OSD Message ... 20 Indicator Message ... 21 Symptom... 22 Specifications... 23 Customer Support... 24 LIMITED WARRANTY VIEWSONIC Projector ... 25 Appendix Power Cord Safety Guidelines... 26 FCC Information ... 27 Compliance Information for Canada ... 27 Compliance Information for European Countries... 27 User Information for All Countries...
Image Optimization files are also available free of charge at our web site. Go to www.viewsonic.com and select “Support.” If you do not have access to the internet or if you require further assistance, contact "Customer Support" on page 24.
Power Cord Power Cord Power Cord (US) (UK) (Europe) Projector RGB Cable Component Video Cable Quick Start Guide Batteries CD-Wizard Mouse cable for Remote Control (PS/2) Device Remote Control Device Power Cord RCA Video/Audio Carrying Case (China) Cable ViewSonic PJ1065...
(air filter and intake for the cooling fan) Foot adjuster Terminal panel (see below) RGB IN 1 Terminal RGB IN 2 Terminal RGB OUT Terminal CONTROL Terminal AUDIO IN RGB1/DVI Terminal AUDIO IN RGB2/Terminal AUDIO OUT Terminal COMPONENT VIDEO Y Terminal Terminal Terminal ViewSonic PJ1065...
Page 6
• Be sure to protect the remote control device against humidity and do not put it on wet objects. • Do not leave the remote control device close to the cooling fan outlet of the projector. • Do not attempt to disassemble the remote control device. ViewSonic PJ1065 BLANK Button LASER Button...
• If the remote control device will not be used for an extended period of time, remove the batteries from its battery compartment. • Replace the batteries if the operation of the remote control device becomes irregular or NOTE: weak. ViewSonic PJ1065...
CAUTION • Do not release the foot adjuster button unless you hold the projector, or else the projector may overturn or the fingers may get caught. ViewSonic PJ1065 [inches (m)] Max. 1 (3) 2 (4)
• For the pin assignment of the connectors and the RS-232C communication data, refer to the service manual of PJ1065-2. • If you use the DVI terminal, the RGB OUT terminal may not work. Table 2: Cabling...
• This projector is recognized as a Plug & Play monitor. Use the standard display drivers. • Plug & Play may not function properly with the computer to be connected. Use the RGB IN 2 terminal if Plug & Play does not function correctly. ViewSonic PJ1065 DVD Player Computer (desktop)
• If the projector continues projecting the same image, the image may remain as an after-image. Do not project the same image for a long time. STANDBY/ON Button ZOOM button Lens cap STANDBY/ ON Button FOCUS button ZOOM button ViewSonic PJ1065...
• Use the remote control device at a distance of approximately 5 m from the sensor on the NOTE: front of the projector, and within a range of 30 °left-right. Strong light and obstacles will interfere with the operation of the remote control device. ViewSonic PJ1065 Table 3: Basic Operation Description COMPONENT VIDEO (...
Page 13
Select KEYSTONE Mode: Press the Vertical Adjust KEYSTONE: Press the Table 3: Basic Operation (continued) Description (MENU SELECT) P.IN P. off ( Small) Horizontal button. button. buttons as with Single menu button. button. button. button in the KEYSTONE mode. ViewSonic PJ1065...
Center • 4:3 small cannot be selected with the input of 720P or 1080i component. • 4:3 small may not be displayed correctly with some input signals. ViewSonic PJ1065 RGB IN 1 RGB IN 2 Table 4: Setup Menu Description...
Select HDTV mode: Select the 1035i mode or 1080i mode suitable for the input HDTV (**) signal with the buttons, and start or stop operation Table 5: Input Menu Description button. When the TURN ON is selected, the black enhancement button. button. buttons. ViewSonic PJ1065...
• Valid only at RGB IN 1, RGB IN 2 or DVI input. P. IN P. Select signal of P. in P. Display: Press the INPUT VIDEO Select Gamma Mode: Select the gamma mode with the GAMMA NORMAL ViewSonic PJ1065 buttons, and start buttons. Table 6: Image Menu Description S-VIDEO COMPONENT CINEMA DYNAMIC button.
Table 7: Options Menu Description Increase VOLUME button. button. button. button. When WHISPER is buttons. buttons. buttons. The system button. When STOP is button. button. ViewSonic PJ1065...
Set / Clear WHISPER Mode: Press the WHISPER selected, the WHISPER mode is active. In the WHISPER mode, acoustic noise level from the unit is reduced, and brightness level on screen is a little lower. ViewSonic PJ1065 Table 8: No Signal Menu Description Increase VOLUME or VOLUME button.
• The LAMP indicator is also red when the lamp unit reaches high temperature. Before NOTE: replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp. HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE Lamp Reflector Front glass ViewSonic PJ1065...
• Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when NOTE: replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly. ViewSonic PJ1065 0 ■ CANCEL’ message will...
• Do not use detergents or chemicals other than those noted above (e.g. benzene or thinners). • Do not use cleaning sprays. • Do not rub with hard materials, or tap the equipment. filter cover filters ViewSonic PJ1065...
(*2) The unit has a function to turn the power off which will be active when the usage time reaches 2000 hr. However the life of lamp might be much different, so that it might happen that a lamp is cut off before the function is active. ViewSonic PJ1065 Table 9: OSD Message Contents The usage time of lamp will be reaching 2000 hr shortly (*2).
Switch power OFF, and wait for 20 minutes until the equipment cools. Check whether the ventilation openings are blocked, whether the air filter is dirty, or whether the ambient temperature exceeds 35 °C. Then switch power ON again. Contact your dealer if the same problem occurs again. ViewSonic PJ1065...
The lamp is approaching the end of its service life. Focus or H PHASE is out Video is blurred. of adjustment. ViewSonic PJ1065 Table 11: Symptom Possible cause Turn on the main power switch. Plug the power cord into an AC power outlet.
United Kingdom Europe, Middle East, Baltic countries, and North Africa Australia and New Zealand Singapore/India and Southeast Asia Other Asia/Pacific countries South Africa ViewSonic PJ1065 Web site T = Telephone F = FAX viewsonic.com/support T: (800) 688-6688 F: (909) 468-1202 viewsonic.com/support...
How long the warranty is effective: ViewSonic projectors are warranted for two (2) years for all parts excluding the lamp, two (2) years for all labor, and ninety (90) days for the lamp from the date of the first consumer purchase.
HAR-Certified, and a special mark that will appear on the outer sheath, or on the insulation of one of the inner conductors. If you have any questions concerning which proper power cord to use, please consult with the dealer from whom you have purchased the product. ViewSonic PJ1065 Switzerland ...SEV Britain...BASE/BS Japan ...Electric Appliance Control Act...
The device complies with the requirements of the EEC directive 89/336/EEC as amended by 92/ 31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic compatibility,” and 73/23/EEC as amended by 93/68/EEC Art.13 with regard to “Safety.” User Information for All Countries NOTICE: Use the cables which are included with the projector or specified. ViewSonic PJ1065...