Cycle Settings And Options; Special Functions - LG DLEX7710 E Series Owner's Manual

Cycle Settings and Options

Sensor dry cycles have preset settings that are selected
automatically. Manual dry cycles have default settings, but
you may also customize the settings using the cycle modifier
buttons. Press the button for that option to view and select
other settings.
NOTE
To protect your garments, not every dryness level,
temperature, or option is available with every cycle.
See the Cycle Guide for details.
Dry Level
Selects the level of dryness for the cycle. Press the Dry Level
button repeatedly to scroll through available settings.
• This option is only available with sensor dry cycles.
• The dryer will automatically adjust the cycle time. Selecting
More Dry or Very Dry will increase the cycle time, while Less
Dry or Damp Dry will decrease the cycle time.
• Use a Less Dry or Damp Dry setting for items that you wish to
iron.
Temp. Control
Adjusts the temperature setting from Ultra Low to High.
This allows precise care of your fabrics and garments. Press the
Temp. Control button repeatedly to scroll through available
settings.
Time Dry
Allows you to manually select the drying time, from 20 to 60
minutes, in 10-minute increments. Use this for small loads or to
remove wrinkles. Use the More Time/Less Time buttons to add
or reduce the drying time in 1-minute increments.
Your dryer features several additional cycle options to
customize cycles to meet your individual needs. Certain option
buttons also feature a special function that can be activated by
pressing and holding that option button for 3 seconds.
To Add Cycle Options to a Cycle:
1. Turn on the dryer and press the cycle buttons to select the
desired cycle.
2. Use the cycle modifier buttons to adjust the settings for that
cycle.
3. Press the cycle option buttons for the options you would like
to add. A confirmation message shows in the display.
4. Press the Start/Pause button to start the cycle. The dryer
starts automatically.
Wrinkle Care
Selecting this option will tumble the load periodically for up to
three hours after the selected cycle, or until the door is opened.
This is helpful in preventing wrinkles when you are unable to
remove items from the dryer immediately.
Signal
To turn the Signal off, press the Signal On/Off button. Press
again to turn the Signal back on.
Damp Dry Signal
With this option, the dryer signals when the load is
approximately 80% dry. This allows you to remove faster-
drying lightweight items or items that you would like to iron
or hang while still slightly damp.

Special Functions

The option buttons also activate special functions,
including Child Lock, Rack Dry and Drum Light.
Select the option by pressing the option button. Press
and hold the option button for special features marked
with the asterisk (*), such as Child Lock.
* Rack Dry
Use Rack Dry with items, such as wool sweaters, silk, and
lingerie, that should dry flat. Rack Dry can also be used
with items that should not be tumbled dry, such as gym
shoes or stuffed animals.
NOTE
NEVER tumble dry a load of clothing with the rack
installed. When the rack is installed, the drum will
rotate as usual, but the rack will not move. Make sure
all articles to be dried remain completely on the rack
and cannot fall off or be pulled off by the turning
drum. Be sure to remove the rack after use.
To install the drying rack:
1. With the dryer door open, slide the rack into the dryer
drum.
2. Make sure it is seated evenly on the edge of the inner
door rim and resting flat on the inside of the dryer.
* Child Lock
Use this option to prevent unwanted use of the dryer or to
keep cycle settings from being changed while the dryer is
operating. Press and hold the Reduce Static button for 3
seconds to activate or deactivate the Child Lock function.
The Child Lock icon will be shown in the display, and all
controls are disabled except the Power button.
NOTE
Once set, Child Lock remains active until it is manually
deactivated. Child Lock must be turned off to run
another cycle. To deactivate Child Lock, press and
hold the Reduce Static button for three seconds.
41
HOW TO uSE