Diamond 350/BSS-N Operating And Maintenance Manual
  1. Manuals
  2. Brands
  3. Diamond Manuals
  4. Kitchen Appliances
  5. 350/BSS-N
  6. Operating and maintenance manual

Diamond 350/BSS-N Operating And Maintenance Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
04/2015
Mod: 350/BSS-N
Production code: 15352202S

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 350/BSS-N and is the answer not in the manual?

Questions and answers

Related Manuals for Diamond 350/BSS-N

Summary of Contents for Diamond 350/BSS-N

  • Page 1 04/2015 Mod: 350/BSS-N Production code: 15352202S...
  • Page 2 Professional slicers CE Operating and Maintenance Manual...
  • Page 3 CHAP. 6 - ROUTINE CLEANING page 23 INTRODUCTION - GENERALITIES This manual has been re-presented to provide the Client with all the information on - CLEANING THE MACHINE 6.2.1 - Cleaning the goods holder plate the machine and its safety regulations, and also the use and maintenance instructions 6.2.2 - Cleaning the blade, the bladeguard and the ring which permit using the machine in the best way and maintaining its efficiency...
  • Page 4 CHAP. 1 - RECEIVING THE MACHINE Do not expose the package to humidity 1.1 - PACKAGE or rain (Fig. n°4). The slicer is shipped in a package which consists of (Fig. n°1): cardboard box, Fig. n°4 wooden pallets and protective nylon. They should be disposed of separately and according to the norms in force in the country of installation.

  • Page 5: Chap. 2 - Installation

    the documents, make a precise report on the damage to the machine. Do not 2.2 - POSITIONING overturn the package!! When transporting it make sure that it is firmly held by the four corners (keeping it parallel to the floor). Position the pallet, with the slicer, on a flat surface and take off (a) the cap from the slicer (Fig.

  • Page 6: Electrical Connection

    2.3.4 - Slicer with 230 V. three-phase motor 2.3 - ELECTRICAL CONNECTION The slicer is equipped with a feeding cable with a section area of 5x1mm²; length 1.5m and a blue 15A 3F + T CEI plug. Check that the data reported on the Connect the slicer 230 V.

  • Page 7: Preliminary Check

    2.5 - PRELIMINARY CHECK 2.4.1 - 115 V. tension selection Before testing make sure the goods holder plate is well-blocked, after which test functioning with the following procedure: “OFF” button Push the “ON” push-button and the “OFF” push-button Fig. n°22; check if by unscrewing the blade guard tie rod the machine stops working;...

  • Page 8: Construction Features

      Do not pull the slicer or the feeding cable The slicer must only be used by (Fig. n°29) to unplug it. trained personnel who know the  Regularly check the state of the fee- safety norms contained in this manual ding cable;...

  • Page 9: Safety Devices Installed On The Machine

    LEGEND: 4.2 - SAFETY DEVICES INSTALLED ON THE MACHINE 1 - Cap 14 - Ring 4.2.1 - Mechanical safety 2 - Bladeguard tie rod hand grip 15 - Cap hand grip As far as mechanical safety is concerned, the slicer described in this manual 3 - Thickness gauge plane 16 - Goods presser hand grip responds to:...

  • Page 10: Description Of The Machine

    - A relay in the control circuit, that re- TAB. n°1 - DIMENSION MEASUREMENTS AND TECHNICAL FEATURES quires the machine to start up again in case of an accidental loss of electri- MODEL U.m. MT 300 - 330 - 350 city (Fig.
  • Page 11 TAB. n°2 - DIMENSION MEASUREMENTS AND TECHNICAL FEATURES TAB. n°3 - DIMENSION MEASUREMENTS AND TECHNICAL FEATURES MODEL U.m. MT 300 - 330 - 350 MODEL U.m. MT 300 - 330 - 350 Blade diameter Blade diameter 468x338 468x338 468x338 468x338 468x338 468x338 CxDxE...

  • Page 12: Operational Check

    CHAP. 5 - MACHINE USE 5.2 - LOADING AND CUTTING THE PRODUCT WARNING: The goods to be cut are loaded on the hopper only with the gradua- 5.1 - OPERATIONAL CHECK ted hand grip at “0” and the motor stopped, being careful with the blade and the points.

  • Page 13: Sharpening The Blade

    or rough surface, therefore thecutting effort increases (chapter 5.3). 7. press the 2 push-buttons (2 and 3) contemporaneously for 3/4 sec. and release them in the same instant (Fig. n°46); 5.3 - SHARPENING THE BLADE 8. after having completed the sharpe- ning it is advisable to clean the grin- WARNING: Before starting to sharpen the blade, pay attention to RESI- ders and the blade (chapter 6.2.3);...
  • Page 14 6.2.3 - Cleaning the sliceguard having taken off the trolley, the goods (Fig. n°52) holder plate can be carefully cleaned To remove the sliceguard simply grasp with warm water, the equipped deter- the hand grip (1) and pull up so that the gent or neutral detergent (pH 7).

  • Page 15: Chap. 7 - Maintenance

    CHAP. 7 - MAINTENANCE CHAP. 8 - DISMANTLING 7.1 - GENERALITIES 8.1 - OUT OF SERVICE Before carrying out any maintenance operations it is necessary to: If for some reason it is decided to put the machine out of service, make sure that a) disconnect the feed plug from the electrical network to completely isolate it cannot be used by anyone: detach or cut the electrical connections.

This manual is also suitable for:

15352202s

Table of Contents