Table of Contents
Advertisement
Caution!
Do not use any sharp or abrasive medium or a glass scraper.
The glass could be damaged.
Refitting the intermediate panel:
Place the intermediate panel in the supports on the left and
1.
right (Fig. D).
Push the intermediate panel downwards in the retainers.
2.
Troubleshooting
Malfunctions often have simple explanations. Refer to the table
before calling the after-sales service as you may be able to
remedy the fault yourself.
Malfunction table
If a dish doesn't turn out as well as you had hoped, refer to the
section Tested for you in our cooking studio, where you will
find plenty of cooking tips and tricks.
Problem
Possible cause Remedy/information
The oven does
The circuit
not work.
breaker is
defective.
Power cut
Power cut
and three
0
zeros light up in
the display.
The oven does
There is dust on
not heat up.
the contacts.
You wish to
The c04 basic
start the clean-
setting is set to
ing system, but
"no".
appears in
Ÿ©
the display.
The oven does
The oven is in
not heat up. A
demonstration
mode.
small square
Ü
lights up in the
display.
Automatic
appears in
"‰
switch-off has
the display.
been activated.
Error messages
If an error message with
"
message disappears. A time function that has been set is
cleared. If the error message does not disappear, please
contact the after-sales service.
You can take remedial action yourself if the following error
message is displayed.
16
Look in the fuse box and
check that the circuit
breaker is in working order.
Check whether the kitchen
light or other kitchen appli-
ances are working.
Reset the clock.
Turn the control knobs back
and forth several times.
Change the c04 basic set-
ting to selection 1 "yes".
Switch off the circuit
breaker in the fuse box and
switch it on again after
approximately 20 seconds.
Now, within approx.
2 minutes, press and hold
the
@
button for approx.
4 seconds until the square
Ü
goes out.
Turn the function selector to
the off position.
appears, press the
button. The
0
'
Refitting the door panel:
Slide in the door panel all the way.
1.
Put the cover back in place and screw it in.
2.
Refit the appliance door.
3.
Error message Possible cause Remedy/information
A button was
"‹‚‚
depressed for
too long or is
covered up.
ã=
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried
out by one of our trained after-sales engineers.
Replacing the oven light bulb
Replace faulty oven light bulbs.
Spare bulbs can be obtained from the after-sales service or
specialist retailers. Only use these oven light bulbs.
For the main oven: E14, 220 - 240 V, 40 W, heat-resistant to
■
300 °C.
For the top oven: E14, 220 - 240 V, 25 W, heat-resistant to
■
300 °C.
ã=
Risk of electric shock !
Disconnect the appliance from the power supply. Switch off the
circuit breaker or remove the fuse from the household fuse box.
Place a tea towel in the cold cooking compartment to prevent
1.
damage.
Turn the glass cover anticlockwise and remove it.
2.
Replace the oven light bulb with a bulb of the same type.
3.
Screw on the glass cover again.
4.
Remove the tea towel and switch on the circuit breaker.
5.
Note: Use rubber gloves if the glass cover cannot be
unscrewed: Or order a special removal tool from the after-sales
service:
For the main oven: Order no. 613634
■
For the top oven: Order no. 621743
■
Press all buttons individu-
ally. Check whether any but-
tons are jammed, covered
up or soiled.
Advertisement
Table of Contents
