Page 1
Safety and Reference Please read this manual carefully before operating your set and retain it for future reference. OLED65G7P OLED77G7P *MFL69707622* www.lg.com P/NO : MFL69707622 (1701-REV00)
Page 2
Warning! Important Safety • Only use attachments/accessories specified by the manufacturer. instructions • Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution Read these instructions. Keep these instructions. when moving the cart/apparatus combination to Heed all warnings.
Page 3
mechanical abuse, such as being twisted, kinked, charges. Section 810 of the National Electrical pinched, closed in a door, or walked upon. Pay Code (NEC) in the U.S.A. provides information particular attention to plugs, wall outlets, and with respect to proper grounding of the mast the point where the cord exits the device.
Page 4
• Handle the adapter carefully to avoid dropping • New features may be added to this TV in the or striking it. An impact could damage the future. adapter. • The items supplied with your product may vary • Keep the product away from direct sunlight. depending upon the model.
Lifting and Moving the TV • Avoid touching the screen at all times, as this may result in damage to the screen. • Do not place the product on the floor with its front facing down without padding. When moving or lifting the TV, read the following Failure to do so may result in damage to the to prevent the TV from being scratched or screen.
Adjusting the Menu 1 Insert and tighten the eye-bolts or TV brackets and bolts on the back of the TV. When the TV is turned on, press the button one - If there are bolts inserted at the eye-bolts time. You can adjust the Menu items using the position, remove the bolts first.
• If you record a TV program on a DVD recorder or wall mount. VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR. (For OLED65G7P) For more information about recording, refer to the manual provided with the connected device. Provided Item •...
Other Connections • In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh Connect your TV to external devices. For the best rate to another rate or adjust the brightness and picture and audio quality, connect the external contrast on the Picture menu until the picture is...
Battery Installation • DO NOT INGEST BATTERY. CHEMICAL BURN HAZARD. • The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, incinerate, or heat above 100 °C (212 °F). Replace the battery part no.
Page 10
Adjusts the volume level. (Mute) Mutes all sounds. (Voice recognition) Press the button and speak when the voice display window appears on the TV screen. • Network connection is required to use the voice recognition function. * (Search) Shows the search mode. Scrolls through the saved channels.
Open Source Software Notice * You can zoom in on the area where the remote control is pointed. Information These access special functions in some menus. * To use the button, press and hold for more than To obtain the source code under GPL, LGPL, MPL, 3 seconds.
Television System • Abnormal Display - If the TV feels cold to the touch, there may be a ATSC, NTSC-M, 64 & 256 QAM small flicker when it is turned on. This is normal; there is nothing wrong with TV. Some minute Program Coverage dot defects may be visible on the screen, appearing as tiny red, green, or blue spots.
Regulatory FCC RF Radiation Exposure Statement [For having wireless function (WLAN, Bluetooth,...)] This equipment complies with FCC radiation FCC NOTICE exposure limits set forth for an uncontrolled environment. This transmitter must not be (For USA) colocated or operating in conjunction with any other antenna or transmitter.
WARNING! (For Canada) [For product having the wireless function using 5 GHz frequency bands] Never place a television set in an unstable location. A television set may fall, causing serious • The device for operation in the band 5150–5250 personal injury or death. Many injuries, particularly MHz is only for indoor use to reduce the to children, can be avoided by taking simple potential for harmful interference to co-channel...
CHILD SAFETY: PROPER TELEVISION PLACEMENT MATTERS THE CONSUMER ELECTRONICS INDUSTRY CARES • Manufacturers, retailers and the rest of the consumer electronics industry are committed to making home entertainment safe and enjoyable. • As you enjoy your television, please note that all televisions – new and old- must be supported on proper stands or installed according to the manufacturer’s recommendations.
Page 16
LG Customer Information Center Declaration of Conformity For inquires or comments, visit www.lg.com or call; Trade Name Model OLED65G7P-U, 1-800-984-6306 OLED77G7P-U 1-888-542-2623 CANADA Responsible Party LG Electronics Inc. Register your product Online! Address 1000 Sylvan Ave. Englewood www.lg.com Cliffs NJ 07632 U.S.A...
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.com...
KEY CODES KEY CODES • This feature is not available for all models. Code Code Function Note Function Note (Hexa) (Hexa) CH +, PR + R/C Button List R/C Button CH -, PR - R/C Button Exit R/C Button Volume + R/C Button PIP(AD) R/C Button...
Page 19
EXTERNAL CONTROL DEVICE SETUP EXTERNAL CONTROL DEVICE SETUP • Image shown may differ from your TV. Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Note: The type of control port on the TV can be different between model series.
Page 20
EXTERNAL CONTROL DEVICE SETUP (TV) (PC) (TV) (PC) Phone jack Type RS-232C IN • You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and (CONTROL & SERVICE) (PC) (TV) the TV, which is specified in the manual. RS-232C IN (CONTROL &...
EXTERNAL CONTROL DEVICE SETUP Communication Parameters • Baud rate : 9600 bps (UART) • Stop bit : 1 bit • Data length : 8 bits • Communication code : ASCII code • Parity : None • Use a crossed (reverse) cable. Command reference list (Depending on model) DATA...
EXTERNAL CONTROL DEVICE SETUP Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99.
Page 23
EXTERNAL CONTROL DEVICE SETUP * Commands may work differently depending on model and signal. 01. Power (Command: k a) Ack [d][ ][Set ID][ ][OK/NG][Data][x] ► To control Power *On or Off of the set. * In case of video mute on only, TV will display On Transmission[k][a][ ][Set ID][ ][Data][Cr] Screen Display(OSD).
Page 24
EXTERNAL CONTROL DEVICE SETUP 08. Color/Colour (Command: k i) 13. Treble (Command: k r) ► To adjust the screen Color(Colour). ► To adjust treble. You can also adjust colour in the PICTURE menu. You can also adjust in the AUDIO menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64...
Page 25
EXTERNAL CONTROL DEVICE SETUP 18. Equalizer (Command : j v) * Analog Antenna/Cable ► Adjust EQ of the set. [Data 00][Data 01] Channel Data Transmission [j][v][ ][Set ID][ ][Data][Cr] Data 00 : High byte channel data Data 01 : Low byte channel data - 00 00 ~ 00 C7 (Decimal : 0 ~ 199) Data 02 : Input Source (Analog) - 00 : Antenna TV (ATV)
Page 26
EXTERNAL CONTROL DEVICE SETUP * Analog Antenna/Cable 2. Tune to the digital antenna (ATSC) channel 30-3. Set ID = All = 00 Data 00 : Physical Channel Number Data 00 = Don’t know Physical = 00 - Antenna (ATV) : 02~45 (Decimal: 2 ~ 69) Data 01 &...
Page 27
11 11 EXTERNAL CONTROL DEVICE SETUP 2. Tune to the BS (ISDB-BS) channel 30. 24. Input select (Command: x b) Set ID = All = 00 (Main Picture Input) Data 00 = Don’t know Physical = 00 ► To select input source for main picture. Data 01 &...
Page 28
EXTERNAL CONTROL DEVICE SETUP * [Data 02], [Data 03] functions depend on model 3) When [Data 00] is 06, 07 and signal. 00 : Off 01 : On * If [Data 00] is 00 (3D On), [Data 03] has no meaning.
Page 30
OLED TV ENGLISH Easy Setup Guide Please read this manual carefully before operating your set and retain it for future reference. OLED65G7P ESPAÑOL Guía Rápida de Configuración OLED77G7P Lea atentamente este manual antes de poner en marcha el equipo y consérvelo para futuras consultas.
Page 31
ENGLISH Read Safety & Reference. ESPAÑOL Leer Seguridad y Consultas. FRANÇAIS Lisez Sécurité et références.
Page 34
www.lg.com/us/support ENGLISH Easy TV Connect Guide (Animation) ESPAÑOL Guía Rápida de Conexión de TV (Sólo en Inglés) FRANÇAIS Guide simplifié pour la connexion du téléviseur (Offert en anglais seulement)
Page 37
: mm (inches / pulgadas / po) : kg (lbs / libras / lb) 1,461 1 461 31.7 31,7 OLED65G7P-U 5.0 A / 500 W 5,0 A / 500 W (57.5) (57,5) (34.7) (34,7) (9.5) (9,5) (35.1) (35,1) (2.6) (2,6) (69.8)