Related Manuals for SATO KEIRYOKI SK-1260
Summary of Contents for SATO KEIRYOKI SK-1260
- Page 1 INSTRUCTION MANUAL No. 8080-05 WATERPROOF DIGITAL THERMOMETER (With Print Output) MODEL SK-1260 3-4, Kanda Kajicho, Chiyodaku, Tokyo 101-0045 JAPAN TEL : + 81(0)3-3254-8117 FAX:(0)3-3254-8123 URL : http://www.sksato.co.jp/english/ Q.11...
- Page 2 Overview The SK-1260 is a waterproof digital thermometer to which dedicated thermistor sensor probe and dedicated thermocouple (K) sensor probe are connected. Measured data can be stored in the main unit and can...
-
Page 3: Table Of Contents
Warning II - 1. Setting Modes… ……………………………………………… 15 II - 2. Setting Time…………………………………………………… 15 The SK-1260 is not explosion-proof. Never use it in an atmosphere II - 3. Setting the Recording Interval………………………………… 16 containing flammable gases.… II - 4. Setting Management Numbers… …………………………… 17 II - 5. -
Page 4: Names And Functions Of Components
② HOLD / REL key 1. Names and Functions of Components ・ P ress the HOLD / REL key in normal measurement mode to hold (freeze) temperature readings. ・ P ress the HOLD / REL key in hold mode to enter REL (fluctuation) measurement mode. -
Page 5: Notes On Use
⑩ AC adapter jack ⓙ MAX : Lit while the maximum measured value is being ・Connect the dedicated AC adapter plug. displayed ⑪ Jack waterproof cover ⓚ MIN : Lit while the minimum measured value is being ・ W hen measuring temperature in the environment requiring displayed ⓛ... -
Page 6: Caution In Storage
・… T he sensors are specially designed for the SK-1260 Water free, then holding both sides of the lid, slide it out horizontally. -
Page 7: Connecting The Sensor Probe
⑸ Be sure to turn the power off before replacing the batteries. 7. Operating Procedure Otherwise, all data will be cleared. Please refer to flow of the operation that the usage on the SK-1260 5. Connecting the Sensor Probe digital thermometer. - Page 8 ⑵ Temperature measurement in manual or auto storage mode ⑶… Printing stored data ・Displaying stored data on the LCD panel. ・Printing stored data on a dedicated printer (option). Normal measurement mode Stored data exist Press the POWER and TIME Make sure that the main unit and Time setting mode keys simultaneously to enter Connect the printer...
-
Page 9: I General Temperature Measurement Methods
Ⅰ General Temperature Measurement Methods measured temperature is continuously displayed on the sub 7-segment display so that you can check the current temperature Ⅰ-1. Temperature Measurement Method while holding the necessary temperature reading. ⑴ Connect the sensor probe to the main unit. ⑵... -
Page 10: I - 4. Alarm Setting Of Upper And Lower Limits
⑷ The operation mode can be switched in the cycle shown below. Ⅰ - 6. Auto Power-off Function ・The power will be turned off automatically if the unit is not operated Normal measurement mode for approximately 30 minutes. This function conserves battery power if you forget to turn the power off. -
Page 11: Methods For Measuring Temperature In Storage Mode
Ⅱ Methods for Measuring Temperature in Storage Mode Ⅱ- 3. Setting the Recording Interval Press the POWER and HOLD / REL keys simultaneously while Ⅱ- 1. On Setting Modes the main unit is on. Set the recording interval with the following When you enter a setting mode, the numerical values that can be set procedure. -
Page 12: 4. Setting Management Numbers
Ⅱ- 4. Setting Management Numbers • Calling Stored Data In case the stored data is present in the unit, press the TIME key Press the POWER and MAX / MIN keys simultaneously while the for at least one second to display the stored temperature values main unit is on to set the management number. -
Page 13: Printing Stored Data
2. If the auto storage ends while power is ON and AC adapter is ⑶ This is a dedicated printer (option) for the SK-1260. To purchase connected with unit, be sure to firstly pull out the jack of AC adapter this printer, contact the dealer from which the SK-1260 was from the unit. -
Page 14: 3. Examples Of The Printed Data
Ⅳ Error Message Ⅲ-3. Examples of the Printed Data Manual storage mode • Error massage is displayed on the main 7-segment LCD Display Causes Remedy Measuring Data Print-Date : 2016 / 9 / 23 Mes-Code : No. 00-00 (°C) Measured value is higher Er : Hi than measuring range. -
Page 15: Specifications
Ⅴ Specifications Ⅵ Optional Accessories No. 8009-50 Dedicated printer Model DPU-414 Product No. 8080-05 Waterproof Digital Thermometer Power requirements: AC adapter or built-in battery SK - 1260 Model Accessories: 1 ea. of roll paper, cable, AC adapter in 100 Thermistor : - 30.0 to 199.9°C Measuring range to 240VAC use K Thermocouple : - 99.9 to 1250°C...
Need help?
Do you have a question about the SK-1260 and is the answer not in the manual?
Questions and answers