Limited Warranty ... 48 Appendix ... 49 Power Cord Safety Guidelines ... 49 Compliance Information for U.S.A..50 Compliance Information for Canada ... 50 Compliance Information for European Countries ... 50 User Information for all Countries ... 50 ViewSonic PJ1165...
DPMS and DDC are trademarks of VESA. PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation. Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.
Contact your dealer anything is missing. NOTE • Keep the original packing material for future reshipment. For moving the projector, be sure to use the original packing material. Use special caution for the lens part. ViewSonic PJ1165...
CONTROL port NETWORK port AUDIO IN R/L port VIDEO IN port S-VIDEO port COMPONENT port RGB OUT port AUDIO OUT port REMOTE CONTROL port DC OUT port AC inlet Power switch Remote sensor Control buttons See the following page. ViewSonic PJ1165...
When you release the elevator buttons, the elevator feet will lock into position. As necessary, you can also finely adjust the height of the projector by twisting the elevator feet by hand. Elevator feet Elevator buttons ViewSonic PJ1165...
• Please take advantage of this function by connecting the accessory RGB cable to the RGB port (DDC 1/2B compatible). Plug-and-Play may no t work properly if any other type of connection is attempted. • Please use the standard drivers in your computer, as this projector is a Plug-and-Play monitor. ViewSonic PJ1165...
RS-232C cable RS-232C port CAT-5 cable Network port If using a M1-D input DVI port M1-D cable USB port Audio out Stereo Mini cable If using a BNC input RGB out BNC cable Stereo Mini cable Audio out Projector ViewSonic PJ1165...
Page 11
S-video out S-video cable Audio out (R) Audio out (L) If using a component signal CR/PR out CB/PB out Y out Audio out (R) Audio out (L) If using a SCART RGB input SCART RGB out SCART adapter Projector ViewSonic PJ1165...
• Make sure that you firmly connect the power cord to the projector and wall outlet. Connect the connector of the power cord to the AC inlet of the projector. Firmly plug the power cord’s plug into the outlet. Projector RGB OUT Projector AUDIO OUT AC Inlet Connector Outlet Plug ViewSonic PJ1165...
AA batteries according to their plus minus terminals (as indicated in the remote control). Close the battery cover. Replace the battery cover in the direction of the arrow and snap it back into place. ViewSonic PJ1165...
ID CHAGE switch. Slide the knob of the switch into the position of the ID number of the projector you want to control. approximately approximately 3 meters 3 meters ViewSonic PJ1165 ID CHANGE switch...
The projector would be enumerated memo as a mouse and a keyboard of HID (Human Interface Device) class devices, after connecting cable. Mouse left button Mouse move pointer Keyboard Arrow keys Mouse right button Keyboard (Front) ViewSonic PJ1165 (Rear)
Set the power switch to [O] (Off). The STANDBY/ON indicator will go off. Attach the lens cap. STANDBY/ON button / indicator STANDBY/ON button Power switch (On position) STANDBY/ON button / indicator STANDBY/ON button Power switch (Off position) ViewSonic PJ1165...
Select the signal you wish to project. Use the ZOOM buttons to adjust the screen size. Use the FOCUS buttons to adjust the focus. SEARCH button INPUT dial VIDEO button RGB button SEARCH button FOCUS ZOOM buttons buttons ViewSonic PJ1165...
This function is available only when the AUTO is selected memo to the item VIDEO of the INPUT menu. For a component video signal, the signal type is identified automatically independently of this function. ASPECT button AUTO button ViewSonic PJ1165...
Even if you don’t do anything, the dialog will memo automatically disappear after a few seconds. / / / to select the to correct the distortion. Cursor buttons POSITION button RESET button Cursor buttons KEYSTONE button ViewSonic PJ1165...
“BLANK” of the table of the section “SCREEN Menu”. Press the BLANK button again to remove the BLANK screen, and return to the input signal screen. to adjust the Cursor buttons VOLUME button MUTE button BLANK button ViewSonic PJ1165...
Press the VOLUME button again to close the dialog and complete this operation. Even if you don’t do anything, the dialog will memo automatically disappear after a few seconds. Large child window to select an audio PinP button Cursor buttons VOLUME button ViewSonic PJ1165...
RESET button button 3) Select the “SPEAKER” using the button, then press the ENTER button to operate the 4) Use the cursor button “TURN OFF”. button or 5) Press the MENU button again. button. button. to select the ViewSonic PJ1165...
The items of the MAIN menu are collectively returned to the initial setting. Note that the items “WHISPER” and “LANGUAGE” are not reset. Description Dark buttons.: Strong 16:9 16:9 16:9 SMALL WHISPER H:INVERT V:INVERT button to reset the MAIN menu CANCEL buttons.: Weak buttons.: buttons.: buttons.: H&V:INVERT buttons.: ViewSonic PJ1165...
COLOR TEMP using the Weak Weak Weak Soft Weak buttons.: (This table is continued to the following page.) buttons.: CUSTOM (or the ENTER) but- buttons.: Up buttons.: USER Weak buttons.: Strong Weak buttons.: Strong Weak buttons.: buttons.: buttons.: buttons.: buttons.: ViewSonic PJ1165...
Page 26
Note that the items “MY MEMORY” and “GAMMA” of the CUSTOM menu under the item “GAMMA” are not reset. Description (or the ENTER) button to perform the function.: button to reset the PICTURE-1 CANCEL buttons, and then ViewSonic PJ1165...
The items of the PICTURE-2 menu are collectively returned to the initial setting. Note that the item “H PHASE” is not reset. Description Down Right Left Small Small button to reset the PICTURE-2 CANCEL buttons.: buttons.: buttons.: buttons.: ViewSonic PJ1165...
When this adjustment is excessive, certain degradation may memo appear on the picture. Description SMPTE240 REC709 SCART RGB NTSC SECAM TURN OFF MIDDLE (This table is continued to the following page.) buttons.: REC601 buttons.: buttons.: NTSC4.43 M-PAL N-PAL buttons.: buttons.: ViewSonic PJ1165...
Page 29
The items of the INPUT menu are collectively returned to the initial setting. Note that the item “INFORMATION” is not reset. Description S-VIDEO buttons.: M1-D VIDEO (or the ENTER) button displays the INPUT TURN OFF button to reset the INPUT menu CANCEL buttons.: COMPONENT buttons.: ViewSonic PJ1165...
STANDBY/ON button. Please refer to the section “Turning Off The Power”. Description (or the ENTER) button performs the automatic buttons.: Short (min. 0 minute = DISABLE) TURN OFF (This table is continued to the following page.) buttons.: ViewSonic PJ1165...
Page 31
Select the EXECUTE using the items.: EXECUTE The items of the AUTO menu are collectively returned to the initial setting. Note that the item “ADJUST” is not reset. Description TURN OFF S-VIDEO COMPONENT button to reset the AUTO menu CANCEL buttons.: ViewSonic PJ1165...
Description ORIGINAL BLUE ORIGINAL TURN OFF (or the ENTER) button starts the MyScreen FULL TURN OFF Right Down (This table is continued to the following page.) buttons.: WHITE BLACK buttons.: buttons.: buttons.: buttons.: / / / ViewSonic PJ1165...
Page 33
If the picture registration failed, the message of the right is dis- played for a few seconds. Description TURN OFF CANCEL Press the button YES: Press the ENTER button buttons, and press the ENTER buttons.: button to reset the SCREEN menu NO: Press the ESC/RESET button ViewSonic PJ1165...
About caring for the air filter, please refer to the section “Air Filter”. memo Description buttons.: TURN OFF REAR (2) button to reset the timer.: CANCEL button to reset the timer.: CANCEL (This table is continued to the following page.) buttons.: button (1), then (Off) (On) ViewSonic PJ1165...
Page 35
About the optional lens ask your dealer. memo Select the ENABLE or the DISABLE using the buttons.: ENABLE DISABLE Selecting the ENABLE locks the adjustment of the lens shift, the zoom and the focus. button to reset the OPTION menu CANCEL LENS LOCK buttons.: ViewSonic PJ1165...
The items of the NETWORK menu are collectively returned to the initial setting. Description (or the ENTER) button calls buttons. (or the ENTER) button at the (or the ENTER) button at the TURN OFF (or the ENTER) button button to reset the NETWORK CANCEL ViewSonic PJ1165...
4) Make sure of the input data, then click "Write". These setting will be active after reboot. memo These setting will be stored, and used when DHCP is OFF. 5) Click “Return to top page”. 6) Click “REBOOT” to complete this operation. ViewSonic PJ1165...
Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage. HIGH HIGH VOLTAGE TEMPERATURE ViewSonic PJ1165 HIGH PRESSURE...
Incorrectly resetting of the lamp timer (resetting without replacement, or neglect of memo resetting after replacement) will result in incorrect message functions. Lamp cover knob Screws button, then press the button, then press and hold the RESET button. Lamp cover Tabs button ViewSonic PJ1165...
45 minutes for the lamp to cool sufficiently. • Use only the air filter of the specified type. Please call ViewSonic Tech Support for P/N. • Do not use the projector with the air filter and filter cover removed. The use without the air filter could result in damage.
Wipe lightly with gauze or a soft cloth. If soiling is severe, dip soft cloth in water or a neutral cleaner dilute in water, and memo wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth. ViewSonic PJ1165...
Please confirm the signal input connection, and the status of the signal source. The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit. Please confirm the specs for this unit or the signal source specs. ViewSonic PJ1165...
• Is the air filter dirty? • Does the peripheral temperature exceed 35°C? If the same indication is displayed after the treatment, please change the lamp by referring to the section “Lamp”. (This table is continued to the following page.) Description ViewSonic PJ1165...
Page 44
Please immediately turn the power off, and clean or change the air filter by referring to the section “Air Filter”. After cleaning or changing the air filter, please be sure to reset the filter time. After the treatment, resent the power to on. Description ViewSonic PJ1165...
The input changeover settings are mismatched. Select the input signal, and correct the settings. Cases not involving a machine defect (This table is continued to the following page.) Reference page(s) 35, 36 8, 9 ViewSonic PJ1165...
Page 46
The INPUT dial is set between the click points. Turn the INPUT dial and set it at a click point. changes with no operation. Cases not involving a machine defect Reference page(s) 8, 9 19, 32 4, 15 8, 9 35, 36 ViewSonic PJ1165...
(CR/PR, CB/PB, Y) AUDIO Input Ports AUDIO IN 1 AUDIO IN 2 AUDIO IN R/L PRJ-RLC-011 • Please call ViewSonic for the part number. • Please consult your dealer. Specification RGB output port RGB OUT Audio output port AUDIO OUT...
How long the warranty is effective: ViewSonic projectors are warranted for three (3) years for all parts excluding the lamp, three (3) years for all labor, and one (1) year for the lamp from the date of the first consumer purchase.
If you have any questions concerning which proper power cord to use, please consult with the dealer from whom you have purchased the product. Switzerland ...SEV Britain...BASE/BS Japan ...Electric Appliance Control Act Figure 1 Figure 2 Maximum Current Rating of Unit 10 Amps 12 Amps 12 Amps 10 Amps 12 Amps ViewSonic PJ1165...
The device complies with the requirements of the EEC directive 89/336/EEC as amended by 92/ 31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic compatibility,” and 73/23/EEC as amended by 93/68/EEC Art.13 with regard to “Safety.” User Information for all Countries NOTICE: Use the cables which are included with the projector or specified. ViewSonic PJ1165...