Troubleshooting; Before Calling For Service - LG DLEX7710 E Series Owner's Manual

Table of Contents

Advertisement

Available languages

Available languages

TROUBLESHOOTING

Before Calling For Service

Your dryer is equipped with an automatic error-monitoring system to detect and diagnose problems at an early
stage. If your dryer does not function properly or does not function at all, check the following before you call for
service.
Problem
Dryer will not
• Power cord is not properly
turn on
plugged in.
• house fuse is blown, circuit
breaker has tripped, or power
outage has occurred.
Dryer does not
• house fuse is blown, circuit
heat
breaker has tripped, or power
outage has occurred.
• Gas supply or service turned off
(gas models only).
Greasy or dirty
• Fabric softener used incorrectly.
spots
• Clean and dirty clothes being
on clothes
dried together.
Display shows
• Thermistor is malfunctioning.
error
code tE1 or tE2
Lint on clothes
• Lint filter not cleaned properly.
• Laundry not sorted properly.
• Excess static in clothes.
• Dryer is overloaded.
• Tissue, paper, etc., left in pockets.
Excess static in
• Fabric softener not used or used
c l o t h e s a f te r
incorrectly.
drying
• Clothes dried too long
(overdried).
• Drying synthetics, permanent
press, or synthetic blends.
Display shows
• Power cord connection is
error
incorrect.
code PS
Drying time is
• heat settings, load size, or
not consistent
dampness of clothing is not
consistent.
Possible Causes
Solutions
• Make sure that the plug is plugged securely into a
grounded outlet matching the dryer's rating plate.
• Reset circuit breaker or replace fuse. Do not increase
fuse capacity. If the problem is a circuit overload, have it
corrected by a qualified electrician.
• Reset circuit breaker or replace fuse. Do not increase
fuse capacity. If the problem is a circuit overload, have it
corrected by a qualified electrician.
• Confirm that the house gas shutoff and the dryer gas
shutoff are both fully open.
• Confirm and follow the instructions provided with your
fabric softener.
• Make sure to use your dryer to dry only clean items,
because dirty items can soil clean clothes placed in the
same or subsequent loads.
• Stains on dried clothes are actually stains that were not
removed during the washing process.
Make sure that clothes are being completely cleaned
according to the instructions for your washer and
detergent.
• Turn off the dryer and call for service.
• Make sure the lint filter is cleaned before every load. With
some loads that produce high amounts of lint, it may be
necessary to clean the filter during the cycle.
• Some fabrics are lint producers (i.e., a fuzzy white cotton
towel) and should be dried separately from clothes that
are lint trappers (i.e., a pair of black linen pants).
• See the Excess static in clothes after drying section below.
• Divide larger loads into smaller loads for drying.
• Check pockets thoroughly before washing and drying
clothes.
• Use a fabric softener to reduce static electricity correctly.
Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
• Overdrying a load of laundry can cause a buildup of static
electricity. Adjust settings and use a shorter drying time,
or use Sensor Dry cycles.
• These materials can cause static buildup. Try using a fabric
softener.
• Check the connection of power cord to the terminal block.
Refer to pages in 29-33 this manual.
• The drying time for a load will vary depending on the heat
setting, the type of heat used (electric, natural gas, or LP
gas), the size of the load, the type of fabrics, the wetness
of the clothes, and the condition of the exhaust ducts and
lint filter.
TrOuBLESHOOTiNg
53

Advertisement

Chapters

Table of Contents
loading

This manual is also suitable for:

Dlgx7711 e seriesDlex7710ve

Table of Contents