1. Manuals
  2. Brands
  3. Powermatic Manuals
  4. Dust Collector
  5. PM1900TX-BK3
  6. Instructions and parts manual

Powermatic PM1900TX-BK3 Instructions And Parts Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
This .pdf document is bookmarked
Instructions and Parts Manual
PM1900TX Dust Collector
Now with
PM1900TX with Filter Bag Kit (1792071K)
PM1900TX with Canister Kit (1792072K)
WALTER MEIER (Manufacturing), Inc.
427 New Sanford Road
LaVergne, TN 37086
Part No. M-1792071
Ph.: 800-274-6848
Revision A3 07/2013
www.powermatic.com
Copyright © 2013 Walter Meier (Manufacturing), Inc.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PM1900TX-BK3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Powermatic PM1900TX-BK3

Summary of Contents for Powermatic PM1900TX-BK3

  • Page 1 Now with PM1900TX with Filter Bag Kit (1792071K) PM1900TX with Canister Kit (1792072K) WALTER MEIER (Manufacturing), Inc. 427 New Sanford Road LaVergne, TN 37086 Part No. M-1792071 Ph.: 800-274-6848 Revision A3 07/2013 www.powermatic.com Copyright © 2013 Walter Meier (Manufacturing), Inc.

  • Page 2: Warranty And Service

    This warranty covers only the initial purchaser of the product. WHAT IS THE PERIOD OF COVERAGE? The general POWERMATIC warranty lasts for the time period specified in the product literature of each product. WHAT IS NOT COVERED? The Five Year Warranty does not cover products used for commercial, industrial or educational purposes. Products with a Five Year Warranty that are used for commercial, industrial or education purposes revert to a One Year Warranty.

  • Page 3: Table Of Contents

    Table of Contents   Warranty and Service ..........................2   Table of Contents ............................ 3   Warning ..............................4   Introduction ............................. 6   Specifications ............................6   Unpacking ............................... 7   Contents of Shipping Carton ........................ 7   Base Machine Assembly.......................... 8  ...

  • Page 4: Warning

    Warning 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3.
  • Page 5 20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. To reduce the risk of electric shock, do not use outdoors or on wet surfaces. 23.

  • Page 6: Introduction

    Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for a Powermatic Model PM1900TX Dust Collector. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual.

  • Page 7: Unpacking

    Unpacking Remove all contents from the shipping carton and check against the Contents of Shipping Carton below to verify that all items have been received. Report any damage to your distributor. Do not discard any shipping material until after the dust collector has been assembled and is running properly.

  • Page 8: Base Machine Assembly

    3. Insert an M8x20 hex cap screw (A), through the Base Machine Assembly M8 washer (D) and flanges of the connector tube (R) and impeller housing (N). The dust collector must not be connected to the power source 4. Place another washer (D) and a hex nut (F) on during assembly.

  • Page 9: Handles

    Handles Cone Installation Install the cone assembly as shown in Figure 3a. 1. Remove the plate (Y) from the handle (X) by loosening the two socket head cap screws (Z) 1. Mount the cone support bracket (AA) to the with a 6mm hex wrench. housing with four M6x12 hex cap screws (FF) 2.

  • Page 10: Filter Bag System Assembly

    9. Thread the retainer strap (Figure 6) through Filter Bag System Assembly the loops on the filter bag, and fasten it to the collector housing, as shown in Figure 7. Note: If your dust collection system includes the canister kit, proceed to Canister System Assembly on page 11.

  • Page 11: Canister System Assembly

    6. Insert and tighten the four knobs into the Figure 10 threaded holes on the canister (Figure 10). Note: The Powermatic® label on the front of the canister should have a negligible effect upon air flow. However, if zero effect is desired, the label...

  • Page 12: Electrical Connections

    Check with a qualified electrician or service Electrical Connections personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Electrical connections must be made by a qualified electrician in Repair or replace a damaged or worn cord compliance with all relevant codes.

  • Page 13: Setting The Timer (1-Phase Models)

    Properly Contact your nearest Powermatic distributor for discard the plastic bag. a full line of Dust Collector hoses and accessories.

  • Page 14: Replacement Parts

    Replacement Parts Replacement Parts are listed on the following pages. To order parts or reach our service department, call 1-800-274- 6848, Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Breakdown for PM1900TX Dust Collector (Base Machine)

  • Page 15: Parts List For Pm1900Tx Dust Collector (Base Machine)

    20 ..... PM1900-120 ....Left Housing ..................1 21 ..... PM1900-121 ....Right Housing ..................1 22 ..... PM1900-122 ....Support Bar ................... 2 23 ..... PWBS14-254SN ..POWERMATIC Nameplate, Small ............1 24 ..... TS-2361061 .....Lock Washer ............M6 ......2 25 ..... TS-1550041 .....Flat Washer ............M6 ......2 26 .....
  • Page 16 Index No. Part No. Description Size 37 ..... TS-1490031 .....Hex Cap Screw ..........M8x20 ...... 36 38 ..... TS-1490041 .....Hex Cap Screw ..........M8x25 ......4 39 ..... PM1900-139 ....Magnetic Switch ..........for 3HP, 230V, 1Ph ..1 39-1 ..PM1900-139-1 ..Power Cord ............14AWG x 3C ....1 39-2 ..

  • Page 17: Parts List And Breakdown For Pm1900Tx Filter Bag System

    Parts List and Breakdown for PM1900TX Filter Bag System Index No. Part No. Description Size ....1791075B ....Collection and Filter Bag System (includes #1 thru 6) ......1 1 ....1791075F ....Filter Bag ............30 micron ....2 2 ....430005 ....Retainer Strap ..................2 3 ....

  • Page 18: Breakdown For Pm1900Tx Canister Filter System

    Breakdown for PM1900TX Canister Filter System...

  • Page 19: Parts List For Pm1900Tx Canister Filter System

    23 ..... 331015 ....Plate ...................... 2 24 ..... TS-1482021 .....Hex Cap Screw ..........M6x12 ......4 ....PM1300-PLO ...Powermatic Label (not shown) ......5-1/2x14 Oval ..... 1 ....PM1900-CHP ...Canister Hardware Package (not shown) * ..........1 * Canister Hardware Package includes index # 2, 8, 9 and 12.

  • Page 20: Electrical Connections

    Electrical Connections Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. POWER SUPPLY CORD BLACK WHITE 2 3 0 V 1 1 5 V MOTOR CORD M O T O R...

This manual is also suitable for:

Pm1900txPm1900tx-ck1

Table of Contents