Table of Contents
Advertisement
2.
Insert the proper accessory for the item to be
3.
•
• No accessory is needed for common car/truck
tyre schrader valves.
• For car/truck tyres, screw schrader chuck onto
tyre valve and ensure it is tight.
4. Insert the battery pack.
5.
To turn on, press the Power
will detect the current air pressure of the item.
6.
Use the
and
sure, if desired. Press and hold
to jump down or up faster.
NOTE: Setting target pressure is not recom-
mended when using the accessory nozzles.
NOTE:
is greater than the target pressure, the tool will not
7.
NOTE:
necting indicate the tool is recalibrating pressure.
The tool will shut off automatically once the target
pressure has been reached. Target mode shows
0 PSI if no target pressure is set. Inflator will run
until 150 PSI max pressure.
CAUTION: Allow tool to cool for 10 minutes after
each 10 minutes of continuous use.
button.
NOTE: The tool will shut down after 5 minutes of
inactivity.
Memory Settings
To view memory settings, press the memory button
to navigate through memory slots M1 - M4. After
reaching memory slot M4, pressing the memory
button again will save any new settings and return
to the home screen.
To adjust memory settings:
Press the memory button to navigate M1 – M4.
1.
Press the
or
2.
memory setting.
1.
Press and hold Memory button for 2 seconds to
save memory setting.
2.
Target inflation numbers will flash twice to
confirm the save.
Troubleshooting
actual value reads greater than zero when not con-
nected to any object, the pressure sensor may have
drifted due to altitude or other factors.
To reset:
Press and hold the
together for 3 seconds to set pressure gauge to
zero.
button. The tool
buttons to set the target pres-
or
button or power
button to increase/decrease
Button and Inflation Button
Sports Needle/Raft Nozzle
Be careful not to bend the accessory. Remove after
Use the Presta valve with Presta valve stems. Before
seal the valve.
WARNING
buttons
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
-
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage
of parts, or any other condition that may affect the
tool operation. Return the tool, battery pack, and
charger to a MILWAUKEE
repair. After six months to one year, depending on
use, return the tool, battery pack and charger to a
MILWAUKEE
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a MILWAUKEE
WARNING
your tool, battery pack or charger in liquid or
Clean dust and debris from any vents. Keep tool
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain
cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include
petrol, turpentine, lacquer thinner, paint thinner,
chlorinated
household detergents containing ammonia. Never
use flammable or combustible solvents around
tools.
For repairs, return the tool, battery pack and charger
to the nearest authorised service centre.
WARNING
For a complete listing of accessories, go online to
milwaukeetool.com.au/
contact a distributor.
5
Presta Valve
MAINTENANCE
To reduce the risk of injury, always
unplug the charger and remove the
®
service facility for ALL repairs.
Maintaining Tool
service facility for
®
service facility for inspection.
®
service facility for repairs.
®
To reduce the risk of personal in-
jury and damage, never immerse
Cleaning
cleaning
solvents,
Repairs
ACCESSORIES
Use only recommended accesso-
ries. Others may be hazardous.
milwaukeetool.co.nz
ammonia
and
or
Advertisement
Table of Contents
