Related Manuals for DAVIS 6322C
Summary of Contents for DAVIS 6322C
- Page 1 USER MANUAL Integrated Sensor Suite ™ For Vantage Pro2 , Vantage Pro2 GroWeather ™ and Vantage Pro2 Plus Davis Instruments, 3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A. • 510-732-9229 • www.davisnet.com...
-
Page 2: Table Of Contents
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modification not expressly approved in writing by Davis Instruments may void the warranty and void the user's authority to operate this equipment. FCC ID: IR2DWW6328... -
Page 3: Introduction
Introduction The Integrated Sensor Suite (ISS) collects outside weather data and sends the data to a Vantage Pro2 console. The wireless ISS can also transmit data to wireless Vantage Connect, Vantage Vue console, Envoy8X, or wireless Weather Envoy. The wireless ISS is solar-powered and sends data via radio. -
Page 4: Included Components And Hardware
Included Components and Hardware The ISS comes with all the components and hardware shown in the following illustrations. If you purchased your ISS as part of a weather station package containing the Vantage Pro2 console, additional components may be included in the package that are not shown here. - Page 5 Other versions of the ISS have additional features and parts: VANTAGE PRO2 with 24-Hour Fan-Aspirated Shield VANTAGE PRO2 PLUS with Standard Radiation Shield Antenna (wireless only) UV and Solar Radiation Sensors Transmitter Solar Panel Antenna (wireless only) (wireless only) Transmitter Solar Panel Solar Panel (wireless only)
- Page 6 Hardware (Included) Bird Spikes (15) U-Bolts 1/4" x 3" Lag Screws 1/4" Flat Washers #4 x 1-1/8" Machine Screw 1/4" Lock Washers #4 Tooth 1/4" Hex Nuts 3-Volt Lock Washer Lithium .05" Allen Battery Backing Plate #4-40 Hex Nut (wireless Wrench models only)
-
Page 7: Prepare The Iss For Installation
Prepare the ISS for Installation Follow the steps in the order they are presented as each builds on tasks completed in previous steps. These steps apply to all versions of the ISS, unless otherwise noted. Tip: Use a well-lit work table or work area to prepare the ISS for installation. Assemble the Anemometer The anemometer measures wind direction and speed. - Page 8 4. Slide the tooth-lock washer and hex nut onto the machine screw. Tighten the hex nut while holding the screw with a Phillips head screwdriver to prevent it from turning. 5. Press the sensor cable firmly and completely into the zig-zagging channel in the base, starting from the arm and progressing downward to the bottom of the base.
- Page 9 Check Sensor Interface Connections and Connect the Anemometer Cable The sensor interface is located in the transmitter shelter on the front of the ISS station. It contains all the connections for the weather sensors of the ISS. Follow the steps below to check the sensor interface and ensure that all sensors are connected properly.
- Page 10 Check the Factory Installed Sensor Connections 1. Verify that the rain collector and temperature/humidity sensor cables are plugged into the receptacles labeled RAIN and TEMP/HUM on the sensor interface. 2. If your ISS includes UV and/or solar radiation sensors, verify that the sensor cables are plugged into the receptacles labeled UV and SUN on the sensor interface.
- Page 11 Prepare the Rain Collector The tipping mechanism is secured at the factory to protect it from damage during shipping. Note: Be careful not to scratch the silver-colored coating on the tipping spoons under the cone. 1. Remove the rain collector cone from the ISS base by rotating the cone counter-clockwise.
- Page 12 Optional: Insert the Metric Measurement Adapter The rain collector tipping spoon mechanism takes measurements in 0.01'' (US versions) or 0.2 mm (M, EU, UK and OV) increments for each tip of the spoons. If you have a US version and would like to convert it to a metric measurement, you can insert the metric adapter that is included in your hardware kit.
- Page 13 4. Separate an end cap from one end of the magnet. Top (closed) 5. Slide the magnet, exposed end of magnet first, into the open slot of the metric adapter. Bottom (notched) 6. Insert the metric adapter and magnet between the arms of the spoons, with the top (solid side) of the metric adapter facing up.
-
Page 14: Cabled Iss Assembly
The 100' (30 m) console cable provides power to the ISS and is used to send data from the ISS to the console. The console cable can be extended up to 1000' (305 m) in length with extension cables purchased from Davis Instruments. With the console powered, plugging the console cable into the console powers the ISS and establishes communication between the ISS and the console. - Page 15 Verify Data from the ISS Sensors 1. Near the center of the screen, look for the outside temperature (TEMP OUT). 2. Spin the wind cups to check wind speed, pressing WIND if necessary to alternate between speed and direction in the compass rose. 3.
- Page 16 AC power adapter from the console and removing the console batteries for at least 30 seconds. If the console is still not displaying sensor readings from the ISS after powering back up, please contact Davis Technical Support.
-
Page 17: Wireless Iss Assembly
Note: If there is another Davis weather station within range of your console or Vantage Connect, you should change the Transmitter ID. Remember to use the same ID for the ISS and console. See “Optional: Changing ISS Transmitter ID” on page 18. - Page 18 Verifying Data from the ISS Sensors Use these steps to verify reception of ISS data at the wireless Vantage Pro2 console and to test the operation of the ISS sensors. 1. If the console is in Setup Mode, press and hold DONE until the Current Weather screen displays.
- Page 19 Troubleshooting Wireless ISS Reception If the console isn’t displaying data from the ISS, perform the following steps: 1. Verify that the console is powered and is not in Setup Mode. 2. Make sure that all ISS sensor cables are firmly connected to the sensor interface and the ISS battery is properly installed.
- Page 20 Change the Transmitter ID if any of the following issues are true: • Another Davis Instruments wireless weather station operating nearby already uses Transmitter ID 1. • You have purchased additional Vantage Pro2 or Vantage Vue wireless transmitting stations and one of the stations has been designated as Station No.
- Page 21 Using Multiple Transmitting Stations This table shows the maximum number of each type of station that can be used with The console can receive signals from a total of up a single Vantage Pro2 console. to eight transmitters (stations). Station Type Maximum Number Integrated Sensor Suite (ISS) Anemometer Transmitter Kit*...
-
Page 22: Plan The Iss Installation
Plan the ISS Installation Locating the ISS and Anemometer For the weather station to perform at its best, use these guidelines to select the optimum mounting locations for the ISS and anemometer. Be sure to take into consideration ease of access for maintenance, sensor cable lengths and wireless transmission range when siting the station. - Page 23 • If mounting on a roof, mount the anemometer at least 7' (2.1 m) above the roof apex. (When using a Davis Mounting Tripod, install the anemometer at the very top of the pole).
- Page 24 Optional: Wireless Transmission Considerations The range of the radio transmission depends on several factors. Try to position the transmitter and the receiver as close as possible for best results. Typical maximum ranges include: • Line of sight: 1000' (300 m). •...
- Page 25 Testing Wireless Transmission at ISS Location After a suitable place has been found for the wireless ISS, it is very important to test reception from the installation location before permanently mounting it there. 1. Set the ISS in the desired installation location. 2.
-
Page 26: Install The Iss
ISS could be mounted on a fence closer to ground level. • If you would like to install your anemometer even farther away from the ISS or without using a cable, use a Davis Anemometer Transmitter Kit, product number 6332. - Page 27 General ISS Installation Guidelines • Install the ISS as level as possible to ensure accurate rain measurements. Use the built-in bubble level (under the rain collector cone, near the tipping spoons mechanism) or carpenter’s level to make sure the ISS is level. •...
- Page 28 Installation Options There are several ways to mount and install the ISS unit. The following installations are recommended. Individual ISS locations and installations may vary. • Installing the ISS and anemometer on a post or flat surface • Installing the ISS and anemometer on a pole, together or separately Note: All installations require that the rain collector cone be removed for assembly.
- Page 29 1. With a 3/16" (5 mm) drill bit, drill two holes approximately 2 " (54 mm) apart. Use a carpenter’s level to ensure the holes will be level. 2. Insert the 1/4" x 3" lag screws through the flat washers and the holes in the anemometer mounting base into the post.
- Page 30 Installing the ISS and Anemometer on a Pole Built-in bubble level behind tipping spoon mechanism U-Bolts: Anemometer U-Bolt Rain Collector U-Bolt 1/4" Hex Nut 1/4" Lock Washer Backing Plate 1/4" Flat Washer 1/4" Lock Wash 1/4" Hex Nu Tipping spoon not shown for clarity.
- Page 31 Guidelines for Installing the ISS on a Pole • When mounting the rain collector base and anemometer together on opposite sides of the pole, remember that whichever side is mounted first, the U-bolt from the opposite side must also be placed around the pole before tightening the U- bolts.
- Page 32 Option 2: Installing ISS Only 1. While holding the mounting base against the pole, place the two ends of a U-bolt around the pole and through the two holes in the base. 2. Slide the metal backing plate over the bolt ends as they stick out toward the rain collector cone.
- Page 33 Finish the Installation Close the Transmitter Shelter 1. If the solar panel cable (or the optional fan cable) were disconnected during ISS assembly, reconnect them. 2. Find the two raised alignment indicator lines on both the shelter and the cover. Match these alignment indicators as you place the cover against the box.
- Page 34 Level the Solar and UV Sensors If you have an ISS that includes a solar radiation and/or UV sensor, use the bubble level on the sensors as a guide to verify that the sensors are level. Adjust the level by tightening or loosening the three screws that hold Solar Radiation Sensor Top should be even with or...
- Page 35 • Wireless Temperature Station (#6372) • Wireless Temperature/Humidity Station (#6382) • Wireless Leaf & Soil Moisture/Temperature Station (#6345) For more details, please visit our website or see the most recent Davis Precision Weather Instruments catalog.
-
Page 36: Maintenance And Troubleshooting
Turn the shafts the cups and vane rotate on.While the wind direction shaft should have more resistance than the wind cup shaft, if either feels gritty or stiff, contact Davis Technical Support. Reattach the cups and van and tighten with the Allen wrench. - Page 37 Maintaining the Radiation Shield The outer plating of the radiation shield should be cleaned when there is excessive dirt and build-up on the plating. Wipe the outer edge of each ring with a damp cloth. Note: Spraying down or using water excessively to clean the radiation shield can damage the sensitive sensors or alter the data and readings the ISS is transmitting.
- Page 38 Maintaining a 24-Hour Fan-Aspirated Radiation Shield The cross-section diagram shows how the 24- Hour Fan-Aspirated Radiation Shield draws outside air up through the sensor chamber and MOTOR between the three walls surrounding the sensor chamber, while the shield stack prevents radiation heating of the outer wall.
- Page 39 2. Remove the rain collector cone. 3. Using a Phillips head 1-1/4" Screw Lock Washer screwdriver, remove the three Flat Washer screws connecting the rain collector base to the threaded spacers. 4. While removing the screws, support the radiation shield from the bottom.
- Page 40 8. Remove the white junction board cover and unplug the fan Fan Unit power cable from the junction board. Fan Power Cable Fan Deflector Fan Unit Temp/Hum 9. Lift out the fan and fan Sensor Cable Junction Board and the fan deflector. Channel Cover (removed) Temp/Hum...
- Page 41 15. Replace the fan and plug the fan power cable back into the junction board. The fan should start to rotate. Replace the junction board cover. 16. Replace the two cap plates. (Note that the closed plate goes on top.) Replace the solar bracket and the threaded spacers, Threaded Spacer...
- Page 42 Daytime Fan-Aspirated Radiation Shield The Daytime Fan-Aspirated radiation shield has a fan that is powered by a solar panel. It differs from the 24-Hour Fan in that it has no batteries. This causes it operate during the daytime when solar radiation effects are of the greatest concern, and to stop at night.
- Page 43 5. Unscrew the three threaded spacers. Threaded Spacer 6. Remove the three screws from the bottom of the radiation shielding Fan Plate and separate the shield stack, taking care to maintain the order in which the plates are assembled. 7. Remove all debris from inside the shield and wipe the interior surfaces.
- Page 44 Maintaining the Rain Collector Cone To maintain accuracy, thoroughly clean the rain collector several times a year. Note: Cleaning the rain collector and tipping spoons may cause false rain readings. Unplug the rain sensor from the sensor interface before cleaning so that no inaccurate readings are logged, or clear the weather data that was logged on the Vantage Pro2 console after cleaning is complete.
-
Page 45: Contacting Technical Support
Do not lubricate the shaft or bearings in any way. When replacing the cups, make sure they are not rubbing against any part of the anemometer head. Contacting Technical Support For questions about the ISS or Vantage Pro2 system, please contact Davis Technical Support. We’ll be glad to help. Note: Please do not return items to the factory for repair before calling to get a Return Materials Authorization number. -
Page 46: Appendix: Specifications
License: ......Low power (less than 8 mW), no license required Primary power: ..... Solar power – Davis solar charger Backup power: . - Page 48 Vantage Pro2™, Weather Envoy™, Envoy8X™, Vantage Vue® and Vantage Connect® are trademarks of Davis Instruments Corporation, Hayward, CA. Copyright © 2017 Davis Instruments Corp. All rights reserved. Information in this document subject to change without notice. Davis Instruments Quality Management System is ISO 9001 certified.