Powermatic PM1300TX Instructions And Parts Manual
  1. Manuals
  2. Brands
  3. Powermatic Manuals
  4. Dust Collector
  5. PM1300TX
  6. Instructions and parts manual

Powermatic PM1300TX Instructions And Parts Manual

Hide thumbs Also See for PM1300TX:
Table of Contents

Advertisement

Quick Links

Download this manual
This .pdf document is bookmarked
Instructions and Parts Manual
PM1300TX Dust Collector
Now with
PM1300TX with Filter Bag Kit (1791078K)
PM1300TX with Canister Kit (1791079K)
Powermatic
427 New Sanford Road
LaVergne, Tennessee 37086
Part No. M-1791078
Ph.: 800-274-6848
Revision B1 09/2018
www.powermatic.com
Copyright © 2014 Powermatic

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PM1300TX and is the answer not in the manual?

Questions and answers

Related Manuals for Powermatic PM1300TX

Summary of Contents for Powermatic PM1300TX

  • Page 1 This .pdf document is bookmarked Instructions and Parts Manual PM1300TX Dust Collector Now with PM1300TX with Filter Bag Kit (1791078K) PM1300TX with Canister Kit (1791079K) Powermatic 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-1791078 Ph.: 800-274-6848 Revision B1 09/2018 www.powermatic.com...

  • Page 2: Important Safety Instructions

    Keep children away. its intended use. If used for other purposes, 19. Make your workshop child proof with Powermatic disclaims any real or implied padlocks, master switches or by removing warranty and holds itself harmless from any starter keys.
  • Page 3 26. Do not use this dust collector with a 35. Do not leave the machine when it is plugged damaged cord or plug. in. Unplug from outlet when not in use and before servicing. 27. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

  • Page 4: Table Of Contents

    Replacement Parts ............................14 Breakdown for PM1300TX Dust Collector (Base Machine) ..............14 Parts List for PM1300TX Dust Collector (Base Machine) ............... 15 Breakdown for PM1300TX Canister Filter System .................. 17 Parts List for PM1300TX Canister Filter System ..................18 Parts List for PM1300TX Filter Bag System ....................

  • Page 5: Introduction

    Introduction This manual is provided by Powermatic covering the safe operation and maintenance procedures for a Powermatic Model PM1300TX Dust Collector. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide consistent, long-term operation if used in accordance with instructions set forth in this manual.

  • Page 6: Unpacking

    Unpacking Remove all contents from the shipping carton and check against the Contents of Shipping Carton below to verify that all items have been received. Report any damage to your distributor. Do not discard any shipping material until after the dust collector has been assembled and is running properly.

  • Page 7: Base Machine Assembly

    Note: Refer to Figure 3 to make sure that the Base Machine Assembly connector tube is facing the proper direction. 3. Insert an M8x20 hex cap screw (A), through the The dust collector must not be M8 washer (C) and flanges of the connector connected to the power source tube (O) and fan housing (K).

  • Page 8: Handles

    Filter System side. Tighten the screws. If your PM1300TX Dust Collection system includes Note: Make sure the plate (V) is oriented filter bags, proceed to Filter Bag System Assembly properly, as shown in the Detail in Figure 3: on page 9.

  • Page 9: Filter Bag System Assembly

    Filter Bag System Assembly Note: If your dust collection system includes the canister kit, proceed Canister System Assembly on page 10. 1. Insert a hanger bracket between support bar and collector housing (Figure 4). 2. Align holes and secure with two M8x20 hex cap screws and two M8 flat washers outside the housing, and two M8 flat washers and two M8 hex nuts inside the housing.

  • Page 10: Canister System Assembly

    6. Insert and tighten the four knobs into the Figure 10 threaded holes on the canister (Figure 10). Note: The Powermatic® label on the front of the canister should have a negligible effect upon air flow. However, if zero effect is desired, the label...

  • Page 11: Electrical Connections

    Extension Cords injury. If an extension cord is needed, make sure the The PM1300TX is equipped with a single phase, cord rating is suitable for the amperage listed on 115/230 volt motor. It is factory wired for 115 the machine’s motor plate. An undersize cord volts.

  • Page 12: Operating The Machine

    Dryer the face of the control panel. vent hose is not acceptable for this purpose. Contact your nearest Powermatic distributor for To operate the machine, use the buttons on the a full line of Dust Collector hoses and control panel, or use the provided remote control.

  • Page 13: Cleaning The Canister Filter

    Cleaning the Canister Filter Motor Clean the canister filter frequently to keep the Make frequent inspections of the motor fan and collector's performance at its optimum. To clean blow out (with low pressure air hose) or vacuum the filter, turn the handle a couple of rotations so any accumulation of foreign material in order to the dust falls into the clear plastic bag.

  • Page 14: Replacement Parts

    Replacement Parts are listed on the following pages. To order parts or reach our service department, call 1-800-274- 6848, Monday through Friday (see our website for business hours, www.powermatic.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.

  • Page 15: Parts List For Pm1300Tx Dust Collector (Base Machine)

    23 ..... 430035 ..... Rubber Gasket ..................1 24 ..... 430036 ..... Rubber Gasket ..................1 25 ..... PWBS14-254SN ..POWERMATIC Nameplate, Small ............1 26 ..... 31A-208-2 ....Strain Relief............PGA13.5 ..... 2 27 ..... PM1900-127 .... Handle ...................... 2 28 .....
  • Page 16 ....PM2700-440 .... Wide Stripe (not shown) ..............per ft....PM2700-441 .... Narrow Stripe (not shown) ..............per ft....PM1300-162 .... Powermatic Turbocone Decal (not shown) ..2-3/4”x8”...... 1 ....PM1300-BMHP ..Base Machine Hardware Package (not shown) * ........1 ....

  • Page 17: Breakdown For Pm1300Tx Canister Filter System

    Breakdown for PM1300TX Canister Filter System...

  • Page 18: Parts List For Pm1300Tx Canister Filter System

    23 ..... 331015 ..... Plate ......................2 24 ..... TS-1482021 ..... Hex Cap Screw ............ M6x12 ......4 ....PM1300-PLO ... Powermatic Label (not shown)......5-1/2x14 Oval ..... 1 ....PM1900-CHP ... Canister Hardware Package (not shown) * ..........1...

  • Page 19: Parts List For Pm1300Tx Filter Bag System

    Parts List for PM1300TX Filter Bag System Index No. Part No. Description Size ....1791077B ....PM1300 Collection and Filter Bag (includes #1 thru 5) ......1 1 ....1791077F ....Filter Bag .............. 30 micron ....1 2 ....410012 ..... Retainer Strap ..................1 3 ....

  • Page 20: Electrical Connections

    Electrical Connections...

  • Page 21: Warranty And Service

    Powermatic sells through distributors only. The specifications listed in Powermatic printed materials and on the official Powermatic website are given as general information and are not binding. Powermatic reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever.
  • Page 22 This page intentionally left blank...
  • Page 23 This page intentionally left blank...
  • Page 24 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.powermatic.com...

This manual is also suitable for:

1791078k1791079k

Table of Contents