Microatx motherboard with lga1150 intel core i7/i5/i3, pentium or celeron cpu, intel h81 chipset, dual gbe, ddr3, internal displayport, vga, usb 3.0, com ports four sata 6 gb/s ports, ipmi 2.0 and rohs
Micro atx motherboard s upports lga1155 intel core i7/i5/i3/pentium/celeron cpu per intel h61, ddr3, dual vga,
dual realtek pcie gbe, usb 2.0, com, sata 3gb/s , hd audio and rohs (199 pages)
Micro atx motherboard supports lga1155 intel core
i7/i5/i3/pentium/celeron cpu per intel h61, ddr3, vga/dvi-d, dual realtek pcie gbe, usb 2.0, com, sata 3gb/s ,
hd audio and rohs (192 pages)
Micro atx motherboard supports 22nm lga1155 intel core i7/i5/i3 cpu with intel q77, ddr3, three independent dis plays via dual hdmi/dvi-i, dual intel pcie gbe, usb 3.0, sata 6gb/s , ten serial ports , hd audio and rohs (212 pages)
Summary of Contents for IEI Technology IMB-H810-i2-R11
Page 1
IMB-H810-i2 microATX Motherboard MODEL: IMB-H810-i2 microATX Motherboard with LGA1150 Intel® Core i7/i5/i3, Pentium® or Celeron® CPU, Intel® H81 Chipset, Dual GbE, DDR3, Internal DisplayPort, VGA, USB 3.0, COM Ports Four SATA 6Gb/s Ports, IPMI 2.0 and RoHS User Manual Page i Rev.
Page 2
IMB-H810-i2 microATX Motherboard Revision Date Version Changes September 8, 2015 1.11 Updated I/O shielding part number June 16, 2015 1.10 Updated for R11 version March 13, 2014 1.01 Deleted I C information January 13, 2014 1.00 Initial release Page ii...
Page 3
IMB-H810-i2 microATX Motherboard Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Page 4
IMB-H810-i2 microATX Motherboard Manual Conventions WARNING Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. CAUTION Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product. NOTE These messages inform the reader of essential but non-critical information.
IMB-H810-i2 microATX Motherboard Table of Contents 1 INTRODUCTION......................1 1.1 I ......................2 NTRODUCTION 1.2 B ........................3 ENEFITS 1.3 F ........................3 EATURES 1.4 C ......................4 ONNECTORS 1.5 D ....................... 5 IMENSIONS 1.6 D ........................ 6 1.7 T ..................
Page 6
IMB-H810-i2 microATX Motherboard 3.2.11 LAN LED Connectors..................29 3.2.12 Memory Card Slots ..................30 3.2.13 Parallel Port Connector ................30 3.2.14 PCI Express Power Connector ..............32 3.2.15 Power Button ....................32 3.2.16 SATA 6Gb/s Drive Connectors............... 33 3.2.17 Serial Port Connector (COM3~COM6), RS-232........... 34 3.2.18 Serial Port Connector (COM7~COM10), RS-232.........
Page 7
IMB-H810-i2 microATX Motherboard 4.3.6 USB Power Select .................... 63 4.4 I ............64 NTERNAL ERIPHERAL EVICE ONNECTIONS 4.4.1 SATA Drive Connection ................... 64 4.5 IPMI S ..................65 ETUP ROCEDURE 4.5.1 Managed System Hardware Setup ..............65 4.5.2 Using the IEI iMAN Web GUI................66 5 BIOS ..........................
Page 8
IMB-H810-i2 microATX Motherboard 5.4.2 System Agent (SA) Configuration ..............106 5.4.2.1 Graphics Configuration................107 5.4.2.2 NB PCIe Configuration................110 5.4.2.3 Memory Configuration ................111 5.5 B ........................112 5.6 S ........................114 ECURITY 5.7 S & E ......................114 5.8 S ...................116 ERVER ANAGEMENT 5.8.1 System Event Log ....................117 5.8.2 BMC Network Configuration................119 6 SOFTWARE DRIVERS ....................
Page 9
IMB-H810-i2 microATX Motherboard List of Figures Figure 1-1: IMB-H810-i2........................2 Figure 1-2: Connectors ........................4 Figure 1-3: IMB-H810-i2 Dimensions (mm) ..................5 Figure 1-4: Data Flow Diagram......................6 Figure 3-1: Connectors and Jumpers..................16 Figure 3-2: Audio Connector Location ..................19 Figure 3-3: ATX Power Connector Location ................20 Figure 3-4: Battery Connector Location..................21 Figure 3-5: Chassis Intrusion Connector Location..............22 Figure 3-6: CPU Power Connector Location................23...
Page 10
IMB-H810-i2 microATX Motherboard Figure 3-27: Audio Connector .....................44 Figure 3-28: PS/2 Pinouts ......................45 Figure 3-29: Ethernet Connector....................46 Figure 3-30: Serial Port Connector Pinouts................48 Figure 3-31: VGA Connector .......................49 Figure 4-1: Disengage the CPU Socket Load Lever..............53 Figure 4-2: Remove Protective Cover..................54 Figure 4-3: Insert the Socket LGA1150 CPU................55 Figure 4-4: Close the Socket LGA1150 ..................56 Figure 4-5: Cooling Kits (CF-1156A-RS and CF-1156E-RS) .............56...
Page 13
IMB-H810-i2 microATX Motherboard Table 3-28: LAN2 Pinouts ......................46 Table 3-29: Connector LEDs......................46 Table 3-30: USB 3.0 Port Pinouts....................47 Table 3-31: LAN1 Pinouts ......................47 Table 3-32: COM1 Serial Port Connector Pinouts ..............48 Table 3-33: COM2 Serial Port Connector Pinouts ..............48 Table 3-34: VGA Connector Pinouts...................49 Table 4-1: COM 10 Function Select Jumper Settings ...............61 Table 4-2: Flash Descriptor Security Override Jumper Settings..........62 Table 4-3: PCIe x16 Interface Setup....................63...
Page 14
IMB-H810-i2 microATX Motherboard BIOS Menus BIOS Menu 1: Main ........................71 BIOS Menu 2: Advanced ......................73 BIOS Menu 3: ACPI Configuration ....................73 BIOS Menu 4: RTC Wake Settings ....................75 BIOS Menu 5: Trusted Computing ....................76 BIOS Menu 6: CPU Information....................77 BIOS Menu 7: SATA Configuration .....................80 BIOS Menu 8: USB Configuration ....................81 BIOS Menu 9: F81866 Super IO Configuration ................82 BIOS Menu 10: Serial Port n Configuration Menu..............83...
Page 15
IMB-H810-i2 microATX Motherboard BIOS Menu 31: System Event Log ................... 117 BIOS Menu 32: BMC Network Configuration ................119 Page xv...
IMB-H810-i2 microATX Motherboard 1.1 Introduction Figure 1-1: IMB-H810-i2 The IMB-H810-i2 is a microATX motherboard. It accepts a Socket LGA1150 Intel® Core™ i7, Core™ i5, Core™ i3, Pentium® or Celeron® processor and supports two 240-pin 1333/1066 MHz dual-channel DDR3 DIMM modules up to 16.0 GB maximum. The IMB-H810-i2 features Intelligent Platform Management Interface (IPMI) that helps lower the overall costs of server management by enabling users to maximize IT resource, save time and manage multiple systems.
IMB-H810-i2 microATX Motherboard 1.2 Benefits Some of the IMB-H810-i2 motherboard benefits include: Powerful graphics with multiple monitors Staying connected with both wired LAN connections Speedy running of multiple programs and applications 1.3 Features Some of the IMB-H810-i2 motherboard features are listed below: ...
IMB-H810-i2 microATX Motherboard 1.5 Dimensions The main dimensions of the IMB-H810-i2 are shown in the diagram below. Figure 1-3: IMB-H810-i2 Dimensions (mm) Page 5...
IMB-H810-i2 microATX Motherboard 1.6 Data Flow F igure 1-4 shows the data flow between the system chipset, the CPU and other components installed on the motherboard. Figure 1-4: Data Flow Diagram Page 6...
IMB-H810-i2 microATX Motherboard Specification/Model IMB-H810-i2 Three external audio jacks (line-in, line-out, mic-in) Audio Connectors One audio connector (10-pin header) Ethernet Two RJ-45 GbE ports IPMI 2.0 Supported by the optional iRIS-2400 module Keyboard/Mouse One PS/2 keyboard connector One PS/2 mouse connector One TPM connector via 20-pin header Serial Ports Two external RS-232 serial port...
IMB-H810-i2 microATX Motherboard 2.1 Anti-static Precautions WARNING! Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user. Make sure to adhere to the following guidelines: Wear an anti-static wristband: Wearing an anti-static wristband can prevent electrostatic discharge.
IMB-H810-i2 microATX Motherboard 2.3 Packing List NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the IMB-H810-i2 was purchased from or contact sales representative directly by sending an email to ales@ieiworld.com.
IMB-H810-i2 microATX Motherboard Quantity Item and Part Number Image Quick Installation Guide Table 2-1: Packing List 2.4 Optional Items The following are optional components which may be separately purchased: Item and Part Number Image IPMI 2.0 adapter card with AST2400 BMC chip (P/N: iRIS-2400-R10) Dual-port USB cable with bracket (P/N: 19800-003100-200-RS)
Page 29
IMB-H810-i2 microATX Motherboard Item and Part Number Image Parallel port cable (P/N:19800-000049-RS) LGA1155/LGA1156 cooler kit (1U chassis compatible, 73W) (P/N: CF-1156A-RS-R11) LGA1155/LGA1156 cooler kit (95W) (P/N: CF-1156E-R11) DisplayPort to HDMI converter board for IEI IDP connector (P/N: DP-HDMI-R10) DisplayPort to 24-bit dual-channel LVDS converter board for iEi IDP connector (P/N: DP-LVDS-R10) DisplayPort to VGA converter board for iEi IDP connector...
IMB-H810-i2 microATX Motherboard 3.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 3.1.1 IMB-H810-i2 Layout The figures below show all the connectors and jumpers. Figure 3-1: Connectors and Jumpers Page 16...
IMB-H810-i2 microATX Motherboard 3.2.3 Battery Connector CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. CN Label: BAT1 CN Type: 2-pin wafer, p=2.0 mm CN Location: See Figure 3-4...
IMB-H810-i2 microATX Motherboard 3.2.4 Chassis Intrusion Connector CN Label: CHASSIE1 2-pin header, p=2.54 mm CN Type: CN Location: F igure 3-5 CN Pinouts: T able 3-6 The chassis intrusion connector is for a chassis intrusion detection sensor or switch that detects if a chassis component is removed or replaced.
IMB-H810-i2 microATX Motherboard 3.2.5 CPU Power Connector CN Label: CPU12V1 4-pin connector, p=4.2 mm CN Type: CN Location: See Figure 3-6 CN Pinouts: See Table 3-7 The CPU power input connector provides power to the CPU. Figure 3-6: CPU Power Connector Location PIN NO.
IMB-H810-i2 microATX Motherboard 3.2.7 Fan Connector (CPU) CN Label: CPU_FAN1 4-pin wafer, p=2.54 mm CN Type: CN Location: See Figure 3-8 CN Pinouts: See Table 3-9 The fan connector attaches to a CPU cooling fan. Figure 3-8: CPU Fan Connector Location PIN NO.
IMB-H810-i2 microATX Motherboard 3.2.8 Fan Connector (System) CN Label: SYS_FAN1 CN Type: 3-pin wafer, p=2.54 mm CN Location: See Figure 3-9 See Table 3-10 CN Pinouts: Each fan connector attaches to a system cooling fan. Figure 3-9: System Fan Connector Location PIN NO.
IMB-H810-i2 microATX Motherboard 3.2.9 Front Panel Connector CN Label: F_PANEL1 CN Type: 14-pin header, p=2.54 mm CN Location: See Figure 3-10 See Table 3-11 CN Pinouts: The front panel connector connects to the indicator LEDs and buttons on the computer's front panel.
IMB-H810-i2 microATX Motherboard 3.2.10 iRIS Module Slot CN Label: IPMI1 204-pin DDR3 SO-DIMM slot CN Type: CN Location: F igure 3-11 The iRIS module slot is used to install the IEI iRIS-2400 IPMI 2.0 module. WARNING: The iRIS module slot is designed to install the IEI iRIS-2400 IPMI 2.0 module only.
IMB-H810-i2 microATX Motherboard 3.2.11 LAN LED Connectors CN Label: LED_LAN1, LED_LAN2 2-pin header, p=2.54 mm CN Type: CN Location: F igure 3-12 CN Pinouts: T able 3-12 and Table 3-13 The LAN LED connectors are used to connect to the LAN LED indicators on the chassis to indicate users the link activities of the two LAN ports.
IMB-H810-i2 microATX Motherboard Figure 3-14: Parallel Port Connector Location Description Description STROBE# DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 ACKNOWLEDGE# BUSY PAPER EMPTY PRINTER SELECT AUTO FORM FEED # ERROR# INITIALIZE# PRINTER SELECT LN# GROUND GROUND...
IMB-H810-i2 microATX Motherboard 3.2.14 PCI Express Power Connector CN Label: ATXPWR1 4-pin connector, p=5.08 mm CN Type: CN Location: See Figure 3-15 CN Pinouts: See Table 3-15 The PCIe power connector provides extra power to the PCIe expansion card. Figure 3-15: PCIe Power Location Description +12V Table 3-15: PCIe Power Pinouts...
IMB-H810-i2 microATX Motherboard Figure 3-16: Power Button Location 3.2.16 SATA 6Gb/s Drive Connectors CN Label: S_ATA1, S_ATA2, S_ATA3, S_ATA4 CN Type: 7-pin SATA drive connectors CN Location: See Figure 3-17 See Table 3-16 CN Pinouts: The SATA drive connectors can be connected to SATA drives. Figure 3-17: SATA 6Gb/s Drive Connector Locations Page 33...
IMB-H810-i2 microATX Motherboard PIN NO. DESCRIPTION PIN NO. DESCRIPTION Table 3-18: COM7~10 Serial Port Connector Pinouts 3.2.19 Serial Port Connector (COM10), RS-422/485 CN Label: CN10 4-pin wafer, p=2.0 mm CN Type: CN Location: See Figure 3-20 CN Pinouts: See Table 3-19 Used for RS-422/485 communications.
IMB-H810-i2 microATX Motherboard Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the DB-9 connector are listed below. RS-422 Pinouts RS-485 Pinouts Table 3-20: DB-9 RS-422/485 Pinouts 3.2.20 SMBus Connector CN Label: CN Type: 4-pin wafer, p=1.25 mm CN Location: See Figure 3-21 CN Pinouts:...
IMB-H810-i2 microATX Motherboard 3.2.24 USB 2.0 Connectors CN Label: USB3, USB4, USB5, USB6 8-pin header, p=2.54 mm CN Type: CN Location: See Figure 3-25 CN Pinouts: See Table 3-25 The USB 2.0 connectors connect to USB 2.0 devices. Each pin header provides two USB 2.0 ports.
IMB-H810-i2 microATX Motherboard Figure 3-27: Audio Connector 3.3.2 Keyboard and Mouse Connectors CN Label: KBMS1 CN Type: PS/2 CN Location: See Figure 3-26 CN Pinouts: See Figure 3-28 and Table 3-26 The PS/2 ports are for connecting a PS/2 mouse and a PS/2 keyboard. Description Description Keyboard Data...
IMB-H810-i2 microATX Motherboard Figure 3-28: PS/2 Pinouts 3.3.3 Ethernet and USB 2.0 Connectors CN Label: LAN2_USB2 CN Type: RJ-45, USB 3.0 CN Location: See Figure 3-26 CN Pinouts: See Table 3-27 and Table 3-28 The USB 2.0 connector can be connected to a USB device. DESCRIPTION DESCRIPTION USB_DATA-...
IMB-H810-i2 microATX Motherboard DESCRIPTION DESCRIPTION USB_DATA+ USB_ DATA+ USB3_RX- USB3_RX- USB3_RX+ USB3_ RX+ USB3_TX- USB3_TX- USB3_TX+ USB3_TX+ Table 3-30: USB 3.0 Port Pinouts A 10/100/1000 Mb/s connection can be made to a Local Area Network. DESCRIPTION DESCRIPTION LAN1_MDI0P LAN1_MDI2P LAN1_MDI0N LAN1_MDI2N LAN1_MDI1P LAN1_MDI3P...
IMB-H810-i2 microATX Motherboard 4.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the IMB-H810-i2 may result in permanent damage to the IMB-H810-i2 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the IMB-H810-i2.
Page 68
IMB-H810-i2 microATX Motherboard WARNING: The installation instructions described in this manual should be carefully followed in order to prevent damage to the components and injury to the user. Before and during the installation please DO the following: Read the user manual: The user manual provides a complete description of the IMB-H810-i2 installation instructions and configuration options.
IMB-H810-i2 microATX Motherboard 4.2.1 Socket LGA1150 CPU Installation WARNING: CPUs are expensive and sensitive components. When installing the CPU please be careful not to damage it in anyway. Make sure the CPU is installed properly and ensure the correct cooling kit is properly installed.
IMB-H810-i2 microATX Motherboard Figure 4-2: Remove Protective Cover Step 3: Inspect the CPU socket. Make sure there are no bent pins and make sure the socket contacts are free of foreign material. If any debris is found, remove it with compressed air.
IMB-H810-i2 microATX Motherboard Step 6: Align the CPU pins. Locate pin 1 and the two orientation notches on the CPU. Carefully match the two orientation notches on the CPU with the socket alignment keys. Step 7: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are properly aligned, the CPU should slide into the CPU socket smoothly.
IMB-H810-i2 microATX Motherboard Figure 4-4: Close the Socket LGA1150 Step 9: Connect the 12 V power to the board. Connect the 12 V power from the power supply to the board. Step 0: 4.2.2 Socket LGA1150 Cooling Kit Installation WARNING: DO NOT attempt to install a push-pin cooling fan.
IMB-H810-i2 microATX Motherboard WARNING: Do not wipe off (accidentally or otherwise) the pre-sprayed layer of thermal paste on the bottom of the heat sink. The thermal paste between the CPU and the heat sink is important for optimum heat dissipation. To install the cooling kit, follow the instructions below.
IMB-H810-i2 microATX Motherboard Step 4: Secure the cooling kit by fastening the four retention screws of the cooling kit. Step 5: Connect the fan cable. Connect the cooling kit fan cable to the fan connector on the IMB-H810-i2. Carefully route the cable and avoid heat generating chips and fan blades.
IMB-H810-i2 microATX Motherboard 4.2.4 iRIS-2400 Module Installation WARNING: The iRIS module slot is designed to install the IEI iRIS-2400 IPMI 2.0 module only. DO NOT install other modules into the iRIS module slot. Doing so may cause damage to the IMB-H810-i2. To install the iRIS-2400 module, please follow the steps below and refer to Figure 4-8.
IMB-H810-i2 microATX Motherboard Step 5: Removing the iRIS-2400 module. To remove the iRIS-2400 module, push both handles outward. The module is ejected by a mechanism in the socket.Step 0: NOTE: After installing the iRIS-2400 module, use LAN2 port to establish a network connection.
IMB-H810-i2 microATX Motherboard 4.3.2 Clear CMOS Button To reset the BIOS, remove the on-board battery and press the clear CMOS button for three seconds or more. The clear CMOS button location is shown in Figure 4-10. Figure 4-10: Clear CMOS Button Location 4.3.3 COM 10 Function Select The COM 10 Function Select jumper sets the communication protocol used by the COM 10 port as RS-232, RS-422 or RS-485.
IMB-H810-i2 microATX Motherboard 4.3.5 PCIe x16 Interface Setup The PCIe x16 interface setup is made through the BIOS options in “Chipset PCH-IO Configuration” BIOS menu. Use the PCIEX16 Power option to configure the PCIe x16 channel mode. BIOS Options Description 1 x16 PCIE Sets the PCIe x16 slot as one PCIe x16.
IMB-H810-i2 microATX Motherboard 4.4 Internal Peripheral Device Connections This section outlines the installation of peripheral devices to the onboard connectors. 4.4.1 SATA Drive Connection The IMB-H810-i2 is shipped with two SATA drive cables. To connect the SATA drives to the connectors, please follow the steps below. Step 1: Locate the connectors.
IMB-H810-i2 microATX Motherboard Figure 4-14: SATA Power Drive Connection Step 5: The SATA power cable can be bought from IEI. See Optional Items in Section 2.4. 4.5 IPMI Setup Procedure The IMB-H810-i2 features Intelligent Platform Management Interface (IPMI) that helps lower the overall costs of server management by enabling users to maximize IT resources, save time and manage multiple systems.
IMB-H810-i2 microATX Motherboard Step 2: Make sure at least one DDR3 DIMM is installed in one of the DIMM sockets. If multiple DIMMs are installed, all of the DIMMs must be same size, same speed and same brand to get the best performance. Step 3: Connect an Ethernet cable to the RJ-45 connector labeled LAN2_USB2 (Figure 3-26).
IMB-H810-i2 microATX Motherboard -Username: admin -Password: admin Step 5: Press the login button to login the system. Step 6: The IEI iMAN Web GUI appears (Figure 4-16). Figure 4-16: IEI iMAN Web GUI NOTE: To understand how to use the IEI iMAN Web GUI, please refer to the iRIS-2400 Web GUI user manual in the utility CD came with the IMB-H810-i2.
IMB-H810-i2 microATX Motherboard 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.
IMB-H810-i2 microATX Motherboard Function Decrease the numeric value or make changes Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu...
IMB-H810-i2 microATX Motherboard 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset...
IMB-H810-i2 microATX Motherboard The System Overview field has two user configurable fields: System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.
IMB-H810-i2 microATX Motherboard Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Server Mgmt > ACPI Settings System ACPI Parameters > RTC Wake Settings > Trusted Computing > CPU Configuration > SATA Configuration ---------------------- >...
Page 90
IMB-H810-i2 microATX Motherboard ACPI Sleep State [S1 (CPU Stop Clock)] Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used. Suspend Disabled The system enters S1(POS) sleep state. The (CPU Stop EFAULT...
IMB-H810-i2 microATX Motherboard 5.3.2 RTC Wake Settings The RTC Wake Settings menu (BIOS Menu 4) configures RTC wake event. The RTC wake function is supported in ACPI (S3/S4/S5) and APM soft off modes. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced Wake System with Fixed Time [Disabled]...
IMB-H810-i2 microATX Motherboard Enabled If selected, the following appears with values that can be selected: *Wake up every day *Wake up date *Wake up hour *Wake up minute *Wake up second After setting the alarm, the computer turns itself on from a suspend state when the alarm goes off.
IMB-H810-i2 microATX Motherboard Security Device Support [Disable] Use the Security Device Support option to configure support for security devices. Security Device support is disabled. Disable EFAULT Enable Security Device support is enabled. 5.3.4 CPU Information Use the CPU Information submenu (BIOS Menu 6) to view detailed CPU specifications and configure the CPU.
Page 94
IMB-H810-i2 microATX Motherboard The CPU Configuration menu (BIOS Menu 6) lists the following CPU details: Processor Type: Lists the brand name of the CPU being used CPU Signature: Lists the CPU signature value. Microcode Patch: Lists the microcode patch being used. ...
Page 95
IMB-H810-i2 microATX Motherboard Intel Virtualization Technology [Disabled] Use the Intel Virtualization Technology option to enable or disable virtualization on the system. When combined with third party software, Intel® Virtualization technology allows several OSs to run on the same system at the same time. ...
IMB-H810-i2 microATX Motherboard 5.3.5 SATA Configuration Use the SATA Configuration menu (BIOS Menu 7) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced SATA Controller(s) [Enabled] Enable or disable SATA SATA Mode Selection...
IMB-H810-i2 microATX Motherboard 5.3.6 USB Configuration Use the USB Configuration menu (BIOS Menu 8) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced USB Configuration Enables Legacy USB support.
IMB-H810-i2 microATX Motherboard Disabled Legacy USB support disabled Legacy USB support disabled if no USB devices are Auto connected 5.3.7 F81866 Super IO Configuration Use the F81866 Super IO Configuration menu (BIOS Menu 9) to set or change the configurations for the parallel ports and serial ports.
IMB-H810-i2 microATX Motherboard 5.3.7.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 10) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced Serial Port n Configuration Enable or Disable Serial Port (COM) Serial Port [Enabled]...
Page 100
IMB-H810-i2 microATX Motherboard IO=3F8h; Serial Port I/O port address is 3F8h and the interrupt IRQ=3, 4 address is IRQ3,4 Serial Port I/O port address is 2C0h and the interrupt IO=2C0h; address is IRQ3, 4 IRQ=3, 4 IO=2C8h; Serial Port I/O port address is 2C8h and the interrupt IRQ=3, 4 address is IRQ3, 4...
Page 101
IMB-H810-i2 microATX Motherboard 5.3.7.1.3 Serial Port 3 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disabled Disable the serial port Enable the serial port Enabled EFAULT Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
Page 102
IMB-H810-i2 microATX Motherboard Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address. Auto The serial port IO port address and interrupt address EFAULT are automatically detected. Serial Port I/O port address is 2E8h and the interrupt IO=2E8h;...
Page 103
IMB-H810-i2 microATX Motherboard IO=2C0h; Serial Port I/O port address is 2C0h and the interrupt IRQ=10, 11 address is IRQ10, 11 Serial Port I/O port address is 2C8h and the interrupt IO=2C8h; address is IRQ10, 11 IRQ=10, 11 IO=2D0h;...
IMB-H810-i2 microATX Motherboard IO=2D0h; Serial Port I/O port address is 2D0h and the interrupt IRQ=10, 11 address is IRQ10, 11 Serial Port I/O port address is 2D8h and the interrupt IO=2D8h; address is IRQ10, 11 IRQ=10, 11 IO=2E0h;...
Page 105
IMB-H810-i2 microATX Motherboard Change Settings [Auto] Use the Change Settings option to change the parallel port IO port address and interrupt address. Auto The parallel port IO port address and interrupt EFAULT address are automatically detected. Parallel Port I/O port address is 378h and the IO=378h;...
IMB-H810-i2 microATX Motherboard 5.3.8 F81866 H/W Monitor The F81866 H/W Monitor menu (BIOS Menu 12) contains the fan configuration submenus and displays operating temperature, fan speeds and system voltages. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced PC Health Status Smart FAN Configuration >...
IMB-H810-i2 microATX Motherboard +5VSB +3.3V +3.3VSB 5.3.8.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 13) to configure smart fan temperature and speed settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced Smart Fan Mode Configuration Smart Fan Mode Select CPU_FAN1 Smart Fan Control...
IMB-H810-i2 microATX Motherboard Fan start/off temperature Use the + or – key to change the Fan start/off temperature value. Enter a decimal number between 1 and 100. Fan start PWM Use the + or – key to change the Fan start PWM value. Enter a decimal number between 1 and 128.
IMB-H810-i2 microATX Motherboard 5.3.9.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 10) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced Serial Port n Configuration Enable or Disable Serial Port (COM) Serial Port [Enabled]...
Page 110
IMB-H810-i2 microATX Motherboard IO=260h; Serial Port I/O port address is 260h and the interrupt IRQ=10, 11 address is IRQ10, 11 Serial Port I/O port address is 268h and the interrupt IO=268h; address is IRQ10, 11 IRQ=10, 11 IO=270h;...
Page 111
IMB-H810-i2 microATX Motherboard IO=278h; Serial Port I/O port address is 278h and the interrupt IRQ=10, 11 address is IRQ10, 11 5.3.9.1.3 Serial Port 9 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. ...
Page 112
IMB-H810-i2 microATX Motherboard 5.3.9.1.4 Serial Port 10 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disabled Disable the serial port Enable the serial port Enabled EFAULT Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
IMB-H810-i2 microATX Motherboard 5.3.10 Serial Port Console Redirection The Serial Port Console Redirection menu (BIOS Menu 16) allows the console redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port. Aptio Setup Utility –...
Page 114
IMB-H810-i2 microATX Motherboard Console Redirection [Disabled] Use Console Redirection option to enable or disable the console redirection function. Disabled the console redirection function Disabled EFAULT Enabled Enabled the console redirection function The following options are available in the Console Redirection Settings submenu when the Console Redirection option is enabled.
Page 115
IMB-H810-i2 microATX Motherboard Parity [None] Use the Parity option to specify the parity bit that can be sent with the data bits for detecting the transmission errors. None No parity bit is sent with the data bits. EFAULT ...
IMB-H810-i2 microATX Motherboard 5.3.11 iEi Feature Use the iEi Feature menu (BIOS Menu 17) to configure IEI One Key Recovery function. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function Reboot and recover Auto Recovery Function [Disabled] system automatically...
IMB-H810-i2 microATX Motherboard 5.4 Chipset Use the Chipset menu (BIOS Menu 18) to access the PCH-IO and System Agent (SA) Subsystem configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility –...
IMB-H810-i2 microATX Motherboard 5.4.1 PCH-IO Configuration Use the PCH-IO Configuration menu (BIOS Menu 19) to configure the PCH chipset. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset Auto Power Button Status [Disabled (ATX)] Select AC power state when power is re-applied Restore AC Power Loss [Last State]...
IMB-H810-i2 microATX Motherboard Enabled Power Saving Function support enabled PCIEX16 Power [1 x16 PCIE] Use the PCIEX16 Power BIOS option to configure the PCIe x16 channel mode on the motherboard. 1 x16 PCIE Configure the PCIe x16 slot as one PCIe x16 EFAULT ...
IMB-H810-i2 microATX Motherboard Enabled Detect if a non-compliance PCI Express device is connected to the PCI Express port. 5.4.1.2 PCH Azalia Configuration Use the PCH Azalia Configuration submenu (BIOS Menu 21) to configure the PCH Azalia codec. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset PCH Azalia Configuration Control Detection of the...
IMB-H810-i2 microATX Motherboard 5.4.2 System Agent (SA) Configuration Use the System Agent (SA) Configuration menu (BIOS Menu 22) to configure the video device connected to the system. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced VT-d [Disabled] Check to enable VT-d function on MCH.
IMB-H810-i2 microATX Motherboard 5.4.2.1 Graphics Configuration Use the Graphics Configuration submenu (BIOS Menu 23) to configure the graphics settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset Graphics Configuration Primary Display [Auto] DVMT Pre-Allocated [256M] --------------------- : Select Screen DVMT Total Gfx Mem [MAX] ...
Page 124
IMB-H810-i2 microATX Motherboard 128M 128 MB of memory used by internal graphics device 256 MB of memory used by internal graphics 256M EFAULT device 512M 512 MB of memory used by internal graphics device DVMT Total Gfx Mem [MAX] Use the DVMT Total Gfx Mem option to specify the maximum amount of memory that can be allocated as graphics memory.
IMB-H810-i2 microATX Motherboard Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset LCD Control Select the Video Device which will be activated Primary IGFX Boot Display [VBIOS Default] during POST. This has no effect if external graphics present. Secondary boot display selection will appear based on your selection.
IMB-H810-i2 microATX Motherboard 5.4.2.2 NB PCIe Configuration Use the NB PCIe Configuration submenu (BIOS Menu 25) to configure the northbridge PCIe settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset NB PCIe Configuration PEG0 Not Present PEG0-Gen X [Auto] --------------------- : Select Screen...
IMB-H810-i2 microATX Motherboard Detect Non-Compliance Device [Disabled] Use the Detect Non-Compliance Device option to detect non-compliance PCIe device in PEG. Disabled Do not detect non-compliance PCIe device in PEG EFAULT Detect non-compliance PCIe device in PEG Enabled 5.4.2.3 Memory Configuration Use the Memory Configuration submenu (BIOS Menu 26) to configure the Memory settings.
IMB-H810-i2 microATX Motherboard 5.5 Boot Use the Boot menu (BIOS Menu 27) to configure system boot options. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Server Mgmt Boot Configuration Select the keyboard Bootup NumLock State [On] NumLock state...
Page 129
IMB-H810-i2 microATX Motherboard Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Normal POST messages displayed Disabled Enabled OEM Logo displayed instead of POST messages EFAULT Option ROM Messages [Force BIOS] Use the Option ROM Messages option to set the Option ROM display mode.
IMB-H810-i2 microATX Motherboard 5.6 Security Use the Security menu (BIOS Menu 28) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Server Mgmt Password Description Set Administrator Password If ONLY the Administrator’s password is set,...
IMB-H810-i2 microATX Motherboard Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Server Mgmt Save Changes and Reset Exit the system after Discard Changes and Reset saving the changes. Restore Defaults Save as User Defaults Restore User Defaults ---------------------...
IMB-H810-i2 microATX Motherboard 5.8 Server Management Use the Server Mgmt menu (BIOS Menu 30) to configure BMC network parameters. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Server Mgmt BMC Self Test Status FAILED Configure BMC network parameters...
IMB-H810-i2 microATX Motherboard 5.8.1 System Event Log Use the System Event Log menu (BIOS Menu 31) to configure the system event log of the BMC. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Server Mgmt Enabling/Disabling Options Change this to enable or SEL Components [Enabled] disable all features of...
Page 134
IMB-H810-i2 microATX Motherboard Yes, On Erase system event log on every reset. every reset When SEL is Full [Do Nothing] Use the When SEL is Full option to select an reaction to a full SEL. Do not do anything when SEL is full. Do Nothing EFAULT ...
IMB-H810-i2 microATX Motherboard 5.8.2 BMC Network Configuration Use the BMC Network Configuration menu (BIOS Menu 32) to configure the BMC network parameters. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Server Mgmt BMC network configuration Select to configure LAN channel parameters Lan channel 1 statically or...
IMB-H810-i2 microATX Motherboard 6.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system: ...
IMB-H810-i2 microATX Motherboard Figure 6-1: Introduction Screen Step 3: Click IMB-H810. Step 4: A new screen with a list of available drivers appears (Figure 6-2). Figure 6-2: Available Drivers Step 6: Install all of the necessary drivers in this menu. Page 122...
IMB-H810-i2 microATX Motherboard 6.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “1-Chipset”. Step 3: Locate the setup file and double click on it. Step 4: When the setup files are completely extracted, the Welcome Screen in Figure 6-3 appears.
IMB-H810-i2 microATX Motherboard Step 11: Setup Operations are performed as shown in Figure 6-6. Step 12: Once the Setup Operations are complete, click Next to continue. Figure 6-6: Chipset Driver Setup Operations Step 13: The Finish screen in Figure 6-7 appears. Step 14: Select “Yes, I want to restart this computer now”...
IMB-H810-i2 microATX Motherboard Figure 6-7: Chipset Driver Installation Finish Screen 6.4 Graphics Driver Installation To install the Graphics driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “2-Graphics” and select the folder which corresponds to the operating system.
IMB-H810-i2 microATX Motherboard Step 8: The Read Me file in Figure 6-10 appears. Click Next to continue. Figure 6-10: Graphics Driver Read Me File Step 9: Setup Operations are performed as shown in Figure 6-11. Step 10: Once the Setup Operations are complete, click Next to continue. Figure 6-11: Graphics Driver Setup Operations Page 128...
IMB-H810-i2 microATX Motherboard Step 11: The Finish screen in Figure 6-12 appears. Step 12: Select “Yes, I want to restart this computer now” and click Finish. Step 0: Figure 6-12: Graphics Driver Installation Finish Screen 6.5 LAN Driver Installation To install the LAN driver, please do the following. Step 1: Right-click the Computer button from the start menu and select Properties.
IMB-H810-i2 microATX Motherboard Figure 6-13: Windows Control Panel Step 2: The system control panel window in Figure 6-14 appears. Step 3: Click the Device Manager link (Figure 6-14). Figure 6-14: System Control Panel Step 4: A list of system hardware devices appears (Figure 6-15). Step 5: Right-click one of the Ethernet controllers that has question marks next to it (this means Windows does not recognize the device).
IMB-H810-i2 microATX Motherboard Figure 6-16: Update Driver Software Window Step 8: Select “Browse my computer for driver software” and click N to continue. Step 9: Click Browse to select “X:\3-LAN” directory in the Locate File window, where “X:\” is the system CD drive. (Figure 6-17). Figure 6-17: Locate Driver Files Step 10: Click N...
IMB-H810-i2 microATX Motherboard Figure 6-18: LAN Driver Installation Step 12: The Finish screen appears. Click Close to exit. Step 13: Right-click the other Ethernet controller that has question marks next to it as shown in Figure 6-15. Repeat Step 6 Step 12 to install the second Ethernet controller driver.
IMB-H810-i2 microATX Motherboard Step 3: Locate the setup file and double click on it. Step 4: A Welcome Screen appears (Figure 6-19). Step 5: Click Next to continue. Figure 6-19: USB 3.0 Driver Welcome Screen Step 6: The license agreement in Figure 6-20 appears. Step 7: Read the License Agreement.
IMB-H810-i2 microATX Motherboard Figure 6-20: USB 3.0 Driver License Agreement Step 9: The Read Me file in Figure 6-21 appears. Step 10: Click Next to continue. Figure 6-21: USB 3.0 Driver Read Me File Step 11: Setup Operations are performed as shown in Figure 6-22. Step 12: Once the Setup Operations are complete, click Next to continue.
IMB-H810-i2 microATX Motherboard 6.7 Audio Driver Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps below. 6.7.1 BIOS Setup Step 1: Enter the BIOS setup. To do this, reboot the system and press D during POST. Step 2: Go to the PCH Azalia Configuration submenu.
IMB-H810-i2 microATX Motherboard Figure 6-24: InstallShield Wizard Welcome Screen Step 6: Click Next to continue the installation. Step 7: InstallShield starts to install the new software as shown in Figure 6-25. Figure 6-25: Audio Driver Software Configuration Step 8: After the driver installation process is complete, a confirmation screen appears (Figure 6-26).
IMB-H810-i2 microATX Motherboard Figure 6-26: Restart the Computer Step 9: The confirmation screen offers the option of restarting the computer now or later. For the settings to take effect, the computer must be restarted. Click Finish to restart the computer. Step 0: Page 139...
Page 157
IMB-H810-i2 microATX Motherboard DECLARATION OF CONFORMITY This equipment has been tested and found to comply with specifications for CE marking. If the user modifies and/or installs other devices in the equipment, the CE conformity declaration may no longer apply. FCC WARNING This equipment complies with Part 15 of the FCC Rules.
Page 159
IMB-H810-i2 microATX Motherboard Below is a list of BIOS configuration options in the BIOS chapter. System Date [xx/xx/xx] ......................72 System Time [xx:xx:xx] .......................72 ACPI Sleep State [S1 (CPU Stop Clock)] ................74 Wake System with Fixed Time [Disabled] .................75 ...
Page 160
IMB-H810-i2 microATX Motherboard Change Settings [Auto] .......................93 Serial Port [Enabled]......................94 Change Settings [Auto] .......................94 Serial Port [Enabled]......................95 Change Settings [Auto] .......................95 Serial Port [Enabled]......................96 Change Settings [Auto] .......................96 Device Mode [RS232]......................96 Console Redirection [Disabled] ..................98 ...
Page 161
IMB-H810-i2 microATX Motherboard UEFI Boot [Disabled] ......................113 Administrator Password ....................114 User Password ........................114 Save Changes and Reset ....................115 Discard Changes and Reset .................... 115 Restore Defaults ....................... 115 Save as User Defaults ...................... 115 ...
Page 163
IMB-H810-i2 microATX Motherboard AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface.
Page 164
IMB-H810-i2 microATX Motherboard DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. The digital inputs and digital outputs are general control signals that control the on/off circuit of external devices or TTL devices.
Page 165
IMB-H810-i2 microATX Motherboard LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer. POST The Power-on Self Test (POST) is the pre-boot actions the system performs when the system is turned-on. Random Access Memory (RAM) is volatile memory that loses data when power is lost.
Page 167
IMB-H810-i2 microATX Motherboard NOTE: The following discussion applies to DOS environment. Contact IEI support or visit the IEI website for specific drivers for other operating systems. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMIs or a software bug.
Page 168
IMB-H810-i2 microATX Motherboard NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EXAMPLE PROGRAM: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds ;...
IMB-H810-i2 microATX Motherboard E.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
Page 171
IMB-H810-i2 microATX Motherboard Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl (CR(VI)) (PBB) Ethers (PBDE) Housing Display Printed Circuit Board Metal Fasteners Cable Assembly Fan Assembly Power Supply Assemblies Battery This toxic or hazardous substance is contained in all of the homogeneous materials for the part is...