Table of Contents
Advertisement
Quick Links
This .pdf document is bookmarked
Instructions and Parts Manual
PM1300TX Dust Collector
Now with
PM1300TX with Filter Bag Kit (1791078K)
PM1300TX with Canister Kit (1791079K)
Powermatic
427 New Sanford Road
LaVergne, Tennessee 37086
Part No. M-1791078
Ph.: 800-274-6848
Revision B 05/2016
www.powermatic.com
Copyright © 2014 Powermatic
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Powermatic PM1300TX-BK
Summary of Contents for Powermatic PM1300TX-BK
- Page 1 Instructions and Parts Manual PM1300TX Dust Collector Now with PM1300TX with Filter Bag Kit (1791078K) PM1300TX with Canister Kit (1791079K) Powermatic 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-1791078 Ph.: 800-274-6848 Revision B 05/2016 www.powermatic.com Copyright © 2014 Powermatic...
-
Page 2: Warranty And Service
Warranty and Service Powermatic warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official Powermatic branded website. -
Page 3: Table Of Contents
Table of Contents Warranty and Service ..........................2 Table of Contents ............................ 3 Warning ..............................4 Introduction ............................. 6 Specifications ............................6 Unpacking ............................... 7 Contents of Shipping Carton ........................ 7 Base Machine Assembly.......................... 8 ... -
Page 4: Warning
5. Do not use this dust collector for other than its intended use. If used for other purposes, Powermatic disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use. - Page 5 20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. To reduce the risk of electric shock, do not use outdoors or on wet surfaces. 23.
-
Page 6: Introduction
Introduction This manual is provided by Powermatic covering the safe operation and maintenance procedures for a Powermatic Model PM1300TX Dust Collector. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. -
Page 7: Unpacking
Unpacking Remove all contents from the shipping carton and check against the Contents of Shipping Carton below to verify that all items have been received. Report any damage to your distributor. Do not discard any shipping material until after the dust collector has been assembled and is running properly. -
Page 8: Base Machine Assembly
Note: Refer to Figure 3 to make sure that the Base Machine Assembly connector tube is facing the proper direction. 3. Insert an M8x20 hex cap screw (A), through the The dust collector must not be M8 washer (C) and flanges of the connector connected to the power source tube (O) and fan housing (K). -
Page 9: Handles
Handles 1. Mount the cone support bracket (AA) to the housing with four M6x12 hex cap screws (FF) 1. Remove the plate (V) from the handle (U) by and tighten from beneath with four M6 hex loosening the two socket head cap screws nuts (GG). -
Page 10: Filter Bag System Assembly
Filter Bag System Assembly Note: If your dust collection system includes the canister kit, proceed to Canister System Assembly on page 11. 1. Insert a hanger bracket between support bar and collector housing (Figure 4). 2. Align holes and secure with two M8x20 hex cap screws and two M8 flat washers outside the housing, and two M8 flat washers and two M8 hex nuts inside the housing. -
Page 11: Canister System Assembly
14. Insert and tighten the four knobs into the Figure 10 threaded holes on the canister (Figure 10). Note: The Powermatic® label on the front of the canister should have a negligible effect upon air flow. However, if zero effect is desired, the label... -
Page 12: Electrical Connections
Check with a qualified electrician or service Electrical Connections personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Electrical connections must be made by a qualified electrician in Repair or replace a damaged or worn cord compliance with all relevant codes. -
Page 13: Operating The Machine
To operate the machine, use the buttons on the Contact your nearest Powermatic distributor for a full line of Dust Collector hoses and control panel, or use the provided remote accessories. -
Page 14: Cleaning The Canister Filter
Cleaning the Canister Filter Motor Clean the canister filter frequently to keep the Make frequent inspections of the motor fan and collector's performance at its optimum. To clean blow out (with low pressure air hose) or vacuum the filter, turn the handle a couple of rotations so any accumulation of foreign material in order to the dust falls into the clear plastic bag. -
Page 15: Replacement Parts
Replacement Parts are listed on the following pages. To order parts or reach our service department, call 1-800-274- 6848, Monday through Friday (see our website for business hours, www.powermatic.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. -
Page 16: Parts List For Pm1300Tx Dust Collector (Base Machine)
22 ..........Battery (local purchase) ........AAA ......2 23 ..... 430035 ....Rubber Gasket ..................1 24 ..... 430036 ....Rubber Gasket ..................1 25 ..... PWBS14-254SN ..POWERMATIC Nameplate, Small ............1 26 ..... 31A-208-2 ....Strain Relief ............PGA13.5 ....2 27 ..... PM1900-127 ....Handle....................2 28 ..... - Page 17 ....PM2700-440 ....Wide Stripe (not shown) ..............per ft....PM2700-441 ....Narrow Stripe (not shown) .............. per ft....PM1300-162 ....Powermatic Turbocone Decal (not shown) ..2-3/4”x8” ..... 1 ....PM1300-BMHP ..Base Machine Hardware Package (not shown) * ........1 ....DC1100-HP2 ...Hardware Package for Cone Assembly (index # 57 thru 61) ....1...
-
Page 18: Breakdown For Pm1300Tx Canister Filter System
Breakdown for PM1300TX Canister Filter System... -
Page 19: Parts List For Pm1300Tx Canister Filter System
23 ..... 331015 ....Plate ...................... 2 24 ..... TS-1482021 .....Hex Cap Screw ..........M6x12 ......4 ....PM1300-PLO ...Powermatic Label (not shown) ......5-1/2x14 Oval ..... 1 ....PM1900-CHP ...Canister Hardware Package (not shown) * ..........1 *Canister Hardware Package includes index # 2, 8, 9 and 12. -
Page 20: Parts List For Pm1300Tx Filter Bag System
Parts List for PM1300TX Filter Bag System Index No. Part No. Description Size ....1791077B ....PM1300 Collection and Filter Bag (includes #1 thru 5) ......1 1 ....1791077F ....Filter Bag ............30 micron ....1 2 ....410012 ....Retainer Strap ..................1 3 .... -
Page 21: Electrical Connections
Electrical Connections... - Page 22 This page intentionally left blank...
- Page 23 This page intentionally left blank...
- Page 24 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.powermatic.com...
Need help?
Do you have a question about the PM1300TX-BK and is the answer not in the manual?
Questions and answers