Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Digitalchina Networks WL8200 Series
- Page 1 802.11AC Wireless Access Point Installation Manual Manual Version: v1.0...
-
Page 2: Table Of Contents
3.2 Checking before Installation ............3-2 3.3 Ensure the Installation Position ............ 3-2 3.4 Install WL8200 Series ..............3-2 3.4.1 Wall Hanging Installation ..............3-2 3.4.2 T-keel Installation .................. 3-3 3.5 Connect AP Power ................3-5 ... -
Page 3: Chapter 1 Device Introduction
Chapter 1 Device Introduction Chapter 1 Device Introduction WL8200 Series Wireless AP ( Access Point) is the new 1000Mb wireless AP device based on 802.11n and 802.11AC standard with high performance from DigitalChina Networks Limited (DCN). 802.11AC Wireless Access Point can work in the band of 2.4GHz and 5GHz. - Page 4 Built-in antenna: Using USB: ≤20W • Double Radiofrequency •2.4G gain 4.5dBi •5G gain 4.5dBi The shape size and weight of WL8200 series indoor AP is as below: Table 1-2 the shape size and weight Shape Size Weight Product Model WL8200 series（W×D×H）...
-
Page 5: Chapter 2 Preparation For Installation
802.11AC Wireless Access Point Installation Manual Chapter 2 Preparation for Installation Chapter 2 Preparation for Installation 2.1 Installation Precautions Only allow the professionals installing and disassembling the device and its annex. Before the installation and configuration, please read the related security introduction carefully. -
Page 6: Installation Environment Requirements
-10℃～55℃ Storage temperature -40℃～70℃ Working humidity (non-condensing) 5%～95% 2.3 Equipment Accessories Please refer to the packing list. 2.4 Installation Tools When installing WL8200 series indoor AP, the following tools may be used (user-owned). Horizontal Permanent Knife Wire Network pliers ruler... - Page 7 802.11AC Wireless Access Point Installation Manual Chapter 2 Preparation for Installation Impact drill (1) Rubber Phillips Ladder and some hammer screwdriver supporting drills...
-
Page 8: Chapter 3 Ap Installation
Chapter 3 AP Installation Chapter 3 AP Installation Because the installation position of WL8200 series indoor AP is high normally, the maintenance personal cannot maintain and debug through the console port to login the device after installation. We suggest user conducting the basic configuration according to need before installing the AP to the appointed position. -
Page 9: Checking Before Installation
If there is outdoor cable, please check if installed the network port SPD beside the AP, the network port SPD should be provided by user. 3.4 Install WL8200 Series WL8200 Series can be installed indoor only and there are two methods supported: Wall hanging installation T-keel installation 3.4.1 Wall Hanging Installation... -
Page 10: T-Keel Installation
802.11AC Wireless Access Point Installation Manual Chapter 3 AP Installation Fig 3-2 wall mounting screws When installed with wall hanging method, please connect the Ethernet cable to the AP first and then install the AP on the wall mounting bracket. (1) Connect the AP to the wired LAN by using the cable (2) Mark the positions of two holes on the wall and the distance between them is 65 mm. - Page 11 Fig 3-4 mounting kit WL8200 series AP provides two kinds of mounting kits whose width are 15cm and 24cm. The client can choose the right mounting kit according to the actual installation scenario.
-
Page 12: Connect Ap Power
Fig 3-7 Complete the AP installation 3.5 Connect AP Power WL8200 series indoor AP support the local power and PoE power. User can choose the method according to the actual network environment. 3.5.1 Checking before Power After installing the AP, user should check it before power every time as below: When AP use the local power, please ensure the power is connected normally to ground. -
Page 13: Local Power
PoE function to power to the AP. WL8200 series adopts the 802.3af/802.3at PoE power supply. When the USB is not used, it adopts the 802.3af PoE power supply; if the USB is used, it should adopt the 802.3at PoE power supply. -
Page 14: Connect Ap To Internet
802.11AC Wireless Access Point Installation Manual Chapter 3 AP Installation 3.6 Connect AP to Internet In the actual use, AP can be uplink connected to the Internet or MAN through the Ethernet port. Connect the Ethernet port of the AP to the switch port to achieve the uplink connection.