[Startup Input Select]; [Last Used] - Panasonic PT-DX810E Operating Instructions Manual

9)
Press qw to switch [COMMAND].
f The setting will change among [POWER ON], [STANDBY],
[SHUTTER] *1 , [INPUT] *1 , [LAMP SELECT]
and [SIDE BY SIDE] each time you press the button.
*1*2
*1 The details set in step 11) are displayed.
*2 Only for PT-DW740E
10)
Press the <ENTER> button.
f The [COMMAND] detailed screen is displayed.
r [COMMAND]
[POWER ON]
[STANDBY]
[SHUTTER]
[INPUT]
[LAMP SELECT]
[LAMP POWER]
[SIDE BY SIDE] *
* Only for PT-DW740E
Note
f If you try to register a setting that would cause the lamp to flash for a short time, an error message will be displayed on the screen. Set the
time and command again.
f To delete a command already set, press the <DEFAULT> button on the Step 5) screen, or select [DELETE] on the Step 6) screen and press
the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. ( x page 83)
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with this function may not be executed.

[STARTUP INPUT SELECT]

Set the input signal to be projected when the projector is switched on.
1)
Press as to select [STARTUP INPUT
SELECT].
r [STARTUP INPUT SELECT]

[LAST USED]

[RGB1]
[RGB2]
[VIDEO]
Chapter 4 Settings — [PROJECTOR SETUP] menu
*1 , [LAMP POWER]
― Turns the power on.
― Enters standby.
[OPEN]
Opens the shutter.
[CLOSE] Closes the shutter.
[RGB1] Switches the input to RGB1.
[RGB2] Switches the input to RGB2.
[VIDEO] Switches the input to VIDEO.
[S-VIDEO] Switches the input to S-VIDEO.
[DVI-D] Switches the input to DVI-D.
[HDMI] Switches the input to HDMI.
[DUAL] Turns on both lamps.
Turns on one lamp. (The lamp is automatically selected which has shorter
[SINGLE]
cumulative operating time.)
[NORMAL] Sets the high luminance of the lamp.
[ECO] Sets lower luminance of the lamp than [NORMAL].
[OFF] Displays the side-by-side screen.
[ON]
Cancels the side-by-side screen.
Keeps the input selected last.
Sets the input to be projected when the projector is switched on to RGB1.
Sets the input to be projected when the projector is switched on to RGB2.
Sets the input to be projected when the projector is switched on to VIDEO.
11)
Press as to select a command.
f [OPEN]/[CLOSE] in [SHUTTER], [RGB1]/[RGB2]/[VIDEO]/
*1 [S-VIDEO]/[DVI-D]/[HDMI] in [INPUT], [DUAL]/[SINGLE] in
[LAMP SELECT], [NORMAL]/[ECO] in [LAMP POWER], and
[OFF]/[ON] in [SIDE BY SIDE] will change each time you press
qw .
12)
Press the <ENTER> button.
f The command is fixed and ● is displayed at the left of the
selected command.
f After the command is fixed, press the <MENU> button to close
the detailed setting menu.
13)
Press as to select [STORE], and press the
<ENTER> button.
2)
Press qw to switch [STARTUP INPUT
SELECT].
f The setting will change among [LAST USED], [RGB1], [RGB2],
[VIDEO], [S-VIDEO], [DVI-D] and [HDMI] each time you press
the button.
ENGLISH - 79