Maintenance; Residual Risk; Risk Reduction - Ryobi OGS1822 Original Instructions Manual

MAINTENANCE

WARNING
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can
cause possible injury, contribute to poor performance,
and may void your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For service, bring the product to an
authorised service centre for repair. When servicing, use
only original replacement parts.
■ Use gloves when maintaining the cutting means.
■ Maintain the product with care. Keep the cutter edge
sharp and clean for best performance and to reduce
the risk of injury. Follow instructions for lubricating and
changing accessories. Keep handles dry, clean, and
free from oil and grease.
■ Switch off the product and remove the battery pack
before conducting any maintenance or cleaning work.
■ After each use, clean the body and handles with a soft,
dry cloth.
■ After each use, clean the debris from the blades with a
stiff brush, and then carefully apply a rust preventative
lubricant before refitting the blade sheath. The
manufacturer recommends you use a rust preventative
and lubricant spray to apply an even distribution and
reduce the risk of personal injury from contact with
the cutter blades. For information about suitable spray
product, check with an authorised service centre.
■ Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types
of commercial solvents and may be damaged by their
use. Use clean cloths to remove dirt, dust, oil, and
grease.
■ Always ensure that the ventilation openings are kept
clear of debris.
■ Periodically inspect the cutting means for damage and
wear.
■ Always use the manufacturer's specified replacement
blades.
■ For easier operation and longer blade life, lubricate
the cutter blades before and after each use. Before
lubricating, remove the battery pack and lay cutter
blades on a flat surface. Apply lightweight machine oil
along the edge of the top blade. Do not apply oil when
the product is running.

RESIDUAL RISK

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use, and the
operator should pay special attention to avoid the following:
4 | English
■ Injury caused by vibration
– Hold the product by designated handles and restrict
working time and exposure.
■ Injury caused by exposure to noise
– Wear hearing protection and limit exposure.
■ Injury caused by contact with the blades
– The blade cannot be guarded while cutting. Keep
the blade away from yourself and others. Cover it
with the blade sheath when the product is not in
use.

RISK REDUCTION

It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome.
Symptoms may include tingling, numbness and blanching
of the fi ngers, usually apparent upon exposure to cold.
Hereditary factors, exposure to cold and dampness, diet,
smoking and work practices are all thought to contribute
to the development of the these symptoms. There are
measures that can be taken by the operator to possibly
reduce the effects of vibration:
■ Keep your body warm in cold weather. When operating
the product wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
■ After each period of operation, exercise to increase
blood circulation.
■ Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician.
WARNING
Injuries may be caused, or aggravated by prolonged use
of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
KNOW YOUR PRODUCT
See page 139.
1. Rear handle
2. Trigger lock button
3. Trigger
4. Grass shear blade
5. Grass shear blade sheath
6. Shrubber blade
7. Shrubber blade sheath
8. Battery pack
9. Battery latch button
10. Charger
11. Blade securing knob
12. Blade post
13. Rubber socket port cover