking noise A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required. • Electrical circuit humming/panel buzzing A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product.
Specifications Product specifications may be changed without prior notice due to upgrade of product functions. (Depending upon country) Broadcasting Specifications OLED65W8PSA OLED65W8PDA Model OLED77W8PSA OLED77W8PDA Digital Analog Digital Analog Television system SBTVD (ISDBT) NTSC / PAL-M / PAL-N DVB-T/T2 NTSC / PAL-M / PAL-N...
Open Source Software Notice Information To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource. lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
Page 16
Important Information for Information on Functions Supporting Image Quality in Preventing Image Retention Relation to Temporary Image Retention OLED is a self-emissive technology, which brings many significant benefits to image quality and performance. As with any self-emitting • OLED TV offers a function called Pixel Refresher, which helps to display, it is possible for users of OLED TVs to experience temporary prevent temporary image retention.
Page 17
Regulatory WARNING! Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as: • Using cabinets or stands recommended by the manufacturer of the television set.
Page 18
The model and serial numbers of the TV are located on the back and on one side of the TV. Record them below should you ever need service. MODEL SERIAL NO.
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.com...
KEY CODES KEY CODES • This feature is not available for all models. Code Code Function Note Function Note (Hexa) (Hexa) CH +, PR + R/C Button List R/C Button CH -, PR - R/C Button Exit R/C Button Volume + R/C Button PIP(AD) R/C Button...
Page 21
EXTERNAL CONTROL DEVICE SETUP EXTERNAL CONTROL DEVICE SETUP • Image shown may differ from your TV. Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Note: The type of control port on the TV can be different between model series.
Page 22
EXTERNAL CONTROL DEVICE SETUP (TV) (PC) (TV) (PC) Phone jack Type RS-232C IN • You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and (CONTROL & SERVICE) (PC) (TV) the TV, which is specified in the manual. RS-232C IN (CONTROL &...
EXTERNAL CONTROL DEVICE SETUP Communication Parameters • Baud rate : 9600 bps (UART) • Stop bit : 1 bit • Data length : 8 bits • Communication code : ASCII code • Parity : None • Use a crossed (reverse) cable. Command reference list (Depending on model) DATA...
EXTERNAL CONTROL DEVICE SETUP Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99.
Page 25
EXTERNAL CONTROL DEVICE SETUP * Commands may work differently depending on model and signal. 01. Power (Command: k a) Ack [d][ ][Set ID][ ][OK/NG][Data][x] ► To control Power *On or Off of the set. * In case of video mute on only, TV will display On Transmission[k][a][ ][Set ID][ ][Data][Cr] Screen Display(OSD).
Page 26
EXTERNAL CONTROL DEVICE SETUP 08. Color/Colour (Command: k i) 13. Treble (Command: k r) ► To adjust the screen Color(Colour). ► To adjust treble. You can also adjust colour in the PICTURE menu. You can also adjust in the AUDIO menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64...
Page 27
EXTERNAL CONTROL DEVICE SETUP 18. Equalizer (Command : j v) * Analog Antenna/Cable ► Adjust EQ of the set. [Data 00][Data 01] Channel Data Transmission [j][v][ ][Set ID][ ][Data][Cr] Data 00 : High byte channel data Data 01 : Low byte channel data - 00 00 ~ 00 C7 (Decimal : 0 ~ 199) Data 02 : Input Source (Analog) - 00 : Antenna TV (ATV)
Page 28
EXTERNAL CONTROL DEVICE SETUP * Analog Antenna/Cable 2. Tune to the digital antenna (ATSC) channel 30-3. Set ID = All = 00 Data 00 : Physical Channel Number Data 00 = Don’t know Physical = 00 - Antenna (ATV) : 02~45 (Decimal: 2 ~ 69) Data 01 &...
Page 29
11 11 EXTERNAL CONTROL DEVICE SETUP 2. Tune to the BS (ISDB-BS) channel 30. 24. Input select (Command: x b) Set ID = All = 00 (Main Picture Input) Data 00 = Don’t know Physical = 00 ► To select input source for main picture. Data 01 &...
Page 30
EXTERNAL CONTROL DEVICE SETUP * [Data 02], [Data 03] functions depend on model 3) When [Data 00] is 06, 07 and signal. 00 : Off 01 : On * If [Data 00] is 00 (3D On), [Data 03] has no meaning.
SMART TV Quick Setup Guide * Image shown may differ from your TV. * Image shown on a PC or mobile phone may vary depending on the OS(Operating System). * App icon positions may vary on the platform, depending on the software version. Network Settings 1 Press the (Home) button on the remote to...
Troubleshooting Network Problems (Home) button on the remote to 1 Press the Check the AP (Router) or consult your Internet (Settings) access the Home menu. Point the service provider. Wheel (OK) icon and select by pressing the button on the remote. When X appears next to Gateway: Unplug the power cord of the AP (Router) and try to connect after 5 seconds.
SmartShare PC SW Installing & Setting 1 Install the SmartShare PC SW programme on your PC. 2 Go to www.lg.com. Then, select your region. 3 Select SUPPORT. Then, select Drivers & Software, SOFTWARE UPDATE or Software & Firmware. 4 Search for your model. Then, select SmartShare PC SW. 5 You can run the programme when installation is complete.
Page 35
Wi-Fi Direct Setting (Home) → (Settings) → ) (All Settings) → Network → Wi-Fi Direct WI-FI Direct If a local network is not available, you can connect a portable device directly to the Picture Network / REFRESH LIST TV using Wi-Fi Direct. ꔐ...
Page 36
Seguridad y Consultas Lea atentamente este manual antes de poner en marcha el equipo y consérvelo para futuras consultas. OLED77W8PSA OLED65W8PSA OLED77W8PDA OLED65W8PDA www.lg.com Copyright ⓒ 2018 LG Electronics Inc. Todos los derechos reservados.
Instrucciones de Seguridad Importantes • Lea estas instrucciones. • Conserve estas instrucciones. • Preste atención a las advertencias. • Siga todas las instrucciones. • No use el aparato cerca del agua. • Limpie únicamente con un paño seco. • No tape ni bloquee las aberturas de ventilación. Realice la instalación siguiendo las instrucciones del fabricante. •...
Page 38
¡Advertencia! Instrucciones • Ventilación - Instale el televisor en un lugar con ventilación adecuada. No de seguridad lo coloque en un lugar cerrado como, por ejemplo, un estante para libros. - No instale el producto en alfombras o cojines. - No bloquee o cubra el producto con paño u otros materiales mientras esté...
Page 39
• Puesta a tierra (Excepto dispositivos sin conexión a tierra.) • Baterías - El televisor con un conector de ca de conexión a tierra de tres - Guarde los accesorios (baterías, etc.) en un lugar seguro lejos del clavijas debe conectarse a un tomacorriente de ca de conexión a alcance de los niños.
Complementos opcionales Preparación Los complementos opcionales se pueden cambiar o modificar para • Cuando se enciende la TV por primera vez después de ser mejorar la calidad, sin necesidad de aviso previo. Para adquirir estos enviada desde la fábrica, la inicialización de la TV puede tardar elementos, comuníquese con su distribuidor.
Levantamiento y traslado • No toque la pantalla. De lo contrario, podría dañarla. • No coloque el producto en el piso con la parte frontal de su TV hacia abajo sin una almohadilla. Al hacerlo puede causar daños a la pantalla. •...
Page 42
Elemento proporcionado Montaje de pared Guía de perforación Pared • Cuando instale el soporte de pared, compruebe las posiciones de las vigas de madera con un detector de vigas. Luego, asegure los Tornillo para soporte de pared tornillos en al menos dos vigas antes de continuar. Anclaje para soporte de pared Ø5 x L65 Viga...
Herramientas que necesitará • Cuando monte la televisión en la pared, no la instale colgándola por los cables de señal y alimentación que • Destornillador Phillips (manual o motorizado) / se encuentran en su parte posterior. Broca de 8 mm de diámetro / Nivel / Detector de clavos / Taladro •...
Usar el sistema de seguridad Otras conexiones Kensington (opcional) Conecte su TV a dispositivos externos. Para tener una mejor calidad de imagen y audio, conecte el dispositivo externo y el televisor con el cable (Para OLED65W8*) HDMI tal como se muestra. El conector del sistema de seguridad Kensington se encuentra en la parte posterior del decodificador complementario (caja AV).
Uso del botón • En el modo PC, es posible que haya ruido asociado con la resolución, los patrones verticales, el contraste o el brillo. Si se producen ruidos, cambie la resolución de la salida de la PC, cambie Puede operar la televisión con el botón. la frecuencia de actualización o ajuste el brillo y el contraste en el menú...
Page 46
Uso del Control Remoto * Para utilizar el botón, mantenga presionado durante más de tres segundos. Mágico (ENCENDIDO) Enciende o apaga el televisor. Para encender o apagar su decodificador, agregue el (Según el modelo) decodificador al control remoto universal de la televisión. Las descripciones en este manual se basan en los botones en el control Botones Numerales Permiten introducir números.
Solución de problemas Registro del Control Remoto Mágico Cómo registrar el Control Remoto Mágico No se puede controlar el televisor con el control remoto. • Compruebe si puso cualquier cosa sobre el receptor, como por Para utilizar el Control Remoto Mágico, primero emparéjelo con su TV. ejemplo cinta adhesiva.
Page 48
Reproducción de ruidos • Crujidos es posible que se produzcan crujidos cuando esté mirando televisión o al apagar el televisor; se trata de un ruido generado por la contracción térmica del plástico debido a la temperatura y la humedad. Este ruido es común en productos donde se requiere la deformación térmica.
Especificaciones Las especificaciones del producto pueden cambiar sin previo aviso debido a las actualizaciones de las funciones de los productos. (Según del país) Especificaciones de transmisión Modelo OLED65W8PSA, OLED77W8PSA OLED65W8PDA, OLED77W8PDA Digital Analógica Digital Analógica Sistema de televisión SBTVD (ISDBT)
Software de código abierto Para obtener el código fuente bajo GPL, LGPL, MPL y otras licencias de código abierto que contiene este producto, visite http://opensource. lge.com. Además del código fuente, se pueden descargar los términos de la licencia, las anulaciones de la garantía y los avisos de derechos de autor. LG Electronics también le proporcionará...
Page 51
Información importante Información sobre las funciones que ofrecen calidad de imagen en para evitar la retención de relación con la retención temporal imágenes de imagen • El televisor OLED ofrece una función denominada Optimizar OLED es una tecnología de emisiones automáticas, que ofrece muchas Píxeles, que ayuda a evitar la retención temporal de la imagen.
Page 52
Regulación ¡ADVERTENCIA! Nunca coloque una televisión en un lugar inestable. Se puede caer y provocar lesiones graves o la muerte. Puede evitar muchas lesiones, especialmente en niños, con tan solo tomar simples precauciones, como: • Usar los gabinetes o soportes recomendados por el fabricante de la televisión.
Page 53
Los números de modelo y de serie de la televisión se encuentran ubicados en su parte posterior y en uno de sus lados. Regístrelos en el siguiente espacio por si alguna vez necesita recurrir al servicio técnico. MODELO N.º DE SERIE...
MANUAL DEL USUARIO CONFIGURACIÓN DE DISPOSITIVOS DE CONTROL EXTERNOS Lea atentamente este manual antes de poner en funcionamiento el equipo y consérvelo para futuras consultas. www.lg.com...
Page 55
CÓDIGOS DE TECLA CÓDIGOS De teCla • Esta función no está disponible en todos los modelos. Código Código Función Nota Función Nota (Hexa) (Hexa) CH +, PR + Botón RC Lista Botón RC CH -, PR - Botón RC Salir Botón RC Volumen + Botón RC...
Page 56
CONFIGURACIÓN DE DISPOSITIVOS DE CONTROL EXTERNOS CONFIGURaCIÓN De DISPOSItIVOS De CONtROl eXteRNOS • Es posible que la imagen que se muestra no sea exactamente igual a la de su TV. Conecte el USB al convertidor de serie/conector de entrada RS-232C, a un dispositivo de control externo (como una computadora o un sistema de control A/V) para controlar externamente las funciones del producto.
Page 57
CONFIGURACIÓN DE DISPOSITIVOS DE CONTROL EXTERNOS (TV) (PC) (TV) (PC) Tipo de adaptador telefónico RS-232C IN RS-232C IN • Para realizar la conexión entre la PC y la TV, que se especifica en el manual, debe comprar el cable de (CONTROL &...
CONFIGURACIÓN DE DISPOSITIVOS DE CONTROL EXTERNOS Parámetros de comunicación • Velocidad en baudios : 9600 bps (UART) • Bit de parada: 1 bit • Longitud de datos: 8 bits • Código de comunicación: código ASCII • Paridad: Ninguna • Use un cable cruzado (reversa). lista de referencia de comandos (según el modelo) Datos...
Page 59
CONFIGURACIÓN DE DISPOSITIVOS DE CONTROL EXTERNOS Protocolo de transmisión/Recepción transmisión [Comando1][Comando2][ ][ID del televisor][ ][Dato][Cr] [Comando 1] : Primer comando para controlar la TV. (j, k, m o x) [Comando 2] : Segundo comando para controlar la TV. [ID del televisor] : Puede ajustar [ID del televisor] para elegir el número de ID del monitor que desea en el menú...
Page 60
CONFIGURACIÓN DE DISPOSITIVOS DE CONTROL EXTERNOS * Según el modelo y la señal, los comandos podrán funcionar de un modo diferente. 01. Potencia (Comando: k a) 03. Screen Mute (Silencio de pantalla) (Comando: k d) ► Para controlar el encendido o apagado del dispositivo.
Page 61
CONFIGURACIÓN DE DISPOSITIVOS DE CONTROL EXTERNOS 07. Brillo (Comando: k h) 12. Remote control lock mode (Modo de bloqueo del control remoto) (Comando: k m) ► Para ajustar el brillo de la pantalla. También puede ajustar el brillo en el menú ►...
Page 62
CONFIGURACIÓN DE DISPOSITIVOS DE CONTROL EXTERNOS 16. Color Temperature (Temperatura de color) Datos (Comando: x u) 00: apagado 01: mínimo ► Para ajustar la temperatura de color. También 02: medio puede ajustar Color Temperature (Temperatura 03: máximo de color) en el menú IMAGEN. 04: Automático (para TV LCD/TV LED)/ Transmisión [x][u][ ][ID del televisor][ ][Dato] Intelligent sensor (Sensor inteligente) (para...
Page 63
CONFIGURACIÓN DE DISPOSITIVOS DE CONTROL EXTERNOS ID del televisor = Todo = 00 - 0b : Cable DTV Plus – usar número de canal físico Datos 00 & 01 = Datos de canal es 1000 = 03 E8 Datos 02 = Satélite de TV digital = 40 - 2b : Cable DTV Plus –...
Page 64
11 11 CONFIGURACIÓN DE DISPOSITIVOS DE CONTROL EXTERNOS - 09: CS2 (satélite de comunicación 2) • Para TV plasma ► Para controlar la luz del panel * Ejemplos de comandos de sintonización: 1 Sintonizar el canal Antena digital (ISDB-T) 17-1. Transmisión [m][g][ ][ID del televisor][ ][Dato] ID del televisor = Todo = 00 [Cr]...
Page 65
CONFIGURACIÓN DE DISPOSITIVOS DE CONTROL EXTERNOS * Si [Dato 00] es 01 (3D apagado) o 02 (3D a * Si la condición de la conversión no se cumple, el 2D), [Dato 01], [Dato 02] y [Dato 03] no son comando se trata como NG. relevantes.
Guía de configuración rápida del SMART TV * La imagen que se muestra puede ser diferente a su televisor. * La imagen que se muestra en una PC o un teléfono móvil puede variar según el sistema operativo (sistema operativo). * Las posiciones de los íconos de la aplicación pueden variar en la plataforma según la versión del software.
Page 67
Resolución de problemas de red (Inicio) del control remoto 1 Presione el botón Siga las instrucciones que están a continuación y que se relacionan con el estado de red. para acceder al menú Inicio. Vaya al ícono (Configuración) y selecciónelo con el botón Revise el televisor o el AP (enrutador).
Page 68
Instalación y configuración de SmartShare PC SW 1 Instale el programa SmartShare PC SW en su PC. 2 Vaya a . Luego, seleccione su región. 3 Seleccione Soporte. 4 Select Software y actualizaciones. Then, select SmartShare. 5 Descargue el Software SmartShare PC e instálelo en su PC. Puede ejecutar el programa al finalizar la instalación.
Page 69
Configuración de Wi-Fi Direct (Inicio) → (Configuración) → ) (Todos los ajustes) → Red → Wi-Fi WI-FI Direct Direct Imagen Red / ACTUALIZAR LISTA Si no hay una red local disponible, puede conectar un dispositivo portátil Audio ꔐ directamente al televisor con Wi-Fi Direct. Canales , puede compartir archivos o pantallas de dispositivos conectados a Wi-Fi Direct.
Page 70
Please read this manual carefully before operating your set and retain it for future reference. ESPAÑOL Guía Rápida de Configuración OLED77W8PSA OLED65W8PSA Lea atentamente este manual antes de poner en marcha el equipo y consérvelo para futuras consultas. OLED77W8PDA OLED65W8PDA...
Page 71
ENGLISH Read Safety and Reference. ESPAÑOL Leer Seguridad y Consultas.