1. Manuals
  2. Brands
  3. OV Solutions Manuals
  4. Security Camera
  5. C-OVE-6DVIR-FE
  6. User manual

OV Solutions C-OVE-6DVIR-FE User Manual

Network fisheye camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Network Fisheye Camera
User Manual

Advertisement

Table of Contents
loading

Related Manuals for OV Solutions C-OVE-6DVIR-FE

Summary of Contents for OV Solutions C-OVE-6DVIR-FE

  • Page 1 Network Fisheye Camera User Manual...
  • Page 2 User Manual of Network Fisheye Camera Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to network fisheye camera. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice.
  • Page 3 User Manual of Network Fisheye Camera Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 4 User Manual of Network Fisheye Camera Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected.
  • Page 5 User Manual of Network Fisheye Camera Cautions:  Make sure the power supply voltage is correct before using the camera.  Do not drop the camera or subject it to physical shock.  Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently.

  • Page 6: Table Of Contents

    User Manual of Network Fisheye Camera Table of Contents Chapter 1 System Requirement ................8 Chapter 2 Network Connection ................9 Setting the Network Camera over the LAN ............9 2.1.1 Wiring over the LAN ......................9 2.1.2 Detecting and Changing the IP Address ................10 Setting the Network Camera over the WAN ............
  • Page 7 User Manual of Network Fisheye Camera 5.3.12 Platform Access Setting ....................44 5.3.13 Configuring HTTPS Settings ..................... 44 Configuring Video and Audio Settings ............. 47 5.4.1 Configuring Video Settings ..................... 47 5.4.2 Configuring Audio Settings ..................... 48 5.4.3 Configuring ROI Encoding ....................49 5.4.4 Displaying Info on Stream ....................
  • Page 8 User Manual of Network Fisheye Camera 9.7.3 Exporting / Importing Configuration File ................ 87 9.7.4 Upgrading the System ..................... 88 RS-232 Settings ....................88 DST Settings ....................89 9.10 RS-485 Settings ....................90 9.11 Fisheye Parameters ..................91 Appendix ......................92 Appendix 1 SADP Software Introduction ..............

  • Page 9: Chapter 1 System Requirement

    User Manual of Network Fisheye Camera Chapter 1 System Requirement Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above versions.

  • Page 10: Chapter 2 Network Connection

    User Manual of Network Fisheye Camera Chapter 2 Network Connection Before you start:  If you want to set the network camera via a LAN (Local Area Network), please refer to Section 2.1 Setting the Network Camera over the LAN. ...

  • Page 11: Detecting And Changing The Ip Address

    User Manual of Network Fisheye Camera Figure 2-2 Connecting via a Switch or a Router 2.1.2 Detecting and Changing the IP Address You need the IP address to visit the network camera. Steps: 1. To get the IP address, you can choose either of the following methods: ...

  • Page 12: Setting The Network Camera Over The Wan

    User Manual of Network Fisheye Camera Figure 2-3 SADP Interface 2.2 Setting the Network Camera over the WAN Purpose: This section explains how to connect the network camera to the WAN with a static IP or a dynamic IP. 2.2.1 Static IP Connection Before you start: Please apply a static IP from an ISP (Internet Service Provider).

  • Page 13: Dynamic Ip Connection

    User Manual of Network Fisheye Camera 2. Assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2 Detecting and Changing the IP Address for detailed IP address configuration of the camera. 3. Save the static IP in the router. 4.
  • Page 14 User Manual of Network Fisheye Camera 1. Connect the network camera to the router. 2. In the camera, assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2 Detecting and Changing the IP Address for detailed LAN configuration.
  • Page 15 User Manual of Network Fisheye Camera Figure 2-7 Normal Domain Name Resolution Steps: 1. Apply a domain name from a domain name provider. 2. Configure the DDNS settings in the DDNS Settings interface of the network camera. Refer to Section 5.3.4 Configuring DDNS Settings for detailed configuration.

  • Page 16: Chapter 3 Access To The Network Camera

    User Manual of Network Fisheye Camera Chapter 3 Access to the Network Camera 3.1 Accessing by Web Browsers Steps: 1. Open the web browser. 2. Input the IP address of the network camera in the address bar, e.g., 192.0.0.64 and press the Enter key to enter the login interface. 3.
  • Page 17 User Manual of Network Fisheye Camera Figure 3-2 Download and Install Plug-in Figure 3-3 Install Plug-in (1) Figure 3-4 Install Plug-in (2) Note: You may have to close the web browser to install the plug-in. Please reopen the web browser and log in again after installing the plug-in.

  • Page 18: Accessing By Client Software

    User Manual of Network Fisheye Camera 3.2 Accessing by Client Software The product CD contains the NVMS7000 client software. You can view the live video and manage the camera with the software. Follow the installation prompts to install the software. The control panel interface of NVMS7000 client software is shown as bellow.

  • Page 19: Chapter 4 Live View

    User Manual of Network Fisheye Camera Chapter 4 Live View 4.1 Live View Page Purpose: The live view page allows you to view the real-time video, capture images, realize e-PTZ control, set/call presets and configure video parameters. Log in the network camera to enter the live view page, or you can click Live View on the menu bar of the main page to enter the live view page.

  • Page 20: Starting Live View

    User Manual of Network Fisheye Camera Live View Mode: Display the live video in Fisheye View, Panorama View, or PTZ View.  Fisheye View: In the Fisheye View mode, the whole wide-angle view of the fisheye camera is displayed. This view mode is called Fisheye View because it approximates the vision of a fish’s convex eye.

  • Page 21: Recording And Capturing Pictures Manually

    User Manual of Network Fisheye Camera Figure 4-2 Live View Interface Table 4-1 Descriptions of Live View Icons Icon Description The length-to-width ratio of image display window is 4:3. The length-to-width ratio of image display window is 16:9. Window size for original video stream. Self-adaptive window size.

  • Page 22: Operating E-Ptz Control

    User Manual of Network Fisheye Camera remote scheduled recording, please refer to Section 6.2. Note: The captured image will be saved as JPEG file or BMP file in your computer. 4.4 Operating e-PTZ Control Purpose: The PTZ View is the close-up view of some defined area on the panoramic / fisheye view, and it supports digital PTZ control, also called e-PTZ control function.

  • Page 23: Setting / Calling / Deleting A Preset

    User Manual of Network Fisheye Camera Figure 4-4 e-PTZ Control Panel Table 4-2 Descriptions of e-PTZ Control Panel Icon Description Direction Arrows Auto Scan Zoom in/out Adjust speed of pan/tilt movements Steps: 1. Click to select a PTZ View on the display window, and then the navigation box appears on the Fisheye View and Panorama View.
  • Page 24 User Manual of Network Fisheye Camera 1. Click to select a PTZ View on the display window. 2. Click the direction / zoom buttons on the e-PTZ Control panel to adjust the PTZ View as desired. 3. Select a preset number from the preset list. 4.

  • Page 25: Setting / Calling / Deleting A Patrol

    User Manual of Network Fisheye Camera Figure 4-6 Calling a Preset  Deleting a Preset Steps: 1. Select the preset number from the list. 2. Click the icon to delete the selected preset. The preset name turns from black to grey. Figure 4-7 Deleting a Preset 4.4.3 Setting / Calling / Deleting a Patrol Purpose:...
  • Page 26 User Manual of Network Fisheye Camera At least 2 presets are required to set a patrol.  Setting a Patrol Steps: 1. Click the icon to enter the patrol configuration interface. Figure 4-8 Patrol Configuration 2. Select a path No. from the drop-down list, and click the icon in the lower-left corner to add the presets as the key points.
  • Page 27 User Manual of Network Fisheye Camera Note: Up to 32 patrol paths can be set, and each path supporting 16 key points at most.  Calling a Patrol Steps: 1. Click to select a PTZ View on the display window. 2.

  • Page 28: Chapter 5 Network Camera Configuration

    User Manual of Network Fisheye Camera Chapter 5 Network Camera Configuration 5.1 Configuring Local Parameters Purpose: Local configuration provides live view parameters settings, record file settings and picture and clip settings. The recorded videos and captured pictures can be saved on the local PC running the web browser.
  • Page 29 User Manual of Network Fisheye Camera HTTP: Allows the same quality as of TCP without setting specific ports for streaming under some network environments. MULTICAST: It’s recommended to select MCAST type when using the Multicast function. For detailed information about Multicast, refer to Section 5.3.1 Configuring TCP/IP Settings.

  • Page 30: Configuring Time Settings

    User Manual of Network Fisheye Camera 3. Click Save to save the settings. 5.2 Configuring Time Settings Purpose: You can follow the instructions in this section to configure the time synchronization and DST settings. Steps: 1. Enter the Time Settings interface: Configuration >...
  • Page 31 User Manual of Network Fisheye Camera via NTP server. Figure 5-3 Time Sync by NTP Server Note: If the camera is connected to a public network, you should use a NTP server that has a time synchronization function, such as the server at the National Time Center (IP Address: 210.72.145.44).

  • Page 32: Configuring Network Settings

    User Manual of Network Fisheye Camera 5.3 Configuring Network Settings 5.3.1 Configuring TCP/IP Settings Purpose: TCP/IP settings must be properly configured before you operate the camera over network. The camera supports both the IPv4 and IPv6. Both versions may be configured simultaneously without conflicting to each other, and at least one IP version should be configured.

  • Page 33: Configuring Port Settings

    User Manual of Network Fisheye Camera Notes:  The valid value range of MTU is 1280 ~ 1500.  The Multicast sends a stream to the multicast group address and allows multiple clients to acquire the stream at the same time by requesting a copy from the multicast group address.

  • Page 34: Configuring Pppoe Settings

    User Manual of Network Fisheye Camera Server Port: The default server port number is 8000, and it can be changed to any port No. ranges from 2000 to 65535. 3. Click Save to save the settings. Note: A reboot is required for the settings to take effect. 5.3.3 Configuring PPPoE Settings Steps: 1.
  • Page 35 User Manual of Network Fisheye Camera Steps: 1. Enter the DDNS Settings interface: Configuration > Advanced Configuration > Network > DDNS Figure 5-8 DDNS Settings 2. Check the Enable DDNS checkbox to enable this feature. 3. Select DDNS Type. Four DDNS types are selectable: HiDDNS, IPServer , DynDNS and NO-IP.
  • Page 36 User Manual of Network Fisheye Camera  IP Server: Steps: (1) Enter the Server Address of the IP Server. (2) Click Save to save the settings. Note: For the IP Server, you have to apply a static IP, subnet mask, and gateway and preferred DNS from the ISP.
  • Page 37 User Manual of Network Fisheye Camera (5) Enter the User Name and Password. (6) Click Save and then you can view the camera with the domain name.  HiDDNS Steps: (1) Choose the DDNS Type as HiDDNS. Figure 5-12 HiDDNS Settings (2) Enter the Server Address www.hiddns.com.

  • Page 38: Configuring Snmp Settings

    User Manual of Network Fisheye Camera 5.3.5 Configuring SNMP Settings Purpose: You can set the SNMP function to get camera status, parameters and alarm related information and manage the camera remotely when it is connected to the network. Before you start: Before setting the SNMP, please download the SNMP software and manage to receive the camera information via SNMP port.

  • Page 39: Configuring 802.1X Settings

    User Manual of Network Fisheye Camera 2. Check the corresponding version checkbox ( ) to enable the feature. 3. Configure the SNMP settings. Note: The settings of the SNMP software should be the same as the settings you configure here. 4.

  • Page 40: Configuring Qos Settings

    User Manual of Network Fisheye Camera 3. Configure the 802.1X settings, including EAPOL version, user name and password. Note: The EAPOL version must be identical with that of the router or the switch. 4. Enter the user name and password to access the server. 5.

  • Page 41: Configuring Upnp™ Settings

    User Manual of Network Fisheye Camera 5.3.8 Configuring UPnP™ Settings Universal Plug and Play (UPnP™) is a networking architecture that provides compatibility among networking equipment, software and other hardware devices. The UPnP protocol allows devices to connect seamlessly and to simplify the implementation of networks in the home and corporate environments.
  • Page 42 User Manual of Network Fisheye Camera 1. Enter the TCP/IP Settings Configuration > Basic Configuration > Network > TCP/IP or Configuration > Advanced Configuration > Network > TCP/IP) to set the IPv4 Address, IPv4 Subnet Mask, IPv4 Default Gateway and the Preferred DNS Server.

  • Page 43: Configuring Nat Settings

    User Manual of Network Fisheye Camera Enable SSL: Check the checkbox to enable SSL if it is required by the SMTP server. Attached Image: Check the checkbox of Attached Image if you want to send emails with attached alarm images. Interval: The interval refers to the time between two actions of sending attached pictures.

  • Page 44: Configuring Ftp Settings

    User Manual of Network Fisheye Camera Figure 5-19 Configure NAT Settings 3. Click Save to save the settings. 5.3.11 Configuring FTP Settings Purpose: You can configure the FTP server related information to enable the uploading of the captured pictures to the FTP server. The captured pictures can be triggered by events or a timing snapshot task.

  • Page 45: Platform Access Setting

    User Manual of Network Fisheye Camera Camera Name or Camera No. as the name of the directory. Upload type: To enable uploading the captured picture to the FTP server. Anonymous Access to the FTP Server (in which case the user name and password won’t be required.): Check the Anonymous checkbox to enable the anonymous access to the FTP server.
  • Page 46 User Manual of Network Fisheye Camera communicating with, which protects against Man-in-the-middle attacks. Perform the following steps to set the port number of https. E.g: If you set the port number as 443 and the IP address is 192.0.0.64, you may access the device by inputting https://192.0.0.64:443 via the web browser.
  • Page 47 User Manual of Network Fisheye Camera Figure 5-23 Create Self-signed Certificate (2) Enter the country, host name/IP, validity and other information. (3) Click OK to save the settings. Note: If you already had a certificate installed, the Create Self-signed Certificate is grayed out. ...

  • Page 48: Configuring Video And Audio Settings

    User Manual of Network Fisheye Camera 5.4 Configuring Video and Audio Settings 5.4.1 Configuring Video Settings Steps: 1. Enter the Video Settings interface: Configuration >Basic Configuration > Video / Audio > Video Or Configuration > Advanced Configuration > Video / Audio > Video Figure 5-25 Configure Video Settings 2.

  • Page 49: Configuring Audio Settings

    User Manual of Network Fisheye Camera Frame Rate: Set the frame rate to 1/16~25 fps. The frame rate is to describe the frequency at which the video stream is updated and it is measured by frames per second (fps). A higher frame rate is advantageous when there is movement in the video stream, as it maintains image quality throughout.

  • Page 50: Configuring Roi Encoding

    User Manual of Network Fisheye Camera Figure 5-26 Audio Settings 2. Configure the following settings. Audio Encoding: G.711 ulaw, G.711alaw, G.726, G.722.1 and MP2L2 are selectable. And 32kbps, 64kbps, and 128kbps are supported if MP2L2 is selected. Audio Input: MicIn and Linein are selectable for the connected microphone and pickup respectively.

  • Page 51: Displaying Info On Stream

    User Manual of Network Fisheye Camera Figure 5-27 Region of Interest Settings 2. Check the checkbox of Enable under Fixed Region item. 3. Select the stream type for ROI encoding. 4. Select the region No. from the drop-down list for ROI settings. There are four fixed regions selectable.

  • Page 52: Configuring Image Parameters

    User Manual of Network Fisheye Camera Figure 5-28 Display Info on Stream 5.5 Configuring Image Parameters 5.5.1 Configuring Display Settings Purpose: You can set the image quality of the camera, including brightness, contrast, saturation, hue, sharpness, etc. Note: The display parameters vary according to the different camera model. Please refer to the actual interface for details.
  • Page 53 User Manual of Network Fisheye Camera Figure 5-29 Display Settings of Day/night Auto-switch  Image Adjustment Brightness describes bright of the image, which ranges from 1~100, and the default value is 50. Contrast describes the contrast of the image, which ranges from 1~100, and the default value is 50.
  • Page 54 User Manual of Network Fisheye Camera Day: the camera stays at day mode. Night: the camera stays at night mode. Auto: the camera switches between the day mode and the night mode according to the illumination automatically. The sensitivity ranges from 0~7, the higher the value is, the easier the mode switches.

  • Page 55: Configuring Osd Settings

    User Manual of Network Fisheye Camera Digital Noise Reduction: DNR reduces the noise in the video stream. Select ON/ OFF to enable / disable the digital noise reduction function. If the function is enabled, set the DNR level from 0 to 100, and the default value is 50. ...

  • Page 56: Configuring Text Overlay

    User Manual of Network Fisheye Camera 3. Edit the camera name in the text field of Camera Name. 4. Select from the drop-down list to set the time format, date format, display mode and the OSD font size. 5. You can use the mouse to click-and-drag the Time and Camera Name text frames in the live view window to adjust the OSD position.

  • Page 57: Configuring Privacy Mask

    User Manual of Network Fisheye Camera window to adjust the text overlay position. 5. Click Save to save the settings. Note: Up to 4 text overlays are configurable. 5.5.4 Configuring Privacy Mask Purpose: Privacy mask enables you to cover certain areas on the live video to prevent certain spots in the surveillance area from being live viewed and recorded.

  • Page 58: Configuring And Handling Alarms

    User Manual of Network Fisheye Camera 5.6 Configuring and Handling Alarms This section explains how to configure the network camera to respond to alarm events, including motion detection, video tampering, alarm input, alarm output, exception, face detection, audio exception detection, intrusion detection, defocus detection, and scene change detection, etc.
  • Page 59 User Manual of Network Fisheye Camera 3. (Optional) Check the checkbox of Enable Dynamic Analysis for Motion if you want to mark the detected objects with green rectangles on the live view window. Note: You can go to Configuration > Local Configuration > Live View Parameters >...
  • Page 60 User Manual of Network Fisheye Camera (6) You can click Clear All to clear all of the configured areas.  Expert Mode If Expert is selected as the configuration mode, different sets of parameters are adopted for motion detection at day and night. Figure 5-35 Motion Detection Settings-Expert Mode (1) Set the Day&Night switch mode, there are OFF, Auto-Switch and Scheduled-Switch selectable.
  • Page 61 User Manual of Network Fisheye Camera Figure 5-36 Arming Schedule Steps: (1) Click Edit to edit the arming schedule. Figure 5-37 Schedule Time Settings (2) Choose the day you want to set the arming schedule. (3) Click to set the time period for the arming schedule. (4) (Optional) After you set the arming schedule, you can copy the schedule to other days.

  • Page 62: Configuring Video Tampering Alarm

    User Manual of Network Fisheye Camera Figure 5-38 Linkage Method  Notify Surveillance Center Send an exception or alarm signal to remote management software when an event occurs.  Send Email Send an email with alarm information to a user or users when an event occurs. Note: To send the Email when an event occurs, you need to refer to Section 5.3.9 to set the related parameters.
  • Page 63 User Manual of Network Fisheye Camera You can configure the camera to trigger the alarm when the lens is covered and take alarm response action. Steps: 1. Enter the Tamper-proof Settings interface: Configuration > Advanced Configuration > Events > Video Tampering 2.

  • Page 64: Configuring Alarm Input

    User Manual of Network Fisheye Camera 5.6.3 Configuring Alarm Input Steps: 1. Enter the Alarm Input Settings interface: Configuration > Advanced Configuration> Events > Alarm Input: 2. Choose the alarm input No. and the Alarm Type. The alarm type can be NO (Normally Open) and NC (Normally Closed).

  • Page 65: Handling Exception

    User Manual of Network Fisheye Camera Manual. The delay time refers to the time duration that the alarm output remains in effect after alarm occurs. 5. Click Edit to set the arming schedule for the alarm output. For details, refer to Step 5 in Section 5.6.1.

  • Page 66: Configuring Line Crossing Detection

    User Manual of Network Fisheye Camera 3. Click Save to save the settings. 5.6.6 Configuring Line Crossing Detection Purpose: Line crossing detection function detects people, vehicle or other objects which cross a pre-defined virtual line, and some certain actions can be taken when the alarm is triggered.

  • Page 67: Configuring Intrusion Detection

    User Manual of Network Fisheye Camera Surveillance Center, Send Email, Upload to FTP, Trigger Channel and Trigger Alarm Output. 11. Click Save to save the settings. Figure 5-43 Line Crossing Detection Settings 5.6.7 Configuring Intrusion Detection Purpose: Intrusion detection function detects people, vehicle or other objects which enter and loiter in a pre-defined virtual region, and some certain actions can be taken when the alarm is triggered.
  • Page 68 User Manual of Network Fisheye Camera 5. Set the time threshold, detection sensitivity and object percentage for intrusion detection. Threshold: Range [0-10]s, the threshold for the time of the object loitering in the region. If you set the value as 0, alarm is triggered immediately after the object entering the region.

  • Page 69: Chapter 6 Storage Settings

    User Manual of Network Fisheye Camera Chapter 6 Storage Settings Before you start: To configure record settings, please make sure that you have the network storage device within the network or the SD card inserted in your camera. 6.1 Configuring NAS Settings Before you start: The network disk should be available within the network and properly configured to store the recorded files, log files, etc.
  • Page 70 User Manual of Network Fisheye Camera You can view the capacity, free space, status, type and property of the disk. Figure 6-2 Storage Management Interface (2) If the status of the disk is Uninitialized, check the corresponding checkbox to select the disk and click Format to start initializing the disk. When the initialization completed, the status of disk will become Normal.

  • Page 71: Configuring Recording Schedule

    User Manual of Network Fisheye Camera 6.2 Configuring Recording Schedule Purpose: There are two kinds of recording for the cameras: manual recording and scheduled recording. For the manual recording, refer to Section 4.3 Recording and Capturing Pictures Manually. In this section, you can follow the instructions to configure the scheduled recording.
  • Page 72 User Manual of Network Fisheye Camera event. For example, if an alarm triggered recording ends at 11:00, and the post-record time is set as 5 seconds, the camera records until 11:00:05. The Post-record time can be configured as 5 s, 10 s, 30 s, 1 min, 2 min, 5 min or 10 min.
  • Page 73 User Manual of Network Fisheye Camera (2) Select a Record Type. The record type can be Continuous, Motion Detection, Alarm, Motion | Alarm, Motion & Alarm, etc.  Continuous If you select continuous, the video will be recorded automatically according to the time of the schedule.

  • Page 74: Configuring Snapshot Settings

    User Manual of Network Fisheye Camera settings on the Motion Detection and Alarm Input Settings interfaces. Please refer to Section 5.6.1 and Section 5.6.3 for detailed information.  Record Triggered by Line Crossing Detection If you select Line Crossing Detection, the video will be recorded when the line crossing event is detected.
  • Page 75 User Manual of Network Fisheye Camera Steps: 1. Enter the Snapshot Settings interface: Configuration > Advanced Configuration > Storage > Snapshot 2. Check the Enable Timing Snapshot checkbox to enable scheduled snapshot. 3. Select picture format, resolution, and quality for the snapshots. 4.
  • Page 76 User Manual of Network Fisheye Camera please refer to Section 5.6. Steps: 1. Enter the Snapshot Settings interface: Configuration > Advanced Configuration > Storage > Snapshot 2. Check the Enable Event-triggered Snapshot checkbox to enable event-triggered snapshot. 3. Select picture format, resolution, and quality for the snapshots. 4.

  • Page 77: Chapter 7 Playback

    User Manual of Network Fisheye Camera Chapter 7 Playback Purpose: This section explains how to view the remotely recorded video files stored in the network disks or SD cards. Steps: 1. Click Playback on the menu bar to enter playback interface. Figure 7-1 Playback Interface 2.
  • Page 78 User Manual of Network Fisheye Camera Figure 7-3 Playback Toolbar Table 7-1 Description of Playback Icons Icon Description Start / Pause the video playback. Stop the video playback. Decrease / Increase the speed of video playback. Play the video back frame by frame. Manually capture the picture during playback.
  • Page 79 User Manual of Network Fisheye Camera Figure 7-5 Progress Bar Different video types are marked in different colors on the progress bar. Figure 7-6 Video Types...

  • Page 80: Chapter 8 Log Searching

    User Manual of Network Fisheye Camera Chapter 8 Log Searching Purpose: The operation, alarm, exception and information of the camera can be stored in log files. You can also export the log files on your demand. Before you start: Please configure network disk for the camera or insert a SD card in the camera. Steps: 1.

  • Page 81: Chapter 9 Others

    User Manual of Network Fisheye Camera Chapter 9 Others 9.1 Managing User Accounts Enter the User Management interface: Configuration >Basic Configuration> Security > User Or Configuration > Advanced Configuration> Security > User The admin user has access to create, modify or delete other accounts. Up to 31 user accounts can be created.
  • Page 82 User Manual of Network Fisheye Camera Figure 9-2 Add a User Modify a User Steps: 1. Click to select the user from the list and click Modify. 2. Modify the User Name, Level or Password. 3. In the Basic Permission field and Camera Configuration field, you can check or uncheck the permissions.

  • Page 83: Configuring Rtsp Authentication

    User Manual of Network Fisheye Camera Delete a User Steps: 1. Click to select the user you want to delete and click Delete. 2. Click OK on the pop-up dialogue box to delete the user. 9.2 Configuring RTSP Authentication Purpose: You can specifically secure the stream data of live view.

  • Page 84: Ip Address Filter

    User Manual of Network Fisheye Camera Steps: 1. Enter the Anonymous Visit interface: Configuration> Advanced Configuration> Security > Anonymous Visit Figure 9-5 Anonymous Visit 2. Set the Anonymous Visit permission Enable or Disable in the drop-down list to enable or disable the anonymous visit. 3.
  • Page 85 User Manual of Network Fisheye Camera Figure 9-7 IP Address Filter Interface 2. Check the checkbox of Enable IP Address Filter. 3. Select the type of IP Address Filter in the drop-down list, Forbidden and Allowed are selectable. 4. Set the IP Address Filter list. ...

  • Page 86: Security Service

    User Manual of Network Fisheye Camera  Delete an IP Address Left-click an IP address from filter list and click Delete.  Delete all IP Addresses Click Clear to delete all the IP addrsses. 5. Click Save to save the settings. 9.5 Security Service Purpose: To enable the remote login, and improve the data communication security, the...

  • Page 87: Maintenance

    User Manual of Network Fisheye Camera Other information of the network camera, such as Model, Serial No., Firmware Version, Encoding Version, Number of Channels, Number of HDDs, Number of Alarm Input and Number of Alarm Output are displayed. The information cannot be changed in this menu.

  • Page 88: Restoring Default Settings

    User Manual of Network Fisheye Camera 9.7.2 Restoring Default Settings Steps: 1. Enter the Maintenance interface: Configuration > Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Maintenance 2. Click Restore or Default to restore the default settings. Figure 9-13 Restore Default Settings Note: After restoring the default settings, the IP address is also restored to...

  • Page 89: Upgrading The System

    User Manual of Network Fisheye Camera Figure 9-14 Import/Export Configuration File 9.7.4 Upgrading the System Steps: 1. Enter the Maintenance interface: Configuration > Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Maintenance 2. Click Browse to select the local upgrade file and then click Upgrade to start remote upgrade.

  • Page 90: Dst Settings

    User Manual of Network Fisheye Camera device will be controlled remotely by the computer through the network. Steps: 1. Enter RS-232 Port Setting interface: Configuration> Advanced Configuration> System > RS232 Figure 9-16 RS-232 Settings Note: If you want to connect the camera by the RS-232 port, the parameters of the RS-232 should be exactly the same with the parameters you configured here.

  • Page 91: Rs-485 Settings

    User Manual of Network Fisheye Camera Figure 9-17 DST Settings 9.10 RS-485 Settings Purpose: The RS-485 serial port is used to control the PTZ of the camera. The configuring of the PTZ parameters should be done before you control the PTZ unit. Note: RS-485 settings vary according to the camera model.

  • Page 92: Fisheye Parameters

    User Manual of Network Fisheye Camera Figure 9-18 RS-485 Settings 9.11 Fisheye Parameters Steps: 1. Enter Fisheye Parameters interface: Configuration> Advanced Configuration> System > Fisheye Parameters 2. Select the mounting type of the fisheye camera according to your actual environment and demand. Ceiling mounting, table mounting, and wall mounting are selectable for the mounting type.

  • Page 93: Appendix

    User Manual of Network Fisheye Camera Appendix Appendix 1 SADP Software Introduction  Description of SADP V 2.0 SADP (Search Active Devices Protocol) is a kind of user-friendly and installation-free online device search tool. It searches the active online devices within your subnet and displays the information of the devices.
  • Page 94 User Manual of Network Fisheye Camera online; it will be removed from the list in 45 seconds after it went offline.  Search online devices manually You can also click Refresh to refresh the online device list manually. The newly searched devices will be added to the list. Note: You can click on each column heading to order the...
  • Page 95 User Manual of Network Fisheye Camera Steps: 1. Contact our technical engineers to get the serial code. 2. Input the code in the Serial code field and click Confirm to restore the default password.

  • Page 96: Appendix 2 Port Mapping

    User Manual of Network Fisheye Camera Appendix 2 Port Mapping The following settings are for TP-LINK router (TL-WR641G). The settings vary depending on different models of routers. Steps: 1. Select the WAN Connection Type, as shown below: Figure A.2.1 Select the WAN Connection Type 2.
  • Page 97 User Manual of Network Fisheye Camera another camera as 81, 8001, 555, 8201 with IP 192.168.1.24. Refer to the steps as below: Steps: 1. As the settings mentioned above, map the port 80, 8000, 554 and 8200 for the network camera at 192.168.1.23 2.

Table of Contents