Table of Contents
Advertisement
Web screen configurations (continued)
SNMPv3 ‑ User name
Input the user name for user authentication.
The user name that you input here will need to be specified in the
SNMPv3 manager.
Maximum number
0 to 32 characters
of characters
Invalid characters
Full-size characters
Factory settings: blank
SNMPv3 ‑ Authentication
Sets the algorithm to be used for user authentication.
Setting value:
MD5
The MD5 algorithm will be used for user authentication.
SHA1
The SHA1 algorithm will be used for user authentication.
Factory settings: MD5
SNMPv3 ‑ Encryption method
Sets the encryption method to be used for transmissions.
Setting value:
DES encryption method for SNMPv3 will be used for
DES
transmissions.
AES encryption method for SNMPv3 will be used for
AES
transmissions.
Factory settings: DES
SNMPv3 ‑ Password
Sets the password to be used for user authentication.
The password that you input here will need to be specified in the
SNMPv3 manager.
When [Authentication] is set to [MD5]:
Maximum number
8 to 16 characters
of characters
When [Authentication] is set to [SHA1]:
8 to 20 characters
Invalid characters
Full-size characters
Factory settings: blank
System name
Input the name of the system to control the unit with the SNMP
function.
Maximum number
0 to 32 half-size characters
of characters
Invalid characters
Full size characters
Factory settings: blank
Location
Input the location where the unit has been installed.
Maximum number
0 to 32 half-size characters
of characters
Factory settings: blank
Contact
Input the email address or telephone number of the administrator.
Maximum number
0 to 255 half-size characters
of characters
Invalid characters
Full size characters
Factory settings: blank
z Diffserv
„
This performs settings relating to the Diffserv function. The Diffserv
function sets the priority of image/audio data transmitted from the
router.
Priorities set to this unit must be aligned with DSCP values set to the
router.
To use the Diffserv function, consult your network administrator.
DSCP(0‑63)
Input the packet priority.
Maximum number
0 to 63 half-size characters
of characters
Factory settings: 0
z RTSP
„
This performs settings related to the RTSP function. The RTSP
function sets the RTSP transmission port and RTSP Request URL
used during IP image transmission.
RTSP port
Sets the RTSP reception port no.
Port Nos. that can be selected: 1 to 65535
The following port numbers are used by the unit so they cannot be
used.
20, 21, 23, 25, 42, 53, 67, 68, 69, 80, 110, 123, 161, 162, 443, 995,
10669, 10670, 59000 to 61000
Factory settings: 554
RTSP Request URL (1) to (4)
Sets up the URL for RTSP when making IP image transmission
demands to this unit.
RTSP Request URL (1)
RTSP Request URL (2)
RTSP Request URL (3)
RTSP Request URL (4)
Factory settings:
RTSP Request URL (1)
RTSP Request URL (2)
RTSP Request URL (3)
RTSP Request URL (4)
• Up to 255 characters can be entered.
• The following characters can be displayed.
Half-size numeric
0123456789
characters
Half-size alphabetical
ABCDEFGHIJKLMNOPQRSTUVWXYZ
characters (upper and
abcdefghijklmnopqrstuvwxyz
lower cases)
Half-size symbols
/ - _
<NOTE>
• RTSP Request URLs (1) to (4) cannot have the same URL.
91
RTSP URL for H.264 (1) image
transmission
RTSP URL for H.264 (2) image
transmission
RTSP URL for H.264 (3) image
transmission
RTSP URL for H.264 (4) image
transmission
MediaInput/h264/stream_1
MediaInput/h264/stream_2
MediaInput/h264/stream_3
MediaInput/h264/stream_4
Advertisement
Table of Contents
