Makita DSS610Z Instruction Manual
Cordless circular saw
Hide thumbs
Also See for DSS610Z:
- Instruction manual (69 pages) ,
- Instruction manual (73 pages) ,
- Instruction manual (40 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DSS610Z
Summary of Contents for Makita DSS610Z
- Page 1 Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Makita DSS610 DSS610Z o cerca il tuo prodotto tra le migliori offerte di Elettroutensili INSTRUCTION MANUAL Cordless Circular Saw DSS610 DSS611 006699 IMPORTANT: Read Before Using.
-
Page 2: Specifications
For European countries only ENG905-1 Noise EC Declaration of Conformity The typical A-weighted noise level determined according Makita declares that the following Machine(s): to EN60745: Designation of Machine: Sound pressure level (L ) : 78 dB (A) Cordless Circular Saw Uncertainty (K) : 3 dB (A) Model No./ Type: DSS610, DSS611... -
Page 3: General Power Tool Safety Warnings
The technical file in accordance with 2006/42/EC is When operating a power tool outdoors, use an available from: extension cord suitable for outdoor use. Use of Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium a cord suitable for outdoor use reduces the risk of electric shock. 31.12.2013... - Page 4 GEB060-5 20. Store idle power tools out of the reach of children and do not allow persons unfamiliar CORDLESS CIRCULAR SAW with the power tool or these instructions to SAFETY WARNINGS operate the power tool. Power tools are dangerous in the hands of untrained users. Cutting procedures 21.
- Page 5 Kickback causes and related warnings kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator; when the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator;...
- Page 6 19. Check the operation of the lower guard spring. If the guard and the spring are not operating Fig. 2 properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a build-up of debris. 20.
-
Page 7: Functional Description
the safety rules stated in this instruction manual may FUNCTIONAL DESCRIPTION cause serious personal injury. ENC007-7 CAUTION: IMPORTANT SAFETY Always be sure that the tool is switched off and the • INSTRUCTIONS battery cartridge is removed before adjusting or checking function on the tool. FOR BATTERY CARTRIDGE Installing or removing battery cartridge Before using battery cartridge, read all instructions... - Page 8 Battery protection system Bevel cutting (Lithium-ion battery with star marking) 1. Lever 1. Star marking 006702 For Model DSS610 012128 Lithium-ion batteries with a star marking are equipped 1. Stopper 0-45 0-50 with a protection system. This system automatically cuts off power to the tool to extend battery life.
-
Page 9: Switch Action
• the lock-off lever and pull the switch trigger. Release the at the front of the tool. switch trigger to stop. Use only the Makita wrench to install or remove the • blade. WARNING: To remove the blade, press the shaft lock so that the blade... -
Page 10: Operation
006712 Rip fence (Guide rule) When you wish to perform clean cutting operation, connect a Makita vacuum cleaner to your tool. Install the 1. Clamping screw dust nozzle on the tool using the screw. Then connect a 2. Rip fence (Guide... -
Page 11: Maintenance
90 CAUTION: These accessories or attachments are recommended • for use with your Makita tool specified in this manual. The use of any other accessories or attachments might 013953 present a risk of injury to persons. Only use accessory 1. - Page 12 Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan www.makita.com 885250A222...