AL-KO T15-102 Translation Of Original User Instructions page 29

Assembling the grass box
Place the lower part of the frame on a suitable base (e.g. a
19
table) and push both the struts (6 mm Ø) into the bores.
Position the upper part of the frame, inserting both the struts
21
into the bores on the upper part of the frame provided for
this purpose.
Screw the upper part of the frame onto the lower part of the
20
frame on both sides.
M 6 x 35 hexagonal head screw
Ø 6 x Ø 18 shim
Ø 6 x Ø 12 shim
selbstsichernde Mutter M 6
Attention!
Only tighten the nuts by hand to start with due to the
subsequent fixing of the box fabric.
Fit disk Ø 6 x Ø 18 under the screw head!
Screw the transverse tube
21
M 6 x 45 hexagonal head screw
Ø 6 x Ø 12 shim
Ø 6 curved shim
M 6 self-locking nut
Place the frame onto the box base of the fabric sack.
22
Attention!
The ribs of the box base pointing upwards.
Clip the fabric sack onto the box frame.
Remove the upper frame screw connection and screw the
23
fitting flap of the fabric sack together with the upper and
lower part of the box frame.
Fit the Ø 6 x Ø 18 shim under the screw head.
Carry out this procedure on both sides.
Screw the box handle
24
"superstructure right"
M 8 x 60 screw
Ø 8 x Ø 15 shim
shim
Attention!
The connection contours of the two superstructures
must correspond with the outer contour of the box lid.
(4 x)
(4 x)
(4 x)
(4 x)
onto the box frame.
(2 x)
(4 x)
(2 x)
(2 x)
onto "superstructure left"
.
(2 x)
(2 x)
(2 x)
GB
Screw the box handle onto the box lid
25
M 6 x 20 screw
Ø 6 x Ø 12 shim
Ø 6 x Ø 18 shim
M 6 self-locking nut
Position the box lid and screw onto the box frame
26
M 6 x 40 hexagonal head screw
Ø 6 x Ø 18 shim
Ø 6 x Ø 12 shim
27
M 6 self-locking nut
Holder
Attention!
Fit the Ø 6 x 18 shim under the screw head.
Push the box strut (Ø 8 mm) through the base of the box
and the lower part of the frame.
Attention!
The box strut must protrude by the same distance on
both sides of the box.
Thread the gas spring onto the box strut in the order shown
28
and screw tight. Carry out this procedure on both sides.
Ø 12 x 13 spacer bushing
Gas-pressure spring
Ø 8 x Ø 15 shim
M 8 self-locking cap nut
Attention!
Only tighten the cap nuts to such an extent that the gas-
pressure springs can still be pivoted.
Assembling the grass box on the tractor
Hold the grass box by the box handle in one hand. With the
29
other hand - gently pressing onto the box lid - position the
upper part of the frame onto the box holding arms and push
forwards until the grass box engages in the bearings.
Attention!
The arrows on the box lid and the seat console must
match.
and
If the gap between the box lid and the seat console is too
30
large, the box holding arms can be adjusted by loosening
the screws in the directions shown.
Push the forkhead
31
fitting lug
Push the securing bolts
and lock them.
Carry out this procedure on both sides.
GB 13
of the gas-pressure spring across the
of the back wall until the bores are flush.
through the forkhead and the lug
(2 x)
(2 x)
(2 x)
(2 x)
(5 x)
(5 x)
(5 x)
(5 x)
(2 x)
(2 x)
(2 x)
(2 x)
(2 x)