Roger Technology B70/2ML Quick Start
  1. Manuals
  2. Brands
  3. Roger Technology Manuals
  4. Gate Opener
  5. B70/2ML
  6. Quick start
Roger Technology B70/2ML Quick Start

Roger Technology B70/2ML Quick Start

Hide thumbs Also See for B70/2ML:
1
2
3
4
5

Advertisement

Table of Contents

B70/2ML is the range of 24V DC digital controllers installed in the swing gates product.

1. Typical installation

3
3
A
Power supply B70/2ML - Motors 3x2,5 mm
1
Photocell - Receiver
2
Photocell - Transmitter
3
Flashing lamp unit
4
Antenna
5
Selector / Keypad
4
3
2
A
double insulated cable (max.10 m) - 3x4 mm
2
5x0,5 mm
double insulated cable (max.20 m)
2
3x0,5 mm
double insulated cable (max.20 m)
2
2x1 mm
double insulated cable (max.10 m)
2
RG58 50 Ohm cable for external use (max.10 m)
3x0,5 mm
cable (max.20 m)
2
Quick Start B70/2ML
2
Via S. Botticelli 8 • 31021 Bonisiolo di Mogliano Veneto (TV) • ITALIA
P.IVA 01612340263 • Tel. +39 041.5937023 • Fax. +39 041.5937024
info@rogertechnology.com • www.rogertechnology.com
EN
Rev00 11/11/2020
5
3
(max. 30 m)
2
ROGER TECHNOLOGY

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the B70/2ML and is the answer not in the manual?

Questions and answers

Related Manuals for Roger Technology B70/2ML

Summary of Contents for Roger Technology B70/2ML

  • Page 1 Quick Start B70/2ML Rev00 11/11/2020 B70/2ML is the range of 24V DC digital controllers installed in the swing gates product. 1. Typical installation Power supply B70/2ML - Motors 3x2,5 mm double insulated cable (max.10 m) - 3x4 mm (max. 30 m)
  • Page 2 2. Electrical connections MOTORE 2 MOTOR 2 TRANSFORMER PROG TEST F3.15mA WIFI FIFTHY/24 ISEL 1 2 3 1 2 3 4 5 COM PED AP COM MOTORE 1 Accessories illustrated are indicative only MOTOR 1 3. Display: functions and settings PARAMETER PARAMETER VALUE...
  • Page 3 4. Before starting ... a) Select the automation system model installed with the parameter A1. BE20 Series AYRON Series MONOS4 1 MOTOR 2 MOTORS b) Select the position of the motor relative to the gate with the parameter 70. This parameter is set for two motors by default. c) Position the mechanical stops in both the open and closed positions by tightening them very tightly.
  • Page 4 5. Acquisition procedure 1. Press and hold PROG for 4 seconds. 2. APP- appears on the display. 3. Press PROG. 4. AUTO appears on the display. 5. MOTOR 1 starts opening at low speed. 6. After the delay time set with parameter 25, MOTOR 2 starts an opening manoeuvre. 7.
  • Page 5 7. Programming a NEW transmitter L1 L2 L1 L2 L1 L2 1. Press channel P1 (P2) of the receiver. 2. When LED L1 (L2) flashes 3 times (or 4 times with rolling code function), press any button on the transmitter. 3.

Table of Contents