Page 1
Video 2.5 HDD Product Manual Standard models ST500VT000 ST500VT001 ST320VT000 ST250VT000 100713733, Rev. J Gen 2.1 - September 2017...
Page 2
Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. 3D Defense System and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. The FIPS logo is a certification mark of NIST, which does not imply product endorsement by NIST, the U.S., or Canadian governments.
For information regarding online support and services, visit: http://www.seagate.com/contacts/ For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.com/services-software/recover/ For Seagate OEM, Distribution partner and reseller portals, visit: http://www.seagate.com/partners/ Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
Introduction This manual describes the functional, mechanical and interface specifications for the following: Seagate® Video 2.5 HDD model drives: Standard models ST500VT000 - 1DK142 ST500VT001 - 1K6142 ST320VT000 - 1DK14C ST250VT000 - 1DK141 These drives provide the following key features: ...
–304.8 m to 3048 m (–1000 ft to 10,000+ ft) Altitude, nonoperating –304.8 m to 12,192 m (–1000 ft to 40,000+ ft) (below mean sea level, max) Operational Shock 400 Gs at 2 ms max Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
19 Refer to Configuring and Mounting the Drive (words 60-61 and 100-103) for additional information about 48-bit addressing support of drives with capacities over 137 GB. Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
(such as track-to-track and average), are expected to meet the noted values. However, Note due to the manner in which these drives are formatted, benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications. Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. Standby power is measured at steady state (after 200ms from transition) Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 20 MHz. Equivalent resistance is calculated by dividing the nominal voltage by Note the typical RMS read/write current. 2.7.3 Voltage tolerance Voltage tolerance (including noise): +5V ± 5% Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
If the standby timer reaches zero before any drive activity is required, the drive makes a transition to standby mode. In both Idle and standby mode, the drive accepts all commands and returns to active mode when disk access is necessary. Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below. 5–500 Hz 5.0 Gs (0 to peak). Max displacement may apply below 22 Hz. Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
Test for prominent discrete tones (PDTs) Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards.
Seagate drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with all relevant regulatory requirements and standards for the drives, Seagate cannot guarantee that all system-level products into which the drives are installed comply with all regulatory requirements and standards applicable to the system-level products. The drive is designed for operation inside a properly designed system (e.g., enclosure designed for the drive), with properly shielded I/O cable (if...
2.12.6 Morocco Commodity Mark To satisfy our OEM customers, Seagate has added the Moroccan Commodity Mark to the drives provided to the OEM for the sale of Customer Kits produced by our OEM customers that are intended to be incorporated into the OEM's finished system-level product by an end user.
2.13.1.1 Restriction of Hazardous Substances in Electrical and Electronic Equipment Seagate drives are designed to be compliant with the European Union RoHS "Recast" Directive 2011/65/EU (RoHS 2) as amended by Directive (EU) 2015/863. The RoHS2 restricts the use of certain hazardous substances such as Lead, Cadmium, Mercury, Hexavalent Chromium, Polybrominated Biphenyls (PBB) and Polybrominated Diphenyl Ether (PBDE), BisBis(2-Ethylhexyl) phthalate (DEHP), Benzyl butyl phthalate (BBP), Dibutyl phthalate (DBP), and Diisobutyl phthalate (DIBP) in electrical and electronic equipment (EEE).
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%.
Figure 2 Attaching SATA Cabling Signal connector Power connector Signal cable Power cable Each cable is keyed to ensure correct orientation. Seagate Video 2.5 HDD drives support latching SATA connectors. Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
2X .118 in 2.99 mm BOTH SIDES .230 in 3.567 in 5.84 mm 90.60 mm .551 in 13.99 mm .263 in 6.68 mm 2.430 in 61.72 mm .160 in 4.06 mm Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
For detailed information about the Serial ATA interface, refer to the Serial ATA: High Speed Serialized AT Attachment specification. Hot-Plug Compatibility Seagate Video 2.5 HDD drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA: High Speed Serialized AT Attachment specification revision 2.0. This specification can be downloaded from .
Set Max Features register as defined to the right. Password: Lock: Unlock: Freeze Lock: Set Max Address Ext Set Multiple Mode S.M.A.R.T. Disable Operations B0h/D9h S.M.A.R.T. Enable/Disable Autosave B0h/D2h Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
Number of current logical heads xxxx Number of current logical sectors per logical track xxxx 57–58 Current capacity in sectors xxxx Number of sectors transferred during a xxxx Read Multiple or Write Multiple command Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
Page 26
Auto acoustic management setting xxxx Stream Min. Request Size 0000 Streaming Transfer Time - DMA 0000 Streaming Access Latency - DMA and PIO 0000 98-99 Streaming Performance Granularity 0000 Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
Page 27
Transport major version number 101F 223–254 ATA-reserved 0000 Integrity word xxA5 See the bit descriptions below for words 63, 88 and 93 of the Identify Drive data. (on next page) Note Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
Page 28
Ultra DMA mode 5 is currently active. Ultra DMA mode 6 is currently active. Word 93 1 = 80-conductor cable detected, CBLID above VIH 0 = 40-conductor cable detected, CBLID below VIL Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
Free Fall Protection feature) Report full capacity available At power-on, or after a hardware or software reset, the default Note values of the features are as indicated above Seagate Video 2.5 HDD Product Manual, Rev. J (Draft 1)
) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://www.seagate.com/support/downloads/seatools/. This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. to enable this feature.
Page 31
ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100713733, Rev. J (Draft 1)